Icom ID-5100A Full Instruction Manual
Icom ID-5100A Manual
 |
View all Icom ID-5100A manuals
Add to My Manuals
Save this manual to your list of manuals |
Icom ID-5100A manual content summary:
- Icom ID-5100A | Full Instruction Manual - Page 1
FULL MANUAL DUAL BAND TRANSCEIVER ID-5100A ID-5100E To update the repeater list, click here! INTRODUCTION 1 PANEL DESCRIPTION 2 BASIC OPERATION 3 MEMORY OPERATION 4 SCAN OPERATION 5 PRIORITY WATCH 6 D-STAR OPERATION 7 D-STAR OPERATION 8 GPS OPERATION 9 USING AN SD CARD 10 VOICE - Icom ID-5100A | Full Instruction Manual - Page 2
CS-5100 cloning software) Microphone hanger Instruction manual [Basic Manual] IMPORTANT READ ALL INSTRUCTIONS carefully and com- pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL- This instruction manual contains full operating instructions for the ID-5100A/ID-5100E. Icom, Icom - Icom ID-5100A | Full Instruction Manual - Page 3
instruc- tions that are in this manual • Cloning Software Installer Installer for the CS-5100 cloning software • Cloning Software Instruction manual Instructions for the CS-5100 cloning software installa- tion and use • Operating Guide Operating guide for using the touch screen, Menu items and - Icom ID-5100A | Full Instruction Manual - Page 4
the date and time: Stops recording: • This icon appears while recording. Displays the GPS menu window: Sets MAIN band to the right side: Dual or Single band display selection: • In the Single band, touch [B] to set the B band as the MAIN band. Sets MAIN band to the right side: ID-5100 Function - Icom ID-5100A | Full Instruction Manual - Page 5
of Adobe® Reader® The following functions and features can be used with Adobe® Reader®. • Keyword search Click "Find (Ctrl *The printing setup may differ, depending on the printer. Refer to your printer's instruction manual for details. *Select "A4" size to print out the page in the equalized - Icom ID-5100A | Full Instruction Manual - Page 6
Previous view INTRODUCTION About these Advanced Instructions (PDF format) These Advanced Instructions describe the details of the ID-5100A/E features. This PDF formatted manual provides you with convenient functions, as follows. NOTE: Below page is used only as an example to describe these advanced - Icom ID-5100A | Full Instruction Manual - Page 7
Previous view Section 1 PANEL DESCRIPTION Controller - Front panel 1-2 Controller - Display (Touch screen 1-3 DDFunction menu 1-5 Main unit - Front and rear panels 1-7 DDMicrophone connector information 1-7 Microphone (HM-207 1-8 DDSetting frequency and Memory channel 1-9 1-1 - Icom ID-5100A | Full Instruction Manual - Page 8
ID-5100 w w e t r r yui o q SQUELCH CONTROL [SQL] Rotate to adjust the squelch level. (p. 2-2, p.4-3) • Normally, set the squelch level to where noise and the "BUSY" icon just disappear. (closed) • You can use controller to the Main unit using the sup- plied control cable. (p. 1-7) r TUNING - Icom ID-5100A | Full Instruction Manual - Page 9
ON. ➥➥"CSQL" is displayed while the Digital Code squelch function is ON. t Bluetooth® ICON (p. 15-6, p. 15-14) Displayed when you make a Bluetooth® connection between your transceiver that has the optional UT133 Bluetooth® unit installed and a Bluetooth® device. y VOX ICON (p. 15-8) Displayed - Icom ID-5100A | Full Instruction Manual - Page 10
band) Single watch mode (B band) @0 !9 !8 !7 !6 !5 This side becomes the A band This side becomes the B band in the Single watch mode in the Single watch mode !3 DR SCREEN Displays the DR screen where the D-STAR • "PSKIP": Program skip !6 MEMORY CHANNEL the USA version transceiver. !7 MEMORY - Icom ID-5100A | Full Instruction Manual - Page 11
transceiver, depending on the transceiver's operating mode or status. Each function key works for the MAIN band DR screen, touch for 1 second to store the operating data into the blank channel. ➥➥In the Memory or Call used scan. @0 [MONI] Touch to turn the Digital Monitor function ON or OFF. 1-5 - Icom ID-5100A | Full Instruction Manual - Page 12
!0 @1 [SKIP] ➥➥Touch to open the skip setting window for the Access repeater scan. ➥➥Touch for 1 second to set the skip setting in the Function menu. e @2 !3 @2 [DSQL] (Appears in the DV mode.) Touch to open the Digital squelch function setting window. If you set the operating mode to "DV - Icom ID-5100A | Full Instruction Manual - Page 13
of the transceiver. • Use for the transceive function with another Icom CI-V transceiver or receiver. When the transceive function is set to ON, changing the frequency, operating mode and so on, on the ID-5100A/E automatically changes those settings on other Icom transceivers or receivers - Icom ID-5100A | Full Instruction Manual - Page 14
channel. e [PTT] SWITCH Hold down to transmit, release to receive. r [VFO/MR• ] KEY ➥➥Push [F-1] key. (Default: D uring RX/Standby: [BAND/BANK] During TX: [T-CALL]) [F-2] KEY Push the number, push to set. !0 LED 2 Lights green when transceiver's power is ON. !1 [VOL∫/A] KEY ➥➥Push to increase - Icom ID-5100A | Full Instruction Manual - Page 15
Previous view 1 PANEL DESCRIPTION Microphone (HM-207) (Continued) DDSetting frequency and Memory channel [Example for frequency setting] First, push [VFO/MR• ] to select the VFO mode. To enter the 435.680 MHz frequency: ➥➥Push [4], [3], [5], [6], [8], [0], then [ENT]. To change the 435.680 MHz to - Icom ID-5100A | Full Instruction Manual - Page 16
Mode and the DR function 2-9 DDVFO/Memory/Call channel/Weather channel* mode 2-9 DDDR (D-STAR Repeater) function selection 2-10 Receiving 2-11 Transmitting 2-12 DDTransmitting on an Amateur band 2-12 DDSettings for the transmission 2-12 DDAbout transmit power levels and RF meter 2-12 Lock - Icom ID-5100A | Full Instruction Manual - Page 17
[SQL] clockwise makes the squelch tight. The tight squelch is for strong signals. • When rotating [SQL] clockwise beyond the center position, [SQL] can be used as 'S-meter Squelch' or 'Attenuator.' Select the [SQL] option in the Menu screen. (p. 12-52) [VOL] [SQL] [VOL] [SQL] ➥➥To mute the audio - Icom ID-5100A | Full Instruction Manual - Page 18
Previous view 2 BASIC OPERATION Selecting the watch mode The transceiver has two independent watch modes; Dualwatch mode and Single watch mode. Dualwatch mode The Dualwatch mode uses the MAIN and SUB bands, and you can simultaneously monitor both bands. In the Dualwatch mode, both MAIN and SUB - Icom ID-5100A | Full Instruction Manual - Page 19
to 550.000 MHz The ranges may differ, depending on the transceiver version. wwTouch [VFO]. • Selects the VFO mode. eeTouch the MHz digits. • Opens the operating band setting window. rrTouch the desired operating band. • The operating band setting window disappears. • Touch [F-INP] to open the - Icom ID-5100A | Full Instruction Manual - Page 20
displayed to the left. Then the next entered digit is displayed to the right of the previously entered digit. • If desired, touch "CE" to delete the entry. wwTouch [VFO]. • Selects the VFO mode. eeTouch the MHz digits. • Opens the operating band setting window. yyTouch [ENT] to set the frequency - Icom ID-5100A | Full Instruction Manual - Page 21
The VFO scan uses this step to search for a signal. Tuning steps (kHz) 5 6.25 8.33* 10 12.5 15 20 25 30 50 Auto* *Appears only when the AIR band is selected. In the AIR band, you can select only "8.33k", "25k" and "Auto." DDTuning step selection qqTouch the kHz digits for 1 second. • Opens - Icom ID-5100A | Full Instruction Manual - Page 22
for 1 second. • Displays the 1 MHz Quick Tuning icon. • "√" appears above the 1 MHz digit. Selecting a Squelch delay You can select a squelch delay in the Menu screen to prevent repeated opening and closing of the squelch while receiving the same signal. qqTouch [MENU]. wwTouch "Squelch Delay - Icom ID-5100A | Full Instruction Manual - Page 23
determined by the modulation of the radio signals. The transceiver has a total of five operating modes; AM, AM or AM-N mode for only the AIR band (118.000 MHz to 136.99166 MHz). • You can select to manually open the squelch, even when mute functions as the tone squelch or digital squelch are in use. - Icom ID-5100A | Full Instruction Manual - Page 24
. Weather channel mode* The Weather channel mode is used to monitor weather channels from the NOAA (National Oceanographic and Atmospheric Administration) broadcasts. *Selectable in only the U.S.A. version transceivers. wwSelect the desired Mode. ➥➥Touch [VFO] to select the VFO mode. ➥➥Touch - Icom ID-5100A | Full Instruction Manual - Page 25
BASIC OPERATION Selecting the Mode and the DR function (Continued) DDDR (D-STAR Repeater) function selection The DR (D-STAR Repeater) function is for D-STAR repeater operation. In this mode, you can easily select the preprogrammed repeaters and UR call signs by rotating [DIAL]. See page 6-4 for the - Icom ID-5100A | Full Instruction Manual - Page 26
