Husqvarna PZ5426FX Owners Manual - Page 23

Tracking Knob, Cutting Height Pedals, Loosen tracking knob out until flush with nut.

Get Husqvarna PZ5426FX PDF manuals and user guides View all Husqvarna PZ5426FX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

CONTROLS Tracking Knob If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure for the rear tires is 15 psi (1 bar). 1. Tracking adjustments are made using the tracking bolt and tracking knob. The tracking bolt and tracking knob act as limiting devices for the motion control levers when in the full-forward position. 2. For preliminary tracking adjustment, move unit to an open, unobstructed area such as an empty parking lot or open field. 3. Back the tracking bolt out until flush with nut. 4. Loosen tracking knob out until flush with nut. 5. Test operate unit by driving it at full throttle and the full forward position on both motion control levers. Gradually turn in the tracking bolt on the right hand side until the unit noticeably starts drifting right. 6. Drive forward at full throttle with both motion control levers in the full forward position. Gradually turn in the tracking knob (left side) until unit tracks straight. Tracking adjustment 8065-060 Cutting Height Pedals The cutting height pedals release the deck lift to allow setting the desired deck height. Apply pressure to the lift pedal and rotate foot to also apply pressure to the release pedal, unlocking the deck lift. For transport, push the lift pedal fully forward until the deck lift latches in the transport (highest) position. 2 1 1. Lift pedal 2. Release pedal Cut height selection pedals 8065-017 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
CONTROLS
23
1
2
Cutting Height Pedals
The cutting height pedals release the deck lift to allow
setting the desired deck height. Apply pressure to the
lift pedal and rotate foot to also apply pressure to the
release pedal, unlocking the deck lift.
For transport, push the lift pedal fully forward until the
deck lift latches in the transport (highest) position.
8065-017
1. Lift pedal
2. Release pedal
Cut height selection pedals
Tracking Knob
If the mower is not tracking straight, check the
air pressure in both rear tires. Recommended air
pressure for the rear tires is 15 psi (1 bar).
1.
Tracking adjustments are made using the tracking
bolt and tracking knob. The tracking bolt and
tracking knob act as limiting devices for the
motion control levers when in the full-forward
position.
2.
For preliminary tracking adjustment, move unit
to an open, unobstructed area such as an empty
parking lot or open field.
3.
Back the tracking bolt out until flush with nut.
4.
Loosen tracking knob out until flush with nut.
5.
Test operate unit by driving it at full throttle and
the full forward position on both motion control
levers. Gradually turn in the tracking bolt on the
right hand side until the unit noticeably starts
drifting right.
6.
Drive forward at full throttle with both motion
control levers in the full forward position.
Gradually turn in the tracking knob (left side) until
unit tracks straight.
8065-060
Tracking adjustment