Icom IC-M802 Instruction Manual

Icom IC-M802 Manual

Get Icom IC-M802 PDF manuals and user guides View all Icom IC-M802 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-M802 manual content summary:

  • Icom IC-M802 | Instruction Manual - Page 1
    INSTRUCTION MANUAL MF/HF MARINE TRANSCEIVER iM802
  • Icom IC-M802 | Instruction Manual - Page 2
    went into the design of your IC-M802. D FEATURES ❍ Standard 4×8″ remote controller ❍ Built-in DSC meets ITU Class E requirement ❍ E-mail function available ❍ PC connection capability for remote control IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver
  • Icom IC-M802 | Instruction Manual - Page 3
    on the microphone and send CHANNEL NAME PROGRAMMING 14 6 DSC PREPARATION 15-16 I MMSI code programming 15 I Position and time programming INSTALLATION 53-62 I Supplied accessories 53 I Front panel connections 53 I Rear panel connections 54 I Ground connection 55 I Power source 55 I Antenna
  • Icom IC-M802 | Instruction Manual - Page 4
    to set a Channel/Group The IC-M802 has up to 160 user-programmable, 242 ITU SSB duplex, 72 ITU SSB simplex and 662 ITU FSK duplex channels. D Using the group and channel selectors [GRP] [CH] q Rotate [GRP] to select the desired group. • Available groups are shown in the list below. •During user
  • Icom IC-M802 | Instruction Manual - Page 5
    [2 SQL] [F] [VOL] J3E SIMP [F] [2 SQL] • Squelch level adjustment q Push [F] then [2 SQL] to turn the squelch function ON. • Select the desired frequency/channel in advance, if desired. w Push [F] then [MODE SET] to enter quick set mode. [F] [MODE SET] [2 SQL] [GRP] [CH] SQL L CH ---GPS--- Lat
  • Icom IC-M802 | Instruction Manual - Page 6
    The transmit frequency is displayed and "TX" blinks. • When the channel is busy, wait until it becomes clear, or change the channel. r When the optional AT-140 is connected, push [TUNE THRU] to start manual tuning. • "TUNE" appears when the antenna is tuned. • "TUNE" blinks when a tuning error has
  • Icom IC-M802 | Instruction Manual - Page 7
    , such as an individual, group or all ships call on the desired frequencies, push [DSC] to enter DSC watching mode. • Monitoring the frequencies, 2187.5, 4207.5, 6312.0, 8414.5, 12577.0 and 16084.5 kHz, for distress, urgency, etc., no operation is necessary with the transceiver. These
  • Icom IC-M802 | Instruction Manual - Page 8
    Latitude 34 34'N Longitude 135 34'E UTC 12:34 Null OK y Rotate [CH] to select the DSC calling frequencies, then push [ENT]. • After pushing [ENT], return to DSC menu as shown in step e. ******* Distress ******* -------- Attempt ------- ÇSingle;six frequency Single; 2187.5kHz Single; 4207
  • Icom IC-M802 | Instruction Manual - Page 9
    Time Coordinated (UTC) is frequently used. w Adjustments, repairs, channel frequency changes and authorized modifications affecting electrical op- 1 eration of be posted or kept with the operator. Only a licensed radio operator may operate the transceiver. However, non-licensed individuals may
  • Icom IC-M802 | Instruction Manual - Page 10
    microphone. • See p. 66 for appropriate microphones. • See p. 61 for microphone connector information. y GROUP SELECTOR [GRP] ➥ Selects groups in 20 channel steps and ITU marine channel the transmit frequency while holding. (p. 10) ➥ During DSC watch mode, enters TX memory select screen. (p. 43)
  • Icom IC-M802 | Instruction Manual - Page 11
    channel name programming mode, when channel comment indication is ON. (p. 14) !3 KEYPAD ➥Inputs numeral "1" for channel number input, etc. ➥ Inputs "1," "Q," "Z," "q," "z" or space for channel optional antenna tuner is connected. • "TUNE" appears when tuned. • When the tuner cannot tune the antenna,