the Memory channel number. • Opens the Mode setting window. wwTouch [VFO]. • Selects the VFO mode. eeTouch the MHz digits. • Opens the operating band setting window. rrTouch [144]. ttTouch the Mode icon. • Opens the operating mode setting window. yyTouch a desired operating mode. uuRotate - Icom ID-5100A | Full Instruction Manual - Page 27
to other stations on the same frequency. CAUTION: Transmitting without an antenna may damage the transceiver. You can transmit on only the 144 MHz and 430 MHz bands. NOTE: • If the MAIN band frequency is a multiple of the SUB band frequency, you might receive a very small signal on the SUB - Icom ID-5100A | Full Instruction Manual - Page 28
Lock function, touch [OFF] in the "LOCK" dialog box. • You can still use [ ], [PTT], [SQL] and [VOL], and [MAIN DIAL], [F-2](Monitor) on the supplied microphone while the Lock function is ON. Attenuator function The transceiver has an RF attenuator related to the squelch control setting. You can - Icom ID-5100A | Full Instruction Manual - Page 29
Band Scope function has two sweep types, Single sweep and Continuous sweep: • A Single sweep searches the specified frequency range only once. • A Continuous sweep repeatedly searches the speci- fied frequency range. The transceiver to 20 kHz or less to use the Band Scope function. See page 2-6 for - Icom ID-5100A | Full Instruction Manual - Page 30
the audio output may be interrupted when the frequency is changed while scanning, or by other factors. Example: MAIN band is in the FM mode. SUB band is in the DV mode. MAIN band SUB band Microphone gain level setting Set the microphone gain level in the Menu screen. qqTouch [MENU]. wwTouch "MIC - Icom ID-5100A | Full Instruction Manual - Page 31
2 BASIC OPERATION Home channel function Home channels are often-used frequencies you can preset in the transceiver's VFO mode, Memory mode and DR function. Select the Channel." or while in the DR screen, touch "Set Repeater." Touching "Clear" in step r described above clears the Home channel. 2-16 - Icom ID-5100A | Full Instruction Manual - Page 32
the displayed frequency and operating mode in the VFO, Memory or Call channel modes, or the call sign of the DR function. Also, you can use other speech functions, such as the [DIAL] speech function and Mode speech function. NOTE: When you push [ ](SPEECH) while recording the received audio in the - Icom ID-5100A | Full Instruction Manual - Page 33
Previous view Section 3 MEMORY OPERATION General description 3-2 DDThe number of the Memory channel 3-2 DDMemory channel content 3-2 Manage Memory screen description 3-3 DDTree view of the Manage Memory screen 3-3 DDEntering the Manage Memory screen 3-3 Selecting a Memory channel 3-4 - Icom ID-5100A | Full Instruction Manual - Page 34
, we recommend that you backup the memory content or save it to an SD card or to a PC. • The SD card is not available from Icom. Purchase an SD card to meet your needs. • The CS-5100 cloning software can also be used to backup your memory data. 3-2 - Icom ID-5100A | Full Instruction Manual - Page 35
Previous view 3 MEMORY OPERATION Manage Memory screen description The "MANAGE MEMORY" screen enables you to easily edit the Memory or Call channel content. • View the Memory or Call channel content on a list. • Easy to assign to a bank, and view the bank content on a list. • Easy to add, edit, - Icom ID-5100A | Full Instruction Manual - Page 36
Previous view 3 MEMORY OPERATION Selecting a Memory channel qqTouch the Memory channel number. • Opens the Mode setting window. wwTouch [MR]. • Selects the Memory mode. • Displays " " and the selected Memory channel number. Appears eeRotate [DIAL] to select a Memory channel. • Blank channels - Icom ID-5100A | Full Instruction Manual - Page 37
Previous view 3 MEMORY OPERATION Selecting a Call channel Two Call channels (C0/C1) are selectable in each of the 144 and 430 MHz bands. Factory default frequencies and operating modes are entered into the Call channels. Change these to suit your operating needs. qqTouch the Memory channel number. • - Icom ID-5100A | Full Instruction Manual - Page 38
Previous view 3 MEMORY OPERATION Writing into a Memory channel After setting a frequency in the VFO mode, you can write it into a Memory channel. When writing into a channel, you can select the destination channel between your desired channel or the lowest blank channel. Memory channels 002 to 999 - Icom ID-5100A | Full Instruction Manual - Page 39
Previous view 3 MEMORY OPERATION Writing into a Memory channel (Continued) DDOverwriting into the selected channel You can write a frequency into a pre-entered channel. Example: Writing 147.010 MHz into Memory channel 18. qqTouch the Memory channel number. • Opens the Mode setting window. wwTouch - Icom ID-5100A | Full Instruction Manual - Page 40
Previous view 3 MEMORY OPERATION Writing into a Memory channel (Continued) DDCopying Memory content to the VFO It is convenient when you want to operate on the frequency around the Memory or Call channel. qqTouch the Memory channel number. • Opens the Mode setting window. uuTouch [YES]. • Beeps - Icom ID-5100A | Full Instruction Manual - Page 41
Previous view 3 MEMORY OPERATION Writing into a Memory channel (Continued) DDCopying Memory content to another Memory channel You can copy the memory content to another Memory channel. qqTouch the Function group icon one or more times. • Selects the F-1 menu. wwTouch [MW]. uuTouch "Copy." • - Icom ID-5100A | Full Instruction Manual - Page 42
MEMORY OPERATION Memory bank setting The transceiver has a total of 26 banks (A to Z). Regular memory channels 0 to 999 are assignable to any desired bank for easy memory management. Up to 100 channels can be assigned to a bank. NOTE: The memory banks are only used to hold memory channels. Thus if - Icom ID-5100A | Full Instruction Manual - Page 43
way is a short cut to creating a memory channel, and then assigning it to a bank. In that case, the transceiver automatically selects the lowest blank memory channel, to program. Example: Writing 146.030 MHz into Bank A. qqTouch the Memory channel number. • Opens the Mode setting window. wwTouch - Icom ID-5100A | Full Instruction Manual - Page 44
Previous view 3 MEMORY OPERATION Memory bank setting (Continued) DDSelecting the Memory bank mode When you select the Memory bank mode, rotating [DIAL] selects only the entered bank channels in the selected bank. qqTouch the Memory channel number. • Opens the Mode setting window. wwTouch [MR]. • - Icom ID-5100A | Full Instruction Manual - Page 45
characters and symbols A to Z, a to z, 0 to 9 space) !0 Touch [] to move the cursor backwards, or touch [] to move the cursor forwards. !1 Repeat steps o and !0 to enter a name of up to 16 characters, including spaces. !2 After entering, touch [ENT]. !3 Touch "," and then touch - Icom ID-5100A | Full Instruction Manual - Page 46
Previous view 3 MEMORY OPERATION Entering a Memory or Bank name (Continued) DDEntering a Bank name qqTouch the Function group icon one or more times. • Selects the F-1 menu. wwTouch [MW]. eeTouch [Manage Memory]. • Open the "MANAGE MEMORY" screen. rrTouch "Memory CH." ttTouch a desired bank - Icom ID-5100A | Full Instruction Manual - Page 47
Previous view 3 MEMORY OPERATION Selecting a Memory name display The transceiver has three Memory name display types. qqSelects the Memory mode. wwTouch [QUICK]. eeTouch "Display Type." rrTouch the desired display type. • Freq ( - Icom ID-5100A | Full Instruction Manual - Page 48
Previous view 3 MEMORY OPERATION Clearing a Memory channel Entered memory content can be cleared (erased), if desired. qqTouch the Function group icon one or more times. • Selects the F-1 menu. wwTouch [MW]. eeTouch [Manage Memory]. • Open the "MANAGE MEMORY" screen. rrTouch the desired channel - Icom ID-5100A | Full Instruction Manual - Page 49
Previous view Section 4 SCAN OPERATION Scan 4-2 DDAbout the scan function 4-2 DDVFO scan 4-2 DDMemory scan 4-2 DDMemory bank scan 4-2 DD[DIAL] operation during a scan 4-3 DDSquelch setting for a scan 4-3 DDTuning step for a VFO scan 4-3 DDSkip function 4-3 DDTemporary Skip timer 4-3 - Icom ID-5100A | Full Instruction Manual - Page 50
(Full scan) p. 4-5 Repeatedly scans the entire band. 118 MHz 550 MHz P SKIP Scan P SKIP Jump • BAND (Selected band scan) p. 4-5 Scans all frequencies over the entire selected band. Band edge Band edge P SKIP Scan P SKIP Jump • PROG 0-24 (Program scan) p. 4-5 Scans the program scan edge - Icom ID-5100A | Full Instruction Manual - Page 51
be changed in the Menu screen. (p. 4-11) (Scan > Temporary Skip Timer) DDReceive mode during a scan • The selected mode is used by the scan. • During a memory or bank scan, the mode programmed into the channel is used by the scan. Scanning in the FM mode Blinks Blinks Displays the scan type 4-3 - Icom ID-5100A | Full Instruction Manual - Page 52
To manually resume the Program scan link channel. (p. 4-12) By selecting the scan name, the scanning frequency range will be set. The SUB band audio signal is muted. Example: While waiting for a DV signal on the MAIN band, the transceiver receives another signal from a DV repeater on the SUB band - Icom ID-5100A | Full Instruction Manual - Page 53
