IBM 8835 Installation Guide - Page 34

Installing a non-hot-swap hard disk drive, Notes

Get IBM 8835 - Eserver 325 - 1 GB RAM PDF manuals and user guides
UPC - 000435158314
View all IBM 8835 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Installing a non-hot-swap hard disk drive Before you install a non-hot-swap hard disk drive, read the following information: v See the documentation that comes with the drive for any cabling instructions. v Route the cable before you install the drive. Do not block the airflow from the fans. Complete the following steps to install a non-hot-swap hard disk drive: Drive bay 2 Drive bay 1 1. Read the safety information beginning on page v, and "Installation guidelines" on page 9. 2. Turn off the server and all attached peripheral devices. Disconnect all power cords; then, disconnect all external signal cables from the server. 3. Remove the server from the rack; then, remove the server cover (see "Removing the cover and bezel" on page 11). 4. Press in on the USB option tray to release it and slide the tray out until it stops; then, press the retention clip at the bottom rear of the tray and remove the tray from the server. Press on the bezel retention tabs and pull the bezel directly away from the server. Notes: a. If you have only one non-hot-swap hard disk drive, install it in the right-hand bay (bay 2) with a jumper installed in the cable-selection-enabled position of the jumper block on the rear of the drive. b. If you have two drives and you want the server to determine the master drive and subordinate drive automatically, install jumpers in the cable-selection-enabled position of the jumper block on both drives. c. If you want to assign master and subordinate drives manually, install a jumper in the master position for the drive in bay 2 and install a jumper in the subordinate position for the drive in bay 1. 5. Install the hard disk drive in the drive bay: a. Attach the rails to the sides of the drive using 2 screws for each rail. b. Slide the drive into the bay until the rail latches snap into place. c. Connect the signal and power cables to the rear of the drive. Keep the cables clear of the airflow path of the fan behind the drive bays. 6. If you have other options to install, install them now. Otherwise, go to "Completing the installation" on page 31. 20 IBM 325 Type 8835: Option Installation Guide Eserver

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Installing a non-hot-swap hard disk drive
Before you install a non-hot-swap hard disk drive, read the following information:
v
See the documentation that comes with the drive for any cabling instructions.
v
Route the cable
before
you install the drive. Do not block the airflow from the
fans.
Complete the following steps to install a non-hot-swap hard disk drive:
Drive bay 1
Drive bay 2
1.
Read the safety information beginning on page v, and “Installation guidelines” on
page 9.
2.
Turn off the server and all attached peripheral devices. Disconnect all power
cords; then, disconnect all external signal cables from the server.
3.
Remove the server from the rack; then, remove the server cover (see
“Removing the cover and bezel” on page 11).
4.
Press in on the USB option tray to release it and slide the tray out until it stops;
then, press the retention clip at the bottom rear of the tray and remove the tray
from the server. Press on the bezel retention tabs and pull the bezel directly
away from the server.
Notes:
a.
If you have only one non-hot-swap hard disk drive, install it in the right-hand
bay (bay 2) with a jumper installed in the cable-selection-enabled position of
the jumper block on the rear of the drive.
b.
If you have two drives and you want the server to determine the master
drive and subordinate drive automatically, install jumpers in the
cable-selection-enabled position of the jumper block on both drives.
c.
If you want to assign master and subordinate drives manually, install a
jumper in the master position for the drive in bay 2 and install a jumper in
the subordinate position for the drive in bay 1.
5.
Install the hard disk drive in the drive bay:
a.
Attach the rails to the sides of the drive using 2 screws for each rail.
b.
Slide the drive into the bay until the rail latches snap into place.
c.
Connect the signal and power cables to the rear of the drive. Keep the
cables clear of the airflow path of the fan behind the drive bays.
6.
If you have other options to install, install them now. Otherwise, go to
“Completing the installation” on page 31.
20
IBM
Eserver
325 Type 8835: Option Installation Guide