  • Icom IC-M802 | Instruction Manual - Page 12
    manual input for DSC operation . w REMOTE CONNECTOR [REMOTE] (pgs. 53, 62) Connects to a PC via an RS-232C cable (D-sub 9pin) for remote control in the NMEA or RS-232C format. e MODEM CONNECTOR [AF/MOD] (pgs. 53, 62) Connects to an e-mail modem, NBDP (Narrow Band Direct Printing) or FAX
  • Icom IC-M802 | Instruction Manual - Page 13
    Ω matched coaxial cable with a PL-259 plug for DSC receiver. t DC POWER SOCKET (p. 54, 61) Accepts 13.6 V DC through the supplied DC power cable. ✔ For detailed "ANTENNA AND GROUNDING CONSIDERATIONS," see pages 63 to 65. I Microphone (HM-135) q Microphone w e q PTT SWITCH [PTT] Push and hold to
  • Icom IC-M802 | Instruction Manual - Page 14
    M802 has 2 indication types, one is channel name indication and the other is frequency indication. These indication types can be switched with a push of a button, depending on set mode's setting. See pages 8 and 50 for display type settings. • Channel 23 !0 !1 !7 • DSC watch mode indication t
  • Icom IC-M802 | Instruction Manual - Page 15
    " blinks while tuning, if an optional external antenna tuner is connected. (p. 10) • "TUNE channel name is programmed, or during frequency indication. ➥ During DSC watch mode, displays "DSC WATCH." !7 TRANSMIT FREQUENCY READOUT Shows transmit frequency. !8 OPERATING GUIDE INDICATION During DSC
  • Icom IC-M802 | Instruction Manual - Page 16
    optionally restricted. D Display selection FREQUENCY indication RX J3E SIMP CH 16:23 CHANNEL indication RX J3E SIMP CH ---GPS--- Lat 45 59'N Lon134 44'E L H 16:23 ITU SSB channels NOTE: Channel name (alphanumeric) may not appear during frequency indication depending on initial set
  • Icom IC-M802 | Instruction Manual - Page 17
    channel. •A user channel is selected when channel 1-160 is input (max. number may be optionally restricted). • An ITU SSB channel is selected when channel user channels; or all channels in the group of ITU channels. Programmed scan scans frequencies within the frequency range between user channels
  • Icom IC-M802 | Instruction Manual - Page 18
    the desired operating mode. t Push [TUNE THRU] to tune the antenna tuner, if connected. • Skip this operation when the "AUTO TUNE" is set to ON in initial set mode (p. 50). y To transmit on the channel, push and hold the PTT switch on the microphone. • "TUNE" blinks for 1 to 2 sec. for the first
  • Icom IC-M802 | Instruction Manual - Page 19
    4 RECEIVE AND TRANSMIT I Functions for receive D Squelch function The squelch function detects signals with voice components and squelches (mutes) unwanted signals such as unmodulated beat signals. This provides quiet stand-by. When you need to receive weak signals, the squelch should be turned OFF
  • Icom IC-M802 | Instruction Manual - Page 20
    -M802 your antenna manual transmission with microphone channel to operate CW mode. e If the selected channel is not in A1A mode, push [MODE SET] several times to select "A1A." r Operate the CW keyer to transmit a CW signal. CW key connection PTT* To pin 3 76 381 54 2 To pin 1 To pin 2 *manual
  • Icom IC-M802 | Instruction Manual - Page 21
    ACC] socket as shown at right. w Select the desired channel to operate FSK mode. • FSK ITU channel group, Ch 4001 to Ch 25040, are only available mode (p. 51) ➥ Some transceivers may operate 1.7 kHz higher than the IC-M802's J2B mode even when the same displayed frequencies are in use. FSK terminal
  • Icom IC-M802 | Instruction Manual - Page 22
    that character. RX J3E DUP CH ---GPS--- Lat 45 59'N Lon134 44'E L H 16:23 y Repeat steps r and t to enter the channel name. u Push [ENT] to program the channel name. RX J3E DUP CH ---GPS--- Lat 45 59'N Lon134 44'E L H 16:23 • Available characters KEY CHARACTERS (space) KEY