are not skipped during a scan. (Scan > Program Skip) DDVFO mode scan qqTouch the Memory channel number. • Opens the Mode setting window. wwTouch [VFO]. • Selects the VFO mode. eeTouch the MHz digits. • Opens the operating band setting window. rrTouch the desired operating band. ttTouch the Mode icon - Icom ID-5100A | Full Instruction Manual - Page 54
enter the scan name. NOTE: The scan name is not displayed during a scan. • When the scan name is assigned When a program link name is assigned. When a program link name is assigned, the program link name is displayed on the scan type setting window. (Step r on page 4-5) See page 12-16 to enter the - Icom ID-5100A | Full Instruction Manual - Page 55
channel into empty memory channel 999. • The entered memory channel number blinks. • If channel 999 already has content, the transceiver automatically searches for another blank channel to use. If no blank memory channel is found, a beep sounds, and no skip channel is set. rrTouch the Function - Icom ID-5100A | Full Instruction Manual - Page 56
Previous view 4 SCAN OPERATION Memory scan Repeatedly scans all programmed Memory channels. There two types of scans During a Memory scan Blinks ttTouch the desired scan type. • ALL: Full scan • BAND: Band memory scan • MODE: Mode memory scan • DUP: Duplex scan (p. 4-2) (Appears only when - Icom ID-5100A | Full Instruction Manual - Page 57
scan searches through the memory channels in the selected bank. • Two or more memory channels, which are not set as skip chan- nels, must be programmed to start a memory bank scan. • When the "Bank Select" item in the Quick Menu screen is set to "OFF," a bank scan is not started. qqTouch - Icom ID-5100A | Full Instruction Manual - Page 58
Previous view 4 SCAN OPERATION Setting and clearing the skip channel The channels set as "SKIP" or "PSKIP" skip channels are skipped (not scanned). See page 4-7 for details of clearing the skip setting. Example: Set "SKIP" to Memory channel "000." qqTouch the Memory channel number. • Opens the Mode - Icom ID-5100A | Full Instruction Manual - Page 59
Previous view 4 SCAN OPERATION Setting the temporary skip function This function temporarily skips up to five unwanted frequencies during a scan, for the set time period. This function enables you to temporarily skip the unwanted frequencies without the skip frequency setting. qqStart the scan. (p. - Icom ID-5100A | Full Instruction Manual - Page 60
transceiver's version. You can enter a total of up to 25 program scan edge ranges. qqTouch [MENU]. wwTouch "Program Scan Edge." (Scan > Program to move the cursor backwards, or touch [] to move the cursor forwards. ooRepeat steps o and !0 to enter a name of up to 16 characters, including spaces - Icom ID-5100A | Full Instruction Manual - Page 61
entered. !7 Touch "MODE." • Displays the selectable mode. !3 After entering a lower frequency, touch The cursor moves to a MHz digit of the higher frequency. !8 Touch the desired receive mode to be used while program scanning. • When you select "---," the receive mode set in the VFO mode is - Icom ID-5100A | Full Instruction Manual - Page 62
Previous view Section 5 PRIORITY WATCH Priority watch 5-2 DDVFO frequency and a priority channel 5-2 DDVFO frequency and a Memory/Bank scan 5-2 DDVFO scan and a priority channel 5-2 DDVFO scan and a Memory/Bank scan 5-2 DDA frequency in "FROM" on the DR screen and a priority channel 5-3 DDDR - Icom ID-5100A | Full Instruction Manual - Page 63
While in the Dualwatch mode, Priority watch can be activated on both the MAIN and SUB band. When the DV signal is simultaneously received on both MAIN and SUB band, the SUB band audio signal is muted. DDVFO scan and a priority channel (p. 5-8) Checks the selected priority channel every 5 seconds - Icom ID-5100A | Full Instruction Manual - Page 64
watch (Continued) DDA frequency in "FROM" on the DR screen and a priority channel (p. 5-12) Checks a priority channel every 5 seconds while receiving on a repeater or simplex frequency set in "FROM" on the DR screen. A VFO frequency, Memory channel, Bank channel or Call channel can be selected as - Icom ID-5100A | Full Instruction Manual - Page 65
Previous view 5 PRIORITY WATCH VFO frequency and a priority channel Checks the selected priority channel every 5 seconds, while receiving on a VFO frequency. 1. Set the VFO frequency q Touch the Memory channel number. • Opens the Mode setting window. w Touch [VFO]. e Set the receive frequency - Icom ID-5100A | Full Instruction Manual - Page 66
Previous view 5 PRIORITY WATCH VFO frequency and a priority channel (Continued) 4. During a Priority watch Checks the selected priority channel every 5 seconds, while receiving on a VFO frequency. Example: C hecks Memory channel "000" while receiving on 145.000 MHz. Appears Appears Priority - Icom ID-5100A | Full Instruction Manual - Page 67
Previous view 5 PRIORITY WATCH VFO frequency and a Memory/Bank scan Sequentially checks the Memory or Bank channels every 5 seconds, while receiving on a VFO frequency. 1. Set the VFO frequency q Touch the Memory channel number. • Opens the Mode setting window. w Touch [VFO]. e S et the - Icom ID-5100A | Full Instruction Manual - Page 68
Previous view 5 PRIORITY WATCH VFO frequency and a Memory/Bank scan (Continued) 4. During a Priority watch Sequentially checks the Memory or Bank channels every 5 seconds, while receiving on a VFO frequency. Example: Sequentially checks the Memory channels while receiving on 145.000 MHz. - Icom ID-5100A | Full Instruction Manual - Page 69
Previous view 5 PRIORITY WATCH VFO scan and a priority channel Checks the selected priority channel every 5 seconds, during a VFO mode scan. 1. Set the priority channel • To select a Memory channel q Touch the Memory channel number. • Opens the Mode setting window. w Touch [MR]. e R otate [DIAL - Icom ID-5100A | Full Instruction Manual - Page 70
Previous view 5 PRIORITY WATCH VFO scan and a priority channel (Continued) 4. During a Priority watch Checks the selected priority channel every 5 seconds, while VFO scanning. Example: Checks Memory channel "000" while VFO scanning Appears Appears Blinks Checks the Memory channel "000" every - Icom ID-5100A | Full Instruction Manual - Page 71
Previous view 5 PRIORITY WATCH VFO scan and a Memory/Bank scan Sequentially checks the Memory or Bank channels every 5 seconds during a VFO scan. 1. Start the Memory or Bank scan • To start a Memory scan q Touch the Memory channel number. • Opens the Mode setting window. w Touch [MR]. e T ouch - Icom ID-5100A | Full Instruction Manual - Page 72
Previous view 5 PRIORITY WATCH VFO scan and a Memory/Bank scan (Continued) 4. During a Priority watch Checks the selected priority channel every 5 seconds, while VFO scanning. Example: C hecks the Memory channels every 5 seconds while VFO scanning Appears Appears Blinks Example: Checks the - Icom ID-5100A | Full Instruction Manual - Page 73
channel number. • Opens the Mode setting window. w Touch [MR]. e R otate [DIAL] to select the Memory channel you want to watch. 2. Select the repeater or simplex frequency in the DR screen q T ouch [DR]. • Turns ON the DR function. w T ouch the "FROM" field. e R otate [DIAL] to select - Icom ID-5100A | Full Instruction Manual - Page 74
Previous view 5 PRIORITY WATCH A frequency in "FROM" on the DR screen and a priority channel (Continued) 3. Start a Priority watch q Touch [QUICK]. w T ouch "PRIO Watch." e T ouch "ON" or "Bell." • ON: When a signal is received on the priority channel, the channel is automatically selected. - Icom ID-5100A | Full Instruction Manual - Page 75
A frequency in "FROM" on the DR screen and a priority channel (Continued) 4. During a Priority watch Checks the selected priority channel every 5 seconds, while receiving on a repeater or a simplex frequency in the DR screen. Example: C hecks the VFO frequency every 5 seconds while receiving on - Icom ID-5100A | Full Instruction Manual - Page 76
Previous view 5 PRIORITY WATCH A frequency in "FROM" on the DR screen and a priority channel (Continued) 5. When a signal is received. • W hen "ON" is selected. When a signal is received on the priority channel, the channel is automatically selected. The "PRIO" icon blinks. * The scan pause - Icom ID-5100A | Full Instruction Manual - Page 77
Previous view 5 PRIORITY WATCH DR scan and a priority channel Checks the selected priority channel every 5 seconds, during a DR scan. 1. Set the priority channel • To select a VFO frequency q Touch the Memory channel number. • Opens the Mode setting window. w Touch [VFO]. e S et the receive - Icom ID-5100A | Full Instruction Manual - Page 78
Previous view 5 PRIORITY WATCH DR scan and a priority channel (Continued) 3. Start the Priority watch q Touch [QUICK]. w T ouch "PRIO Watch." e T ouch "ON" or "Bell." • ON: When a signal is received on the priority channel, the channel is automatically selected. • Bell: W hen a signal is - Icom ID-5100A | Full Instruction Manual - Page 79
