Husqvarna R 220T Operation Manual
Husqvarna R 220T Manual
 |
View all Husqvarna R 220T manuals
Add to My Manuals
Save this manual to your list of manuals |
Husqvarna R 220T manual content summary:
- Husqvarna R 220T | Operation Manual - Page 1
Operator′s manual Rider 220T Rider 322T AWD Please read the operator's manual carefully and make sure you understand the instructions before using the machine. English - Husqvarna R 220T | Operation Manual - Page 2
Use 4 Good service 4 KEY TO SYMBOLS Symbols 8 WHAT IS WHAT? What is what on the ride-on mower 10 SAFETY INSTRUCTIONS Safety instructions 11 Driving on slopes 12 Children 13 Maintenance 19 Driving the Rider 19 Cutting tips 20 Stop the engine 20 Maintenance Maintenance schedule 21 Cleaning - Husqvarna R 220T | Operation Manual - Page 3
second-hand value of the machine. Range of applications for BioClip. Complete proof of sale etc. Pre-delivery service carried out. No outstanding problems. Certified: Date, mileage, stamp, signature After the first 8 hours and rear wheels. (Only AWD-machines) See the workshop manual. English - 3 - Husqvarna R 220T | Operation Manual - Page 4
a valuable document. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value. When you sell your Rider, make sure you pass on the operator's manual to the new owner. The last chapter in the operator - Husqvarna R 220T | Operation Manual - Page 5
ride-on mowers These instructions are for your safety. Read them carefully. IMPORTANT! This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions near or crossing roadways. 15.Use extra care when loading or unloading - Husqvarna R 220T | Operation Manual - Page 6
check components and replace with manufacturer's recommended parts, when necessary. 9. Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them. 10. Check brake operation frequently. Adjust and service as required. Safe handling of gasoline To - Husqvarna R 220T | Operation Manual - Page 7
instructions are delivered with the accessory. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service or injury. Safe operation practices for Ride-On Mowers Before starting cutting operations, train different - Husqvarna R 220T | Operation Manual - Page 8
or fatal injury to the operator or others. Clutch out Warning: rotating parts. Keep hands and feet clear. Please read the operator's manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved hearing protection Rotary blades Keep hands and - Husqvarna R 220T | Operation Manual - Page 9
Switch off the engine and take off the ignition cable before repairs or maintenance Check the engine's oil level Check transmission oil level Lift up the cutting unit Apply the parking brake. If the engine is cold, use the choke Release the parking brake before driving The following labels are on - Husqvarna R 220T | Operation Manual - Page 10
12 34 5 67 8 9 10 11 12 13 14 15 16 What is what on the ride-on mower 1 Speed limiter for driving forward 2 Speed limiter for reversing 3 Lifting lever for the cutting unit 15 Battery 16 Lever to disengage the drive Rider 220T Lever to disengage the driving rear axle, 322T AWD English - 10 - Husqvarna R 220T | Operation Manual - Page 11
Check the insurance coverage for your new Rider. • Contact your insurance company. • You should have fully comprehensive insurance including: third party, fire, damage, theft and liability General use • Read all the instructions in this operator's manual and on the machine before you start it. Ensure - Husqvarna R 220T | Operation Manual - Page 12
INSTRUCTIONS • Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may regulate the age of the user. This is what you do • Remove obstacles such as stones, branches, etc. • Mow upwards and downwards, not sideways. WARNING! You must use - Husqvarna R 220T | Operation Manual - Page 13
INSTRUCTIONS dealer concerning the use of wheel weights if you are unsure. Wheel weights can not be used on AWD-machines. Use Never allow children to ride along. They can your view. Maintenance • Stop the be started until the problem has been resolved. • parts if the engine is started with - Husqvarna R 220T | Operation Manual - Page 14
SAFETY INSTRUCTIONS • Do not change the setting of governors. If you run too fast, you risk damaging the machine components. See chapter on Technical data for highest permitted engine speed. • Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon - Husqvarna R 220T | Operation Manual - Page 15
product that will give you great pleasure for many years. This operator's manual describes Rider 220T and Rider 322T AWD. Speed limiter The speed of the machine is steplessly regulated with two pedals. Pedal (1) is used to drive forwards, and pedal (2) to drive backwards. 1 2 The machine 322T AWD - Husqvarna R 220T | Operation Manual - Page 16
tipped forward. The lever can also be used to temporarily regulate the cutting height, e.g. for a small mound in the lawn. Cutting height adjustment lever The cutting height . ! Exercise care and refuel outdoors (see safety instructions). IMPORTANT! Do not use the fuel tank as a support area. - Husqvarna R 220T | Operation Manual - Page 17
to the end positions, do not use an intermediate position. Clutch control Rider 322T AWD Rider 316T AWD and Rider 316Ts AWD have one control for the both clutch controls pressed in. • Clutch control, rear axle Release lever Rider 220T • Pull out the control to disengage the drive system. Push in - Husqvarna R 220T | Operation Manual - Page 18
instructions and information concerning the placement of controls and functions before starting. • Perform daily maintenance before starting as set out in the Maintenance 1 Make sure that the clutch control is depressed. Rider 316T AWD and Rider 316Ts AWD have one control for the front axle and - Husqvarna R 220T | Operation Manual - Page 19
batteries. If the battery is too weak to start the engine, it should be recharged. When jump leads are used for emergency starting, follow the procedure below: IMPORTANT INFORMATION Your Rider is equipped with a 12-volt system with negative earth. The other vehicle must also have a 12-volt system - Husqvarna R 220T | Operation Manual - Page 20