  • Icom IC-M802 | Instruction Manual - Page 23
    9-digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be programmed. D Programming [DSC] [MODE SET] [ENT] [CH] [F] [POWER] q While pushing [F] and [DSC], push [POWER] to turn the power ON. w Push [DSC] to select DSC watch mode. e Push [MODE SET]. • DSC menu is selected as follows
  • Icom IC-M802 | Instruction Manual - Page 24
    01 format, such as from a GPS receiver, etc., is applied to [GPS] connector, your position and the UTC time should be input for DSC operation. IMPORTANT! The manually programmed position and the UTC time settings will be cleared once the power is turned OFF. They are never renewed during the voyage
  • Icom IC-M802 | Instruction Manual - Page 25
    6 Push and hold RX [DISTRESS] for 5 sec. 7 12.345.0 J3E GPS Lat 34 34'N SP Lon135 34'E 12:34 Exit DSC menu ******* DSC MENU ******* -------- Select -------- Position Individual Group All ships Position REQ ÇDistress Test RX memory TX memory Set up ÇExit SEL OK Distress
  • Icom IC-M802 | Instruction Manual - Page 26
    2182.0 kHz). • The DSC receiver circuit is still working to transceiver's microphone. • The acknowledgement is memorized into the RX memory channel. (p. 38) RX < ACK received > J3E GPS Lat 34 34'N SP Lon135 34'E 12:34 Exit t Activate an EPIRB (Emergency Position Indicating Radio
  • Icom IC-M802 | Instruction Manual - Page 27
    a distress call after selecting "Distress" in the DSC menu. q Push [DSC] to select DSC watch mode. w Push [MODE set] to select the DSC menu. [DSC] [MODE SET] [ENT] [CANCEL/CALL] station via the transceiver's microphone. • The acknowledgement is memorized into the RX memory channel. (p. 38) 19
  • Icom IC-M802 | Instruction Manual - Page 28
    " • "This is ..... (your ship name)." • The 9-digit identity AND the call sign (or other identification of the ship) • The ship's position if the DSC distress does not included it. • The nature of the distress and assistance required. • Any other information which might facilitate the rescue. 20
  • Icom IC-M802 | Instruction Manual - Page 29
    DSC MENU ******* -------- Select -------- Position ÇIndividual Group All ships Position REQ Distress Test RX memory TX memory Set up Exit SEL OK Address ID selection ****** Individual ****** ------ Address ID ------ ÇManual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802
  • Icom IC-M802 | Instruction Manual - Page 30
    the desired pre-programmed ID, or "Manual set," then push [ENT]. ✔When pre-programmed ID is selected, go to step u. ****** Individual ****** ------ Address ID ------ ÇManual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802-3 123456787 IC-M802-4 123456786 IC-M802-5 123456785 SEL OK
  • Icom IC-M802 | Instruction Manual - Page 31
    M802 has DSC TX memory. You can store often used DSC calling conditions for quick and simple re-call. Up to 10 conditions can be stored into the memory with the following instructions again to store the condition into the selected memory channel. ****** Individual ****** --- TX memory write ----
  • Icom IC-M802 | Instruction Manual - Page 32
    ." D Operation outline DSC menu ******* DSC MENU ******* -------- Select Manual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802-3 123456787 IC-M802-4 123456786 IC-M802-5 123456785 SEL OK Manual store the condition into the TX memory channel. ****** All ships ******* ****** Individual
  • Icom IC-M802 | Instruction Manual - Page 33
    SET] to select the DSC menu. w Rotate [ programmed frequencies or "Manual set" then push [ENT]. ✔ When a pre-programmed Manual set i Announce the following message. • "PAN PAN" T: 4567.0kHz IC-M802-1 R: 4567.0kHz T:12345.0kHz IC-M802 ] to select the desired calling channel, then push [ENT]. ******