Previous view 5 PRIORITY WATCH DR scan and a priority channel (Continued) 4. During a Priority watch Checks the selected priority channel every 5 seconds, during a DR scan. Example: C hecks the VFO frequency during the DR scan. Appears Appears Blinks Checks the VFO frequency every 5 seconds. - Icom ID-5100A | Full Instruction Manual - Page 80
Previous view 5 PRIORITY WATCH DR scan and a priority channel (Continued) 5. When a signal is received. • W hen "ON" is selected. When a signal is received on the priority channel, the channel is automatically selected. The "PRIO" icon blinks. * The scan pause timer and resume settings are the - Icom ID-5100A | Full Instruction Manual - Page 81
Previous view Section 6 D-STAR OPERATION IMPORTANT! • T he repeater list, described in this manual, may differ from your transceiver's preloaded contents. • A lthough Japanese repeaters are used in the setting examples, the Japanese repeater node (port) letters are different from other - Icom ID-5100A | Full Instruction Manual - Page 82
OPERATION Unique features of D-STAR ●● Easy Cross band operation through the repeater ●● Easy call sign entry with the Repeater list or TX/RX History 1200 MHz 430 MHz You can communicate with a 1200 MHz D-STAR station using the ID-5100A/E! Easy Destination (TO) setting! ●● Call Sign - Icom ID-5100A | Full Instruction Manual - Page 83
can transmit and receive digital voice, including low-speed data, at the same time. You can transmit and receive position data from the built-in GPS receiver. About the DR (D-STAR Repeater) function You can easily use the D-STAR repeaters with the DR (D-STAR Repeater) function. With this function - Icom ID-5100A | Full Instruction Manual - Page 84
• Before operating in the duplex mode, be sure to check whether the repeater is busy, or not. If the repeater is busy, wait until it is clear, or ask for a "break" using a method acceptable to your local procedures. • The transceiver has a Time-Out Timer function for DV operation. The timer limits - Icom ID-5100A | Full Instruction Manual - Page 85
transceiver Before starting D-STAR, registering your call sign (MY) and entering your D-STAR ttTouch the desired keypad to select the first digit. (Example: J). • A to Z, 0 to touch [] to move the cursor forwards. uuRepeat steps t and y to enter your call . (p. 6-7) Keys used for entry Moves the - Icom ID-5100A | Full Instruction Manual - Page 86
! If desired, enter a note of up to 4 characters, such as the model of the transceiver, name, area name, and so on, after your call sign. qqTouch [] one or more times until the cursor moves to the right of the "/". wwRepeat steps t and y on the page 6-5 to enter a 4 character note. (Example - Icom ID-5100A | Full Instruction Manual - Page 87
of them, contact the administrator of a repeater that uses the alternate system. 1. Access the call sign registration screen STAR Gateway System" screen appears. Click [Register] to start the New User registration. If needed, ask the gateway repeater administrator for call sign registration instructions - Icom ID-5100A | Full Instruction Manual - Page 88
Previous view 6 D-STAR OPERATION Making a Simplex call You can make a transceiver to transceiver call (through no repeater) in the DR screen. NOTE: Depending on the transceiver's version, the frequencies may be different. Check for acceptable frequencies for your operating area. ✓✓ What is - Icom ID-5100A | Full Instruction Manual - Page 89
. If your call sign (MY) has not been set, or your call sign and equipment have not been registered at a D-STAR repeater, see page 6-5 to 6-7. 1. Select your Access repeater ("FROM") qqTouch [DR]. wwCheck whether or not "FROM" is selected. • If "FROM" is not selected, touch the "FROM" field. eeTouch - Icom ID-5100A | Full Instruction Manual - Page 90
6 D-STAR OPERATION Accessing repeaters (Continued) 3. Check whether you can access the repeater !2 H old down [PTT] for approximately 1 second to ac- cess the repeater. !3 If you get a reply call, or "UR?" appears on the LCD within 3 seconds, your signal reached your access repeater and - Icom ID-5100A | Full Instruction Manual - Page 91
STAR OPERATION Using the RX history When a DV call is received, the call signs of the caller, the called station and the called station's access repeater of the MAIN band. The second page or later displays the record according to the received date and time, regardless of the band it was - Icom ID-5100A | Full Instruction Manual - Page 92
Previous view 6 D-STAR OPERATION Capturing a call sign After you receive a repeater's signal, the calling station's call sign can be captured by touching the Call Sign Capture key ([RX>CS]) for 1 second. Then you can quickly and - Icom ID-5100A | Full Instruction Manual - Page 93
the microphone lights red. yyTouch your access repeater. (Example: "Hirano") • Returns to the DR screen, and the selected repeater name is displayed in "FROM." For your reference: The Local CQ call is used to call anyone, but you can call a specific station by simply saying their call sign. 6-13 - Icom ID-5100A | Full Instruction Manual - Page 94
• Returns to the DR screen, and the selected repeater name is displayed in "TO." 3. Hold down [PTT] to transmit • The LED1 on the microphone lights red. For your reference: The Gateway CQ call is used to call any repeater, but you can call a specific station by simply saying their call sign. 6-14 - Icom ID-5100A | Full Instruction Manual - Page 95
that the station accessed. So, even if you don't know where the station is, you can make a call using call sign routing. 1. Set "FROM" (Access repeater) qqTouch [DR]. wwCheck whether or not "FROM" is selected. • If "FROM" is not selected, touch the "FROM" field. eeTouch the "FROM" field. • Opens - Icom ID-5100A | Full Instruction Manual - Page 96
view 6 D-STAR OPERATION Troubleshooting To communicate through the repeater, your signal must access to the repeater. When your signal accesses your local repeater, but it is not sent to the destination repeater, the repeater replies with an status message. PROBLEM POSSIBLE CAUSE - Icom ID-5100A | Full Instruction Manual - Page 97
STAR OPERATION Troubleshooting (Continued) PROBLEM POSSIBLE CAUSE The simplex operation can- • A repeater frequency is programmed. not be made in the DR screen. The digital code squelch • The wrong digital code is set. (CSQL) is impossible. You don't know how to up- - date the repeater - Icom ID-5100A | Full Instruction Manual - Page 98
FM repeaters using the Near Repeater (FM) scan. Search for the nearest repeater (p. 6-21) Searches for the nearest repeater by using your location and the repeater's location. The nearest repeaters in your transceiver's repeater list are displayed as the selectable choices. • When the "FROM" data is - Icom ID-5100A | Full Instruction Manual - Page 99
the DR screen, and the selected repeater is set in "FROM." Repeater call sign IMPORTANT! The repeater list, described in this manual, may differ from your transceiver's preloaded contents. When you select an FM repeater: When an FM repeater is in your transceiver's repeater list, you can select it - Icom ID-5100A | Full Instruction Manual - Page 100
your signal, because the repeater's output power is higher than your transceiver's. For your reference: • Touching [SCAN] for 1 second starts the last used scan. • The DR scan scans the simplex frequencies in the repeater list, in addition to a D-STAR repeaters. Blinks When receiving a signal - Icom ID-5100A | Full Instruction Manual - Page 101
Previous view 6 D-STAR OPERATION "FROM" (Access repeater) setting (Continued) DDUsing the Near Repeater Search function The transceiver searches for the nearest repeater by using your location and the repeater's position. The nearest repeater in your transceiver's repeater list is displayed - Icom ID-5100A | Full Instruction Manual - Page 102
. • TX History (FM): D isplays the TX history of the FM repeaters. yyTouch the repeater to use as your access repeater. (Example: "Hirano") • The transceiver returns to the DR screen, and the selected repeater is set in "FROM." For your reference: When you touch [QUICK] in the step y, you - Icom ID-5100A | Full Instruction Manual - Page 103
a call, the repeater or caller station data is stored in RX data is stored in TX History. You can select the destination from the record. [TO SELECT] screen To make a call through a reflector "Reflector" setting (p. 6-31) Select a reflector you want to call through. To make a call to a specific - Icom ID-5100A | Full Instruction Manual - Page 104
in "TO." rrTouch "Gateway CQ." • Opens the "REPEATER GROUP" screen. ttTouch the repeater group where your destination repeater is listed. (Example: "11: Japan") yyTouch the destination repeater. (Example: "Hamacho") • The transceiver returns to the DR screen, and "Hamacho" is displayed in - Icom ID-5100A | Full Instruction Manual - Page 105