blades rotate rapidly) and low speed (the Rider moves slowly). If the grass is not lawn. The mowing results will then be poorer. • Hose down the cutting unit with water underneath each time it is used. The cutting unit should then be put in the service position. • When the BioClip function is used - Husqvarna R 220T | Operation Manual - Page 21
points not described in this manual, visit an authorised service workshop. Maintenance Cleaning Check the engine's oil O X O XX X X O X 1)If the machine is used daily it should be lubricated twice a week. 2) Maintenance and replacement are required more often in dusty conditions. 3)First change - Husqvarna R 220T | Operation Manual - Page 22
and electrical connections. Corrosion attack can result, which will lead to running problems. Cleaning additives generally aggravate the damage. Removing of the machine hoods Engine cover The engine becomes accessible for service when the engine cover is opened. Fold the seat forward, loosen the - Husqvarna R 220T | Operation Manual - Page 23
Adjusting the parking brake Rider 220T The parking brake is adjusted as follows: 1 Loosen the locking nuts (1). 2 Tension the cable using the adjuster screw (2) is achieved at full throttle. If doubts arise, contact your service representative. If adjustment is necessary, adjust the lower wire as - Husqvarna R 220T | Operation Manual - Page 24
replace the air filter at regular intervals (see Maintenance/Maintenance Schedule for the correct service interval). Replace the air filter as follows: 1 follows: 1 Open the engine cover. 2 Move the hose clips away from the filter. Use a pair of flat pliers. 3 Pull off the filter from the hose ends. 4 - Husqvarna R 220T | Operation Manual - Page 25
with an electronic ignition system. Only the spark plug requires maintenance. For recommended spark plug, see Technical data. IMPORTANT INFORMATION spark plug spanner. Tighten the spark plug so that the washer is compressed. A used spark plug should be turned 1/8 of a turn from the seated position. A - Husqvarna R 220T | Operation Manual - Page 26
Maintenance Replacing the light bulbs: 322T AWD For information about the bulb type, lamps in the lower slot on the lamp housing. 5 Press the lamp in place in the locking bracket Do not use any other type of fuse when replacing. A blown fuse is indicated by a burnt connector. Pull the fuse from - Husqvarna R 220T | Operation Manual - Page 27
Maintenance which can damage the engine. 5 Push the deck in and put the front guide plugs in the grooves on the equipment frame, one on each side. WARNING! tensions up the belt may break and cause personal injury. 1 Place the Rider on a flat surface and apply the parking brake. 2 Check that the - Husqvarna R 220T | Operation Manual - Page 28
Maintenance put the cutting unit in the service position, see Service position for the cutting unit. it. Pressure is adjusted using a screw and spring on each side of the Rider. 1 Check the air pressure placed between the frame and scales so that the support wheels do not bear any weight. 5 Adjust - Husqvarna R 220T | Operation Manual - Page 29
Maintenance Checking the cutting unit's parallelism Check the cutting unit's parallelism as follows: 1 Check the air pressure in the tyres 60 kPa/0.6 kp/cm2/8.5 PSI. 2 Place - Husqvarna R 220T | Operation Manual - Page 30
Maintenance 7 Remove the screws on the cutting cover. Lift the unit frame and Assemble the parts in the reverse order. Service position for the cutting unit The cutting head can be placed in the service position to provide easy access for cleaning, repairs and servicing. In the service position the - Husqvarna R 220T | Operation Manual - Page 31
Maintenance 2 Replace the cutting height stay and the belt. 3 Tension the belt remove the BioClip plug located under the unit with three screws. 1 Put the unit in the service position, see Placing in the service position. 2 Remove the three screws holding the BioClip plug, and remove the plug. 4 - Husqvarna R 220T | Operation Manual - Page 32
when the Rider stands horizontal The following oil classes are recommended: • API Service Class: SF, SG, SH and SJ Choose . See Checking the engine's oil level for filling instructions. The engine holds 1.5 litres (1.6 USqt) when the rubber seal on the new oil filter using new oil. Fit the oil filter by - Husqvarna R 220T | Operation Manual - Page 33
the transmission's oil tank. Rider 220T Fill if necessary with engine oil SAE 10W/40 (class SF-CC). Rider 322T AWD Fill if necessary with oil Synthetic 10W/50 The oil and filter should be changed by an authorised service representative, as described in the Workshop Manual. Work on the system entails - Husqvarna R 220T | Operation Manual - Page 34
Troubleshooting schedule Problem Procedure Engine does not start There is no fuel in the fuel tank Spark plug defective Faulty spark plug connections or interchanged cables Dirt in - Husqvarna R 220T | Operation Manual - Page 35
use petrol for cleaning purposes. Use degreasing agents and hot water instead. To prepare the machine for storage follow these instructions: parts state your machine's purchase year, model, type, and serial number. Always use genuine parts. Annual inspection or tuning by an authorised service - Husqvarna R 220T | Operation Manual - Page 36
Technical data Dimensions Rider 220T Rider 322T AWD Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 890/2,92 890/2,92 Height, mm/ft - Husqvarna R 220T | Operation Manual - Page 37
to the dealer or to an applicable station for recycling. IMPORTANT INFORMATION We reserve the right to change specifications and designs without prior notice so as to implement improvements. Note that no legal claims are valid on the basis of information in this manual. Use only genuine parts for - Husqvarna R 220T | Operation Manual - Page 38
- Husqvarna R 220T | Operation Manual - Page 39
- Husqvarna R 220T | Operation Manual - Page 40
Original instructions 1154551-95 ´´®®zz++VVWW,,¶¶66%%¨¨ 2012-02-03
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
 |
 |
English
Rider 220T
Rider 322T AWD
Oper
ator
′
s manual
Please r
ead the operator’s manual carefully and make sure you
understand the instructions before using the machine.