  • Icom IC-M802 | Instruction Manual - Page 34
    ID code when the desired ship's ID is pre-programmed. ****** Individual ****** ------ Address ID ------ ÇManual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802-3 123456787 IC-M802-4 123456786 IC-M802-5 123456785 SEL OK • Select "Manual set" with [CH] then push [ENT], after that, enter
  • Icom IC-M802 | Instruction Manual - Page 35
    the called station is able to comply to the call. - to return to DSC watch mode when unable. * Individual ACK * * IC-M802 * * Able to comply * Exit * Individual ACK * * IC-M802 * * Unable to comply * * Operator unavailable * Exit When the called station is unable
  • Icom IC-M802 | Instruction Manual - Page 36
    D Operation outline DSC menu ******* DSC MENU ******* -------- Manual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802-3 123456787 IC-M802-4 123456786 IC-M802-5 123456785 SEL OK Manual store the condition into the TX memory channel. ****** All ships ******* ****** Individual ******
  • Icom IC-M802 | Instruction Manual - Page 37
    DSC format from "Individual" and "All ships," then push [ENT]. • When selecting "All ships" e Rotate [CH] to select "Urgency," then push [ENT]. y Rotate [CH] to select the desired calling channel programmed frequency is selected, go to step y. ****** All ships ******* -- Traffic frequency --ÇManual
  • Icom IC-M802 | Instruction Manual - Page 38
    ID code when the desired ship's ID is pre-programmed. ****** Individual ****** ------ Address ID ------ ÇManual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802-3 123456787 IC-M802-4 123456786 IC-M802-5 123456785 SEL OK • Select "Manual set" with [CH] then push [ENT], after that, enter
  • Icom IC-M802 | Instruction Manual - Page 39
    the called station is able to comply to the call. - to return to DSC watch mode when unable. * Individual ACK * * IC-M802 * * Able to comply * Exit * Individual ACK * * IC-M802 * * Unable to comply * * Operator unavailable * Exit When the called station is unable
  • Icom IC-M802 | Instruction Manual - Page 40
    category. q Push [MODE SET] to select the DSC menu. w Rotate [CH] to select "Individual" programmed. ****** Individual ****** ------ Address ID ------ ÇManual set IC-M802-1 123456789 IC-M802-2 123456788 IC-M802-3 123456787 IC-M802-4 123456786 IC-M802-5 123456785 SEL OK • Select "Manual
  • Icom IC-M802 | Instruction Manual - Page 41
    called station is able to comply to the call. - to return to DSC watch mode when unable. * Individual ACK * * IC-M802 * * Able to comply * Exit * Individual ACK * * IC-M802 * * Unable to comply * * Operator unavailable * Exit When the called station is unable
  • Icom IC-M802 | Instruction Manual - Page 42
    , then push [ENT]. • One of the voice channel, such as Tx/Rx: 2082.5 kHz, 4146.0 kHz, should be used. ********* Group Traffic frequency --- TX:_2134.0kHz RX:_2134.0kHz SEL OK y Rotate [CH] to select the desired pre-programmed calling frequency, or "Manual set" then push [ENT]. ✔ When the pre
  • Icom IC-M802 | Instruction Manual - Page 43
    q Push [MODE SET] to select the DSC menu. w Rotate [CH] to select programmed traffic frequency is selected, go to step y. ***** Position REQ ***** ---- Call frequency ---ÇManual set T: 2345.0kHz R: 2345.0kHz T: 2177.0kHz R: 2177.0kHz SEL OK IC-M802-1 SHIP * Position ACK * * IC-M802
  • Icom IC-M802 | Instruction Manual - Page 44
    select the DSC menu. w Rotate [CH] to select "Test" call, then push [ENT]. e Select the desired coast station code, then push [ENT]. • Use [CH] to select the coast station code when pre-programmed. ********* Test Address ID -----ÇManual set Port ICOM 001234567 Port ABC 001234566 Port M802 001234565