programmed "UR" (destination) call signs. When you select an individual station call sign for the "TO" (Destination) setting using "Your Call Sign," you can make a gateway call. When you call the destination through a gateway, the signal is automatically sent to the last repeater The transceiver - Icom ID-5100A | Full Instruction Manual - Page 106
6 D-STAR OPERATION "TO" (Destination) setting (Continued) DDUsing the RX History When a call is received in the DV mode, the call data is , touch [∫] or [√] one or more times to select another page. • The transceiver returns to the DR screen, and "TOM" is displayed in "TO." The call sign - Icom ID-5100A | Full Instruction Manual - Page 107
the "TX HISTORY" screen. ttTouch the destination name or call sign. (Example: "Hamacho") • The transceiver returns to the DR screen, and "Hamacho" is displayed in "TO." The Sub name is displayed when a repeater is selected. For your reference: If you touch [QUICK] on the TX HISTORY screen, you can - Icom ID-5100A | Full Instruction Manual - Page 108
Previous view 6 D-STAR OPERATION "TO" (Destination) setting (Continued) DDDirectly uuRepeat steps t and y to program a call sign of up to 8 characters, including spaces, and then touch [ENT]. (Example: First, J, then M, then 1, then Z, then L, then K.) • The transceiver returns to - Icom ID-5100A | Full Instruction Manual - Page 109
)." • Opens the "DIRECT INPUT (RPT)" screen. uuRepeat steps t and y to program a call sign of up to 8 characters, including spaces, and then touch [ENT]. (Example: First, J, then P, then 1, then Y, then I, then U, then space, then A.) • The transceiver returns to the DR screen, and "JP1YIU" is - Icom ID-5100A | Full Instruction Manual - Page 110
a version of dplus software. If the dplus software is installed on your access repeater, it provides various functions including gateway and reflector linking capabilities (It is known as the D-STAR reflector system). The D-STAR reflector system enables a number of D-STAR repeaters around the world - Icom ID-5100A | Full Instruction Manual - Page 111
view 6 D-STAR OPERATION Reflector operation (Continued) DDLinking to a reflector If your repeater is not currently B) rrTouch "Reflector." • Opens the "REFLECTOR" screen. ooTouch [SET]. • The transceiver returns to the DR screen. • "Link to Reflector" and "REF010BL" are displayed in " - Icom ID-5100A | Full Instruction Manual - Page 112
STAR OPERATION Reflector operation DDLinking to a reflector (Continued) Using the TX History The TX History stores the up to 5 reflectors that your access repeater Link to Reflector." ttTouch "Use Reflector." • The transceiver returns to the DR screen. • "Use Reflector" and "CQCQCQ" are - Icom ID-5100A | Full Instruction Manual - Page 113
STAR a useful check of how well your signal is getting into the repeater, and you can use it to verify that your repeater is the "REFLECTOR" screen. ttTouch "Unlink Reflector." • The transceiver returns to the DR screen. • "Unlink Reflector" and "U" are Release [PTT] to hear your message. 6-33 - Icom ID-5100A | Full Instruction Manual - Page 114
page. yyTouch "Repeater Information." • The transceiver returns to the DR screen. • "Repeater Information" and "I" are displayed in "TO." uuHold down [PTT] to send the repeater information command. • The LED1 on the microphone lights red. iiRelease [PTT] to hear the repeater ID message. 6-34 - Icom ID-5100A | Full Instruction Manual - Page 115
transceiver. This section describes how to manually update the repeater list using an SD card. You can download the latest repeater list from the Icom website. 1. Downloading the latest repeater list q A ccess the following URL to download the latest data. http://www.icom.co.jp/world/support - Icom ID-5100A | Full Instruction Manual - Page 116
on inserting the SD card into the transceiver. PC Transceiver SD card from the external card reader Icom recommends that you save the current data before loading other data into the transceiver. 5. Updating the repeater list u Touch [MENU]. i T ouch [Repeater list]. (SD Card > Import/Export - Icom ID-5100A | Full Instruction Manual - Page 117
Previous view 6 D-STAR OPERATION Saving settings When "FROM" (Access repeater) and "TO" (Destination) settings are . • "FROM" and "TO" names are automatically programmed as the Memory name. U p to 16 alphanumeric characters can be programmed for the memory name. yyTouch [MR]. • Selects - Icom ID-5100A | Full Instruction Manual - Page 118
, described in this manual, may differ from your transceiver's preloaded contents. • A lthough Japanese repeaters are used in the setting examples, the Japanese repeater node (port) letters are different from other country's. Be sure to add the repeater node letter in the 8th digit of the call - Icom ID-5100A | Full Instruction Manual - Page 119
Previous view 7 D-STAR OPERATION Message operation You can store up to 5 the keyboard type. Selectable characters and symbols A to Z, a to z, 0 to 9 space) Keys used for entry Moves the cursor Deletes Sets Cancels Enters a space Toggles the entry mode Toggles between upper case - Icom ID-5100A | Full Instruction Manual - Page 120
Previous view 7 D-STAR OPERATION Message operation (Continued) 2. Enter the TX message (Continued) yyTouch [] to move the cursor backwards, or touch [] to move the cursor forwards. uuRepeat steps t and y to enter a name of up to 20 characters, including spaces. (Example: First, J, - Icom ID-5100A | Full Instruction Manual - Page 121
Previous view 7 D-STAR OPERATION Message operation (Continued) DDTransmitting a message You can transmit a pre-entered text message by pushing [PTT]. First, select a TX message which also turns ON - Icom ID-5100A | Full Instruction Manual - Page 122
Previous view 7 D-STAR OPERATION Message operation (Continued) DDTX message deleting The programmed TX message can be deleted, as described below. Example: T o delete the programmed TX message "JAPAN >TOM" from message memory number 1. qqTouch [MENU]. wwTouch "TX Message." (My Station > - Icom ID-5100A | Full Instruction Manual - Page 123
D-STAR OPERATION Viewing the received call signs When you receive a DV call, the calling station and the repeater's call signs are stored in the RX HISTORY screen. Up to 50 calls can be stored. When you receive the 51th call, the oldest history will be deleted. Even if the transceiver is - Icom ID-5100A | Full Instruction Manual - Page 124
from. "FREQUENCY" appears instead of these items when the call was not through a repeater (Simplex call), to show the frequency that was used. yyTouch [MENU]. • Closes the Menu screen. You can delete the RX HISTORY data. ➥➥Touch the RX HISTORY or the contents screen for 1 second, or touch [QUICK - Icom ID-5100A | Full Instruction Manual - Page 125
when transceiver is turned OFF. qqWhile two other stations are communicating in the DV mode, touch [RX>CS] for 1 second. • After releasing, beeps sound and the calling station call sign is announced. (RX>CS Speech function) • The calling station or call sign of the repeater used is automatically - Icom ID-5100A | Full Instruction Manual - Page 126
digital call sign/digital code squelch is in use. (Default: OFF) NOTE: The EMR communication function is automatically turned OFF when the transceiver is turned OFF. Example: To transmit from the "Hirano" repeater using ] control level, whichever is higher. yyRelease [PTT] to receive. uuTo cancel - Icom ID-5100A | Full Instruction Manual - Page 127
Previous view 7 D-STAR OPERATION Display type setting You can change the letter size in the DR screen, such as a repeater name, call sign, and so on to see the let- ters better. (Default: Normal) qqTouch [QUICK]. [QUICK] wwTouch "Display Type." • If the specified item - Icom ID-5100A | Full Instruction Manual - Page 128
the item is not displayed, touch [∫] or [√] one or more times to select another page. For your reference: When digital call sign squelch (DSQL) or digital code squelch (CSQL) is selected, the transceiver does not receive FM signals, even if this function is ON. You can silently wait for calls from - Icom ID-5100A | Full Instruction Manual - Page 129
STAR using the internal GPS receiver. While in the Dualwatch mode, automatically replies only when the signal is received in the MAIN band. - When the "GPS Select" item is set to "OFF" or "Manual receiving a call from "JM1ZLK," the transceiver automatically sends a reply call. The " - Icom ID-5100A | Full Instruction Manual - Page 130
7 D-STAR OPERATION Automatic Reply function (Continued) DDRecording an Auto Reply voice announcement The Auto Reply voice announcement can be recorded and saved on an SD card to reply to the call with your voice. NOTE: Be sure to insert an SD card to the [SD] slot of the transceiver - Icom ID-5100A | Full Instruction Manual - Page 131
on the screen of the called station. • Icom transceivers prior to the ID-5100A/E do not show the position after receiving a call. (ID-31A/E, IC-9100, ID-880H/ E880, IC-80AD/E80D, IC-92AD/E92D, IC-2820H/E2820, ID-800H, IC-91AD/E91, IC-V82, IC-U82) • The called station's position window can - Icom ID-5100A | Full Instruction Manual - Page 132
