Husqvarna PZ5430 Owners Manual - Page 44

Deck Belt, Deck Belt Removal, Deck Belt Installation

Get Husqvarna PZ5430 PDF manuals and user guides View all Husqvarna PZ5430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

MAINTENANCE Deck Belt Deck Belt Removal Park on a level surface. Apply park brake. Lower the deck into the lowest cutting position. 1. Remove foot plate and belt shields. 2. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface. 3. With a ½" breaker bar and using the square opening in the idler arm, shift the arm counter clockwise to relieve the tension on the belt. 4. Carefully roll the belt over the top of the cutter housing pulleys. 5. Remove the belt guide hardware with a ½" wrench and set belt guide aside. 6. Remove the belt from around the electric clutch on the engine shaft. Release the belt tension 8065-040 Deck Belt Installation NOTE: For ease in installing the deck belt, refer to the routing decal on the cutting deck. 1. Place the belt around all the pulleys except the center spindle pulley. 2. With a ½" breaker bar, shift the idler arm counter clockwise. When there is enough slack, slip the belt onto the center spindle pulley. 3. Reinstall the belt guide removed in Step 5 above. 4. Double check belt routing to make sure it matches the routing decal, and that the belt does not have any twist. Correct if needed. Remove belt guide 8065-046 Refer to belt routing decal 8065-047 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
MAINTENANCE
44
8065-040
Release the belt tension
Deck Belt
Deck Belt Removal
Park on a level surface. Apply park brake. Lower the
deck into the lowest cutting position.
1.
Remove foot plate and belt shields.
2.
Remove any dirt or grass that may have
accumulated around the cutter housings and
entire deck surface.
3.
With a ½" breaker bar and using the square
opening in the idler arm, shift the arm counter
clockwise to relieve the tension on the belt.
4.
Carefully roll the belt over the top of the cutter
housing pulleys.
5.
Remove the belt guide hardware with a ½" wrench
and set belt guide aside.
6.
Remove the belt from around the electric clutch
on the engine shaft.
8065-046
Remove belt guide
Deck Belt Installation
NOTE: For ease in installing the deck belt, refer to the
routing decal on the cutting deck.
1.
Place the belt around all the pulleys except the
center spindle pulley.
2.
With a ½" breaker bar, shift the idler arm counter
clockwise. When there is enough slack, slip the
belt onto the center spindle pulley.
3.
Reinstall the belt guide removed in Step 5 above.
4.
Double check belt routing to make sure it matches
the routing decal, and that the belt does not have
any twist. Correct if needed.
8065-047
Refer to belt routing decal