  • Icom IC-M802 | Instruction Manual - Page 45
    DSC watch mode to decode these calls. • Transmit an acknowledgement When the following DSC is received, an acknowledgement must be sent back to the calling station. •Short beeps, or an emergency alarm sounds until pushing [CANCEL/CALL], depending on the category. * Individual * * ICOM M802
  • Icom IC-M802 | Instruction Manual - Page 46
    Traffic:J3E TX 2182.0kHz RX 2182.0kHz RX Freq:TX 2187.5kHz RX 2187.5kHz DEL Cancel OK t Push [MODE SET] to return to DSC watch mode. I Deleting a memory ➥ When the desired memory contents to be deleted are displayed as at right, push and hold [CE] for 1 sec. • After erasing
  • Icom IC-M802 | Instruction Manual - Page 47
    station to the ship in distress. RX < Traffic > J3E GPS Lat 34 34'N SP Lon135 34'E 12:34 Exit r Select the received distress call memory channel to check the position of the ship in distress. ➥ Push [FREQ/CH] then [RX CLAR] to select "RX memory" screen. ➥Select "Distress" with [CH] then
  • Icom IC-M802 | Instruction Manual - Page 48
    require any action on your part. I Group call q When receiving an Group call, beeps may sound and "Group" is displayed as below. • Push [CANCEL/CALL] to stop the alarm when an emergency or urgency group call is received. * Group * * ICOM M802 * Exit Traffic Calling station's name
  • Icom IC-M802 | Instruction Manual - Page 49
    * * ICOM M802 * Exit ACK ------ Category:Routine From:ICOM M802 Traffic:J3E TX 2345.0kHz Individual ACK Call --------Category:Routine To:ICOM M802 Traffic:J3E TX 2345.0kHz RX 2345 "Able" and "Unable," then To:ICOM M802 Unable to comply 8 push [ENT given Busy Channel unable Mode
  • Icom IC-M802 | Instruction Manual - Page 50
    :34 Null OK r Push and hold [CANCEL/CALL] 1 sec. to transmit the Position request acknowledgement. • Returns to DSC watch mode after the transmission, automatically ***** Position ACK Call --------To:ICOM M802 Position:Lat 34 34'N Lon134 34'W UTC 12:34 Call Freq:TX 12345.0kHz RX 12345.0kHz Call
  • Icom IC-M802 | Instruction Manual - Page 51
    description The IC-M802 has several kinds of memories as follows: • Address and group ID code memories (p. 44) • Call, traffic and scan frequency memories. (p. 45) • DSC transmission memory (described in this section) • Received message memory (p. 38) 10 DSC transmission memory channels allow you to
  • Icom IC-M802 | Instruction Manual - Page 52
    automatically. •The ID list is displayed in alphabetical order for ID name, so [CH] rotation may be necessary for the programmed ID confirmation. ******** Set up Address ID Set up Group ID ------Ç ICOM M802 012345678 SEL C an c e l OK y Push [MODE SET] to return to DSC watch mode, or
  • Icom IC-M802 | Instruction Manual - Page 53
    [ENT] to program the contents into a all, traffic or scan frequency. • Returns to the call/traffic/scan frequency list screen. • The programmed frequency is displayed at ---Ç T: 4567.0kHz ICOM Group R: 4567.0kHz SEL C an c e l OK y Push [MODE SET] to return to DSC watch mode, or push [FREQ
  • Icom IC-M802 | Instruction Manual - Page 54
    then push [ENT]. • Push [DSC] to select DSC watch mode. • Push [MODE SET] to select DSC menu. • Rotate [CH] to select "Set up" then push [ENT]. w Rotate [CH] to select the desired memory, then push [ENT]. ******** Set up Address ID Set up Group ID ------- Name:ICOM M802 ID:012345678 TX: 2345
  • Icom IC-M802 | Instruction Manual - Page 55
    operation mode by pushing [DSC] in advance. • Pushing [Y]/[Z] on the microphone also selects the channel. • [GRP] rotation changes in 20-channel increments. • Selectable e-mail frequencies may differ according to your provider. r Follow the e-mail application instruction for e-mail reception and