7 D-STAR OPERATION Low-speed data communication In addition to digital voice communication, low-speed data communication can be made. Use the optional data communication cable and a serial data communication software (third-party's). DDConnection Connect the transceiver to your PC using - Icom ID-5100A | Full Instruction Manual - Page 133
addressed to your own call sign. Thus the digital call sign squelch function can be used when communicating with only one station. • Even if the squelch closes by the digital call sign squelch function, you can receive the low-speed data. When the received signal includes a matching call sign - Icom ID-5100A | Full Instruction Manual - Page 134
7 D-STAR OPERATION Digital squelch functions (Continued) DDThe digital code squelch setting qqTouch [DR]. • Opens the DR screen. wwTouch the Function group icon one or more times. • Selects the D-3 menu. eeTouch [DSQL]. rrTouch "CSQLS" or "CSQL". • CSQLS: Turns ON the digital code - Icom ID-5100A | Full Instruction Manual - Page 135
Previous view 7 D-STAR OPERATION Viewing the call signs While in the DV mode the "CALL SIGN" screen. ttTouch []. • Exits the "CALL SIGN" screen. While operating D-STAR in the Memory mode. Destination call sign Access repeater call sign Gateway repeater call sign Your own call sign 7-18 - Icom ID-5100A | Full Instruction Manual - Page 136
the DV mode The transceiver can simultaneously monitor two different frequencies in the DV mode. For example, while operating in the Simplex mode on the MAIN band, you can also monitor a D-STAR repeater on the SUB band. • While receiving or transmitting a DV signal on the MAIN band, DV mode audio - Icom ID-5100A | Full Instruction Manual - Page 137
memory channels and the repeater list. We recommend that you back up the memory data to a SD card or save it to a PC using the CS-5100 cloning software. About the repeater list: The repeater list can be downloaded from the Icom website. http://www.icom.co.jp/world/support/download/firm/ index.html - Icom ID-5100A | Full Instruction Manual - Page 138
STAR OPERATION Entering new information into the Repeater List This section describes how to manually enter new repeater information into the repeater Repeater list Used as an Used as a destina- Used for DV contents access repeater tion repeater simplex TYPE DV Repeater DV Repeater - Icom ID-5100A | Full Instruction Manual - Page 139
in other countries. 1200 MHz: A (B in Japan) 430 MHz: B (A in Japan) 144 MHz: C (no D-STAR repeaters in Japan) Selectable characters and symbols A to Z, a to z, 0 to 9 space) Cross band operation between different nodes at the same repeater site can be made. ☞ Continued on the next page. 7-22 - Icom ID-5100A | Full Instruction Manual - Page 140
group, 01 to 30. 8. Setting "USE(FROM)" to be used as an Access repeater You can use the programmed repeaters as an access repeater when using the DR function. When not using as an access repeater, select "NO," and go to'15.Selecting the position data accuracy level.' In this case, the entered - Icom ID-5100A | Full Instruction Manual - Page 141
not used, or the distance between your position and a repeater is not displayed, select "OFF," and go to '18. Setting the UTC offset.' $3 Touch "POSITION." $4 Touch the position data accuracy level. • None: Select when the repeater has no position data. • Approximate: Select when the programmed - Icom ID-5100A | Full Instruction Manual - Page 142
7 D-STAR OPERATION Editing a repeater list This function edits a repeater's data. This is useful when already-entered data is incorrect, has changed, or some data needs to be added to the list. qqTouch [MENU]. wwTouch "Repeater List." (DV Memory > Repeater List) • The repeater groups - Icom ID-5100A | Full Instruction Manual - Page 143
view 7 D-STAR OPERATION Deleting a repeater list The programmed repeater contents can be deleted from the repeater list. qqTouch [MENU]. wwTouch "Repeater List." (DV Memory > Repeater List) • The repeater groups are displayed. eeTouch the repeater group where the repeater you want to - Icom ID-5100A | Full Instruction Manual - Page 144
7 D-STAR OPERATION Rearranging the display order of the repeater You can move the programmed repeaters to rearrange their display order in the selected repeater group. The programmed repeater cannot be moved out of their assigned repeater group. qqTouch [MENU]. wwTouch "Repeater List - Icom ID-5100A | Full Instruction Manual - Page 145
Previous view 7 D-STAR OPERATION Adding the Repeater information using the RX History This section describes how to add new repeater information to the repeater list using the RX history. qqTouch [MENU]. wwTouch "RX History." eeTouch [∫] or [√] to display the desired repeater you want - Icom ID-5100A | Full Instruction Manual - Page 146
DR scan You can set repeaters as scan skip repeaters. The selected repeaters are then skipped for faster scanning. You can set the skip setting to all repeaters in the selected repeater group, or to individual repeaters. When a repeater is specified as a skip repeater, its "USE (FROM)" setting is - Icom ID-5100A | Full Instruction Manual - Page 147
view 7 D-STAR OPERATION Repeater group name programming qqTouch [MENU]. wwTouch "Repeater List." (DV Memory > Repeater List) • If the item is not displayed, touch [∫] or [√] one or more times to select another page. • The repeater groups are displayed. eeTouch the repeater group where - Icom ID-5100A | Full Instruction Manual - Page 148
Previous view 7 D-STAR OPERATION Repeater detail screen According to content, such as position data, UTC offset, and so on, the distance between your position and the repeater or the repeater time can be displayed on the REPEATER DETAIL screen. The Detail screen can also be entered from - Icom ID-5100A | Full Instruction Manual - Page 149
7 D-STAR OPERATION Entering Your (destination) call sign A Your (destination) call sign can be manually entered. Touch [] to move the cursor backwards, or touch [] to move the cursor forwards. iiRepeat steps u and i to enter a name of up to 16 characters, including spaces. (Example - Icom ID-5100A | Full Instruction Manual - Page 150
the Menu screen. "Station2 JG3LUK" is entered into the Your Call Sign memory. To edit the entered data: To reprogram a Your (destination) call sign's data, touch "Edit" in step q. This is useful when already-entered data is incorrect, has changed or some data needs to be added to the list. 7-33 - Icom ID-5100A | Full Instruction Manual - Page 151
Previous view 7 D-STAR OPERATION Deleting Your (destination) call sign The Your (destination) call to delete for 1 second. rrTouch "Delete." ttTouch "YES." • The programmed call sign contents are deleted from the Your call sign list, and the display returns to the YOUR CALL SIGN screen. - Icom ID-5100A | Full Instruction Manual - Page 152
Previous view 7 D-STAR OPERATION Rearranging the display order of Your (destination) call signs You can move Your call signs to rearrange their display order. It is easy - Icom ID-5100A | Full Instruction Manual - Page 153
Previous view 7 D-STAR OPERATION Your setting is correct? If you make a local area call with a gateway setting still selected in "TO," the destination repeater will be busy while you transmit. So the stations that use that repeater as their Access repeater cannot access it, as shown - Icom ID-5100A | Full Instruction Manual - Page 154
screen. To reset the programmed repeater list to the default, write the ICF file to the transceiver using the CS-5100*1, or copy the ICF file to the SD card*2, and then write to the transceiver. *1 See the CS-5100 instruction manual when using the CS-5100. *2 See Section 9 when using the SD card - Icom ID-5100A | Full Instruction Manual - Page 155
23 DDWeather station transmission 8-25 DDConfirming the weather data input 8-25 DDApplication setting 8-25 DDAbout the weather data content 8-25 DDDisplaying your position using a mapping program 8-26 Transmitting NMEA data 8-27 DDSetting the GPS data sentence 8-27 DDEntering the GPS message - Icom ID-5100A | Full Instruction Manual - Page 156
view 8 GPS OPERATION GPS operation The transceiver has a built-in GPS receiver. You can check your current position, and transmit GPS data in the DV mode. DDGPS receive setting location. • When "GPS Select" item is set to "Manual," the icon does not appear. (GPS > GPS Set > GPS Select) 8-2 - Icom ID-5100A | Full Instruction Manual - Page 157
is displayed in the RX position window. After a few seconds, the pop-up window disappears. RX position indicator When the received signal contains position data, the RX position indicator is displayed on the right side of the message. If you touch the RX position indicator, the RX position window - Icom ID-5100A | Full Instruction Manual - Page 158
using received data. DDDisplaying Position Data GPS Select" is set to "Manual." (p. 12-20) (GPS , antenna gain, antenna direction band in the position screen Dualwatch mode Shows the time the caller acquired the position data assigned to the memory channel, date and time are displayed instead - Icom ID-5100A | Full Instruction Manual - Page 159
a weather information received from the weather device. • NMEA: A station transmitting position data (NMEA0183) received from the internal or an external GPS receiver. For users who have a D-STAR transceiver model prior to the ID-5100A/E: The GPS TX mode, "GPS (DV-G)" and "GPS-A (DVA)," are now - Icom ID-5100A | Full Instruction Manual - Page 160
items differ. D-PRS Position Object Item NMEA Mobile Base Data extension: OFF Data extension: Course/Speed Data extension: Power/Height/Gain/Directivity Data extension: OFF Data extension: Course/Speed Data extension: Power/Height/Gain/Directivity Weather Compass Latitude Longitude Grid - Icom ID-5100A | Full Instruction Manual - Page 161
the caller's SSID Displays the time that the caller acquired the position data. Displays the caller's call sign (with SSID) Compass Latitude Longitude GL the height of caller's antenna Displays the gain of caller's antenna Displays the direction the caller's antenna was pointing Displays the caller - Icom ID-5100A | Full Instruction Manual - Page 162
Displays the gain of Object station's antenna Displays the direction that the Object station's antenna was pointing Displays the Object station's D-PRS symbol Displays the caller's SSID Displays the time that the caller sent the Object station's data. Displays the caller's call sign (with SSID - Icom ID-5100A | Full Instruction Manual - Page 163
the caller station's area Displays the caller station's D-PRS symbol Displays the caller's SSID Displays the time that the caller acquired the weather data. Displays the caller's call sign (with SSID) Compass* Latitude Longitude GL ALT DST COURSE SPEED GPS Time Stamp Call sign Displays the caller - Icom ID-5100A | Full Instruction Manual - Page 164
station's position information is displayed. • MAIN: The position information of the station received on the MAIN band is displayed. • SUB: The position information of the station received on the SUB band is displayed. DDChanging the GPS memory or alarm You can change the GPS memory or GPS alarm - Icom ID-5100A | Full Instruction Manual - Page 165
a 6 character code, calculated by the longitude and the latitude. The locator is simply calculated by dividing the earth surface into squares. It is used to find the location of a radio station. DDChanging the Compass Direction You can change the compass direction between Heading Up, North Up and - Icom ID-5100A | Full Instruction Manual - Page 166
of the station you received from, select "RX." rrTouch [QUICK]. yyTouch "." • Opens "Add write?" window. • The latitude and longitude data on the "GPS POSITION" screen is automatically entered. • You can select the destination group to be stored. Select a destination group to save - Icom ID-5100A | Full Instruction Manual - Page 167
Previous view 8 GPS OPERATION Checking GPS information (Sky view screen) This screen is used to view GPS satellite information when the GPS indicator does not stop blinking for a long time. GPS Information displays the quantity, signal power and position - Icom ID-5100A | Full Instruction Manual - Page 168
D-STAR transceiver model prior to the ID-5100A/E: The GPS TX mode, "GPS (DV-G)" and "GPS-A (DVA)," are now called as "NMEA" and "D-PRS." • GPS (DV-G) NMEA • GPS-A (DV-A) D-PRS For users who have one of the following models: (ID-800H, IC-91AD/E91, IC-U82, IC-V82, IC-7100, ID-51A/E, ID-31A/E, IC - Icom ID-5100A | Full Instruction Manual - Page 169
Set > Manual Position) • Please note that if "GPS Auto TX" is set to any other setting than "OFF," the data is transmitted according to the set time. (p. 8-41) (GPS > GPS Auto TX) • The image of D-PRS Voice, Messages and D-PRS positions D-STAR repeater Information from an APRS - Icom ID-5100A | Full Instruction Manual - Page 170
, the setting items differ. D-PRS Position Object Item Mobile Base Data extension: OFF Data extension: Course/Speed Data extension: Power/Height/Gain/Directivity Data extension: OFF Data extension: Course/Speed Data extension: Power/Height/Gain/Directivity Weather Unproto Address Comment - Icom ID-5100A | Full Instruction Manual - Page 171
used, and editing is not recommended. rrTouch "Unproto Address." • The default setting is "API510,DSTAR the position data. iiTouch " converted to "-." If no text is programmed after the space, the space will includes a space, any text or digit after the space will be deleted. used in D-PRS (APRS - Icom ID-5100A | Full Instruction Manual - Page 172
comment on the products that cannot display the altitude. (IC-9100, IC-80AD, IC-E80D, ID-880H, ID-E880, IC-92AD, IC-E92D, ICU82, IC-V82) 9. Setting the Data Extension Set the data extension of your station's information. @5 Touch "Data Extension." @6 Touch the desired option to transmit. • OFF - Icom ID-5100A | Full Instruction Manual - Page 173
Height/Gain/Directivity." Select the height of the base station's antenna, to transmit in addition to the position data. @9 Touch "Height." #0 T ouch the desired option should be used, and editing is not recommended. rrTouch "Unproto Address." • The default setting is "API510,DSTAR*." ttTouch []. - Icom ID-5100A | Full Instruction Manual - Page 174
station. The number of characters you can enter differs, depending on the data extension and altitude settings. (p. 8-18) Data Extension Altitude Characters entered (Max.) OFF No data 43 (Default) OFF Set 35 Course/Speed No data 36 Course/Speed Set 28 Power/Height/Gain/Directivity No - Icom ID-5100A | Full Instruction Manual - Page 175
Opens the altitude edit screen. #6 Enter the altitude. • After entering a digit, touch "+/-" to toggle between plus and minus. • Touch [CE] to Item station if the station is a repeater, node, access point, and so on and an antenna is installed. $7 Touch "Data Extension." $8 T ouch the desired - Icom ID-5100A | Full Instruction Manual - Page 176
antenna height This item appears when "9. Setting Data Extension" is set to "Power/Height/Gain/Directivity." Select the height of the Object or Item's antenna if the station is a repeater, node, access point, and so on and an antenna text is programmed after the or digit after the used in D-PRS (APRS - Icom ID-5100A | Full Instruction Manual - Page 177
used, and editing is not recommended. rrTouch "Unproto Address." • The default setting is "API510,DSTAR APRS® (Automatic Packet Reporting System) based SSID is added after the D-PRS data to "-." If no text is programmed after the space, the space a space, any text or digit after the space will be - Icom ID-5100A | Full Instruction Manual - Page 178
the previous screen. @0 Touch [√] to select the next page. 7. Setting the Time Stamp Set the time stamp function to transmit the received time data in UTC (Universal Time Coordinated) time. @1 Touch "Time Stamp." @2 Touch the desired time stamp. • OFF : Does not transmit the time information. • DHM - Icom ID-5100A | Full Instruction Manual - Page 179
the weather information screen, the weather data does not input to the [DATA] terminal. In this case, check the input data settings. DDApplication setting Configure the communication software as follows. • Port: The COM port number that is used by the ID-5100A/E.*1 • Baud rate: 4800/9600 bps - Icom ID-5100A | Full Instruction Manual - Page 180
D-PRS data (Continued) DDDisplaying your position using a mapping program If ID-5100 OP.SATOH qw e ru i o !0 o !2 !4 DObject (e.g.) JA3YUA-A>API510,DSTAR*:;HAM FESTA*012345z3437.38N\13534.29Eh/2014.2.28 am10-pm4 qw e r t yu i o !0 o !4 DItem (e.g.) JA3YUA-A>API510,DSTAR*:)REPEATER - Icom ID-5100A | Full Instruction Manual - Page 181
digital transceivers (IC-2820H, IC-E2820, ID-800H, IC-91AD, IC-E91, IC-V82, IC-U82, IC-2200H). The GSV sentence is incompatible with them. • If "GPS Select" is set to "Manual," the transceiver automatically sets the NMEA sentence and transmits it according to the position data in "Manual - Icom ID-5100A | Full Instruction Manual - Page 182
message of up to 20 characters to be transmitted with the position data. Example: Adding "HELLO HOW ARE YOU?" qqTouch [MENU]. wwTouch [] to move the cursor backwards, or touch [] to move the cursor forwards. yyRepeat steps r and t to enter a GPS message of up to 20 characters, including spaces - Icom ID-5100A | Full Instruction Manual - Page 183
Previous view 8 GPS OPERATION Adding or editing GPS memory DDGPS memory You can add GPS data to GPS Memory. You can add your own position, other station's positions or any positions that are manually programmed. The GPS Memory is capable of storing a total of 200 channels, and conveniently stored - Icom ID-5100A | Full Instruction Manual - Page 184
