IBM 84802AX User Guide - Page 29

This field controls what IRQ the Advanced Configuration and Power Interface

Get IBM 84802AX PDF manuals and user guides View all IBM 84802AX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

- IDE Hard Disk Standby Timer This field controls what IRQ the Advanced Configuration and Power Interface (ACPI) uses. - Time to Low Power Select this choice to set the time that will elapse from the last keyboard or mouse activity until the server assumes a low power sleep state. - Sleep Mode You can set this menu choice only if Time to Low Power is set. - Power Switch < 4 sec. You can set this to Power Off or Suspend. - System wake-up event Select this choice to control the event that occurs when the server wakes up. - Serial Port Ring Detect Set this menu choice to Enabled to set the server to wake up when activity is detected on the serial port modem. - Wake Up on Alarm Select this choice to set the server to wake up at a certain day or time. You can set this to Disabled, Time, and Date/Time. - Alarm Day of Month You can set this menu item only if you have set Wake Up on Alarm to Time or Date/Time. Set the day of the month for the server to wake up. - Alarm Time You can set this menu item only if you have set Wake Up on Alarm to Time or Date/Time. Set the time of the day for the server to wake up. - ACPI Sleep State Select which power level your server uses in Standby mode. If S1 is selected, power is maintained to all devices, but all processor activity is halted. If S3 is selected, power is maintained only for the main memory. Exit from the S3 state might not be supported by all installed adapters. - Restart on AC/Power Failure This field controls whether the system will stay on after ac power is removed and then restored. Select Power On if you use a power strip to turn on the server. Select Stay Off if you want the server to remain off after power is restored. Select Last State to have the server return to its previous state. • Error Logs Select this menu choice to view any errors that occur during POST. • Save Settings Select this choice to save your customized settings. • Restore Settings Select this choice to restore the previous settings. • Load Default Settings Select this choice to restore the factory settings. • Exit Setup Select this choice to exit from the Configuration/Setup Utility program. If you have made any changes, the program will prompt you to save the changes or exit without saving the changes. Chapter 2. Configuring your server 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Chapter 2.
Configuring your server
17
—
IDE Hard Disk Standby Timer
This field controls what IRQ the Advanced Configuration and Power Interface
(ACPI) uses.
—
Time to Low Power
Select this choice to set the time that will elapse from the last keyboard or
mouse activity until the server assumes a low power sleep state.
—
Sleep Mode
You can set this menu choice only if Time to Low Power is set.
—
Power Switch < 4 sec.
You can set this to
Power Off
or
Suspend
.
—
System wake-up event
Select this choice to control the event that occurs when the server wakes up.
—
Serial Port Ring Detect
Set this menu choice to
Enabled
to set the server to wake up when activity is
detected on the serial port modem.
—
Wake Up on Alarm
Select this choice to set the server to wake up at a certain day or time.
You
can set this to
Disabled
,
Time
, and
Date/Time
.
—
Alarm Day of Month
You can set this menu item only if you have set
Wake Up on Alarm
to
Time
or
Date/Time
.
Set the day of the month for the server to wake up.
—
Alarm Time
You can set this menu item only if you have set
Wake Up on Alarm
to
Time
or
Date/Time
.
Set the time of the day for the server to wake up.
—
ACPI Sleep State
Select which power level your server uses in Standby mode.
If S1 is selected,
power is maintained to all devices, but all processor activity is halted.
If S3 is
selected, power is maintained only for the main memory.
Exit from the S3
state might not be supported by all installed adapters.
—
Restart on AC/Power Failure
This field controls whether the system will stay on after ac power is removed
and then restored.
Select
Power On
if you use a power strip to turn on the
server.
Select
Stay Off
if you want the server to remain off after power is
restored.
Select
Last State
to have the server return to its previous state.
•
Error Logs
Select this menu choice to view any errors that occur during POST.
•
Save Settings
Select this choice to save your customized settings.
•
Restore Settings
Select this choice to restore the previous settings.
•
Load Default Settings
Select this choice to restore the factory settings.
•
Exit Setup
Select this choice to exit from the Configuration/Setup Utility program.
If you have made any changes, the program will prompt you to save the changes
or exit without saving the changes.