  • Icom IC-M802 | Instruction Manual - Page 56
    selection ✔ This item appears when e-mail mode is selected before entering quick set mode. Selects the IF filter passband width for independent e-mail channel operation from WIDE (2.8 kHz; default), MIDDLE (2.4 kHz) and NARROW (500 Hz). 48 [F] [MODE SET] [GRP] [CH] ITEM SEL ITEM SEL ITEM SEL
  • Icom IC-M802 | Instruction Manual - Page 57
    for programming channels are in- hibited. (default: OFF) *** SET MODE *** ÇÇ O F F ON ITEM SEL External antenna tuner type This item selects the connected Icom antenna antenna tuner is connected, tuning can be started automatically without pushing [TUNE THRU], for instant operation. If manual
  • Icom IC-M802 | Instruction Manual - Page 58
    following scan functions. Programmed scan searches signals within the frequency range and activates slowly while squelch is open and fast while squelch is closed. Channel scan and channel resume scan searches 20 channels around a user selected channel, or searches all ITU channels in the band
  • Icom IC-M802 | Instruction Manual - Page 59
    you to mute receiving until keying stops with some delay time. (default: FULL) Microphone keys This item activates/deactivates the keys on the HM135 HAND MICROPHONE ([P], [∫] and [√]). Refer below on how to program the [P] key. (default: ON) [P] key function This item assigns a function to the
  • Icom IC-M802 | Instruction Manual - Page 60
    12 SET MODE D Initial set mode items (continued) REMOTE ID This item selects the ID for the transceiver from 1 to 99. (default: 08) REMOTE connector interface This item selects the interface format for [REMOTE] connector. (default: NMEA) Modulation input/output selection This item selects
  • Icom IC-M802 | Instruction Manual - Page 61
    INSTALLATION I Supplied accessories The following accessories are supplied with IC-M802. q Microphone modem, NBDP (Narrow Band Direct Printing), or FAX systems Personal computer (when e-mail modem is the PC is operated. This time can be programmed by your dealer. The default inhibit time is
  • Icom IC-M802 | Instruction Manual - Page 62
    INSTALLATION I Rear panel connections Optional AT-140 HF antenna (for DSC reception) Grounding (see pgs. 55, 63-65) Grounding (see pgs. 55, 63-65) OPC-1147 (10 m; 32.8 ft) CAUTION: • After connecting the antenna may be helpful. q Install the cable tie (base) onto the IC-M802 main unit side panel,
  • Icom IC-M802 | Instruction Manual - Page 63
    tuner MUST have an adequate RF ground connection. Otherwise, the overall efficiency of the transceiver and antenna tuner installation will be reduced. Electrolysis, electrical shocks and interference from other equipment could also occur. For best results, use 50 or 75 mm (2 or 3 inches) wide
  • Icom IC-M802 | Instruction Manual - Page 64
    or transmitting. D MN-100/MN-100L ANTENNA MATCHERS With a 50 Ω matched antenna all marine bands cannot be used. The following antenna matcher or antenna tuner may be helpful for antenna installation. Antenna wire MN-100/MN-100L When the antenna used for DSC reception. D AT-130/AT-130E AUTOMATIC
  • Icom IC-M802 | Instruction Manual - Page 65
    should be at 90 degrees to your line of sight when operating it. CAUTION: KEEP the transceiver and microphone at least 1 meter away from your ship's magnetic navigation compass. Check the installation angle; the display may not be easy to read at some angles. D Mounting the controller/speaker/main
  • Icom IC-M802 | Instruction Manual - Page 66