edit mode. 3. Entering the GPS Memory date !1 T ouch "DATE." • Enters the date edit mode. uuTouch the keypad. the cursor backwards, or touch [] to move the cursor forwards. ooRepeat steps u and i to enter a GPS memory name of up to 16 Icom 01" is entered. 8-30 ☞☞Continued on the next page - Icom ID-5100A | Full Instruction Manual - Page 185
move the cursor forwards. • Touch "N/S" to toggle between north and south. @0 Repeat steps !8 and !9 to enter the latitude. @1 Touch [ENT]. @9 Enter You can enter from -10.000 to +10.000 meters. • After entering a digit, touch "+/-" to toggle between plus and minus. #0 Touch [ENT]. @2 Touch [√] - Icom ID-5100A | Full Instruction Manual - Page 186
was edited, touch "." #4 Touch [YES]. • Writes the entered content into the GPS memory. • The data is added to the GPS memory, and then the data screen is displayed. Completed Example: When "Icom 01" is added into "(No group)." To view the entered content: To view the entered - Icom ID-5100A | Full Instruction Manual - Page 187
characters and symbols A to Z, a to z, 0 to 9 space) yyTouch [] to move the cursor backwards, or touch [] to move the cursor forwards. uuRepeat steps u and i to enter a GPS group name of up to 16 characters, including spaces. iiAfter entering, touch [ENT]. Example: Home area is entered 8-33 - Icom ID-5100A | Full Instruction Manual - Page 188
Adding or editing GPS memory (Continued) DDClearing GPS data GPS memories can be cleared (erased). Please note that erased GPS memories cannot be restored. There are two ways to clear the memories: • Erasing all GPS memory in a group. • Erasing a specific memory channel. Example: Erasing all in the - Icom ID-5100A | Full Instruction Manual - Page 189
Previous view 8 GPS OPERATION Adding or editing GPS memory (Continued) DDRearranging the display order of the GPS data You can move programmed GPS memories to rearrange their display order in the selected GPS memory group. In order to move the GPS memory out of their assigned memory - Icom ID-5100A | Full Instruction Manual - Page 190
." (GPS > GPS Alarm) • If the item is not displayed, touch [∫] or [√] one or more times to select another page. Alarm area 2 (Setting specific station) When a specified memory is selected: Extended range (approx. 1 km; 1094 Y) Your position Limited range (approx. 500 m; 547 Y) Beeps one times - Icom ID-5100A | Full Instruction Manual - Page 191
Previous view 8 GPS OPERATION Adding or editing GPS memory DDSetting the GPS alarm (Continued) Example: Set the alarm setting to RX (RX/Memory). qqTouch [MENU]. wwTouch "GPS Alarm." (GPS > GPS Alarm) • If the item is not displayed, touch [∫] or [√] one or more times to select another page. ee - Icom ID-5100A | Full Instruction Manual - Page 192
Date. If you use this GPS Logger while driving, you can check your driving history on a mapping software. DDGPS Logger operating outline To use as a log. When the GPS Logger function is ON, the transceiver stores the position data from GPS receiver into SD card in a specified time interval. The - Icom ID-5100A | Full Instruction Manual - Page 193
data, copy the log file to your PC. Windows 7 is used for these instructions. qqTurn OFF the power. wwPush in the SD card until a click sounds, and then carefully pull it out. • DO NOT touch the terminals. • To removing the card while the transceiver Displays the 'ID-5100' folder. Double- - Icom ID-5100A | Full Instruction Manual - Page 194
logging Regarding the GPS logging data of the ID-5100A/E, each sentence corresponds to data 2=DGPS (SPS), 6=Estimated (Dead Reckoning) mode started with "*" (hex code) y Number of satellites in use y Horizontal Dilution of Precision (1.0) 0.0-50.0 M=Manual, forced to operate in 2D or 3D mode - Icom ID-5100A | Full Instruction Manual - Page 195
or "Manual." (p. 12-20) Otherwise, you cannot use this Use GPS automatic transmission in only the simplex mode. • GPS automatic transmission through a repeater may interfere with other communications. When a GPS message is programmed, the transceiver transmits it along with the position data - Icom ID-5100A | Full Instruction Manual - Page 196
Previous view Section 9 USING AN SD CARD About the SD card 9-2 Saving data onto the SD card 9-3 Inserting the SD card 9-4 DDInserting the SD card 9-4 DDFormatting the SD card 9-4 Removing the SD card 9-5 DDRemoving the SD card 9-5 DDRemoving the SD card while the transceiver's power is ON - Icom ID-5100A | Full Instruction Manual - Page 197
of up to 32 GB, can be used with the ID-5100A/E. Icom has checked the compatibility with the following SD using the SD card, read the instructions of the SD card thoroughly. • If you do any of the following, the SD card data may be corrupted or deleted. - You remove the SD card from the transceiver - Icom ID-5100A | Full Instruction Manual - Page 198
Previous view 9 USING AN SD CARD Saving data onto the SD card The following data can be stored onto the card: • Data settings of the transceiver Memory channel contents, repeater lists, Your (UR) memory and GPS memory that are stored in the transceiver. • Communication contents The transmitted and - Icom ID-5100A | Full Instruction Manual - Page 199
by doing the following steps. • Formatting a card erases all its data. Before formatting any used card, back up its data onto your PC. qqTurn OFF the transceiver, and then insert the card into the slot. wwTurn ON the transceiver. • " " appears when the SD card is inserted. Displayed Front panel - Icom ID-5100A | Full Instruction Manual - Page 200
Previous view 9 USING AN SD CARD Removing the SD card DDRemoving the SD card qqTurn OFF the power. wwPush in the SD card until a click sounds, and then carefully pull it out. Main unit Push Pull out DDRemoving the SD card while the transceiver's power is ON qqTouch [MENU]. wwTouch - Icom ID-5100A | Full Instruction Manual - Page 201
on an SD card allows you to easily restore the transceiver to its previous settings, even if an All reset is performed. ✓✓ For your information Data settings are saved in the "icf" file format that is used in the CS-5100 cloning software. The saved data on an SD card can be copied to a PC and - Icom ID-5100A | Full Instruction Manual - Page 202
Previous view 9 USING AN SD CARD Saving with a different file name qqTouch [MENU]. move the cursor backwards, or touch [] to move the cursor forwards. uuRepeat steps t and y to enter a name of up to 10 characters. (Example: My data) iiTouch [ENT] to save the name. • The confirmation window "Save - Icom ID-5100A | Full Instruction Manual - Page 203
convenient when copying the saved data, such as memory channels, or repeater lists, to another ID-5100, and then operating with the same data. To update the repeater list, click here! Saving the current data is recommended before loading other data into the transceiver. (Example: Loading all the - Icom ID-5100A | Full Instruction Manual - Page 204
, connect an external memory card reader to use the SD card. DDAbout the SD card's folder contents The folder in the SD card contains the following: qqID-5100 folder Contains the folders created in the ID-5100. wwCsv folder Contains the GPS Memory, Repeater List and Your Call Sign Memory folders - Icom ID-5100A | Full Instruction Manual - Page 205
up the data stored on the SD card onto a PC (Continued) DDMaking a backup file on your PC Windows 7 is used for these instructions. qq Displays the 'ID-5100' folder. ttOpen the desired folder to copy to, then right-click, and then click "Paste." • Copies the SD card data onto your hard disk - Icom ID-5100A | Full Instruction Manual - Page 206
file from the SD card. You can import or export the following data: • Your Call Sign Memory • Repeater List • GPS Memory DDImporting Before importing, make a backup file of all the transceiver's data to the SD card in case of data loss. Example: Importing the Your Call sign memory. qqTouch [MENU - Icom ID-5100A | Full Instruction Manual - Page 207
Previous view 9 USING AN SD CARD Importing or Exporting a CSV format file (Continued) DDExporting You can export Your Call Sign Memory, Repeater List and GPS Memory. Example: Exporting the Your Call sign memory. qqTouch [MENU]. wwTouch "Your Call Sign." (SD Card > Import/Export > Export > Your - Icom ID-5100A | Full Instruction Manual - Page 208
Previous view Section 10 VOICE MEMORY Recording a QSO audio 10-2 DDTo starting to record 10-2 DDTo stop recording 10-2 Playing back the recorded audio 10-3 DDPlaying back the recording 10-3 Changing the QSO recorder settings 10-4 Deleting the audio folder/file 10-5 DDDelete an Audio Folder - Icom ID-5100A | Full Instruction Manual - Page 209
QSO audio Recording a QSO audio using the MAIN band. NOTE: Be sure to insert an SD card into the transceiver before recording the audio. DDTo starting until you manually stop recording, or the card becomes full. • If the recording file's content reaches 2GB, the transceiver automatically creates - Icom ID-5100A | Full Instruction Manual - Page 210
Insert the SD card, which contains the recorded audio file, into the transceiver's slot. DDPlaying