    speaker through the hole as shown below. CAUTION: KEEP the transceiver and microphone at least 1 meter away from your ship's magnetic navigation compass. mm (1 in) space between them into the instrument panel. w Install the speaker as instructed above, first. e Attach the screw and spacer on the
  • Icom IC-M802 | Instruction Manual - Page 67
    I Transceiver dimensions 220 mm; 8 21⁄32″ 13 CONFECTION AND INSTALLATION 84;.435m⁄16m″ 110 mm; 411⁄32″ 120 mm ; 423⁄32″ 290 mm; 11 13⁄32″ 290 mm; 1113 ⁄32″ 8;43.54⁄1m6″m 110 mm; 411⁄32″ 110 mm; 411⁄32″ 13 59
  • Icom IC-M802 | Instruction Manual - Page 68
    13 CONFECTION AND INSTALLATION I Fuse replacement The transceiver has 2 fuses (2 types) to protect internal circuitry, 1 fuse for the fuse holder on the DC power cable and 1 for inside. If
  • Icom IC-M802 | Instruction Manual - Page 69
    13 CONFECTION AND INSTALLATION I Connector information ACC Pin Pin name Description 1 CWK CW Output current : max. 1 A Control voltage : -3 to 0 V Input impedance : More than 10 kΩ MICROPHONE Pin Pin name Description 1 MIC+ Audio input from the mic element. 2 NC No connection qu wiy ert
  • Icom IC-M802 | Instruction Manual - Page 70
    13 CONFECTION AND INSTALLATION I Connector information (continued) AF/MOD 5 1 9 6 Pin Pin name Description 1 MOD+ Modulation input from an external terminal unit. 2 MOD- Coaxial ground for NMD+. 3 GND Ground for
  • Icom IC-M802 | Instruction Manual - Page 71
    weather gear and the like. The tuner interconnects with the Icom SSB. Full details are in the tuner instruction (installation) manual install your sideband system, have him skip this part and begin reading at "Antenna Ground Principles, Technically Speaking." If you plan to do the installation radio
  • Icom IC-M802 | Instruction Manual - Page 72
    radio reception when someone broke off your whip antenna? The same degradation of range also takes place when there is little or no RF ground system for antenna to work against in a marine installation OCCURRENCES. SURFACE AREA For marine SSB radios a good radio frequency ground system will consist
  • Icom IC-M802 | Instruction Manual - Page 73
    from the below waterline ground system. Most manufacturers of Loran weather fax and marine single sideband sets don't provide an easy way problems you will have with stray RF. The ground foil must also run to remote tuners. This includes the tuner on your Loran antenna set-up as well as the ICOM
  • Icom IC-M802 | Instruction Manual - Page 74
    J3E (USB/LSB), H3E,* J2B (AFSK), F1B (FSK), A1A (CW) DSC receiver J2B *Receive only • No. of memory Ch. : 1136 channels (max.) 160 user programmable, 242 ITU SSB duplex, 72 ITU SSB simplex, 662 ITU FSK duplex channels • Antenna connector : SO-239×2 (50 Ω) • Usable temp. range : -30˚C to
  • Icom IC-M802 | Instruction Manual - Page 75
    I Remote controller (RC-25) 92 mm; 35⁄8″ 16 TEMPLATE 4-R11 204 mm; 81⁄32″ 15 16 67
  • Icom IC-M802 | Instruction Manual - Page 76
    I Speaker (SP-24) TEMPLATE 16 92 mm; 35⁄8″ 4-R11 92 mm; 35⁄8″ 16 69
  • Icom IC-M802 | Instruction Manual - Page 77
    ANTENNA TUNER AT-140 AUTOMATIC ANTENNA TUNER PS-60 DC POWER SUPPLY Matches the transceiver to a long wire antenna with a minimum of insertion loss. Antenna and control cable receptacles for easy installation 24 to a panel. HM-135 HAND MICROPHONE OPC-1147 SHIELDED CONTROL CABLE Shielded control
  • Icom IC-M802 | Instruction Manual - Page 78
    . 2380 116th Avenue N.E., Bellevue, WA 98004, U.S.A. Phone: (425) 454-8155 Fax: (425) 454-7619 URL: http//www.icomamerica.com Phone: (425) 454-7619 Icom (Europe) GmbH Communication Equipment Himmelgeister Str. 100, D-40255 Düsseldorf, Germany Phone: 0211
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
MF/HF MARINE TRANSCEIVER
iM802
INSTRUCTION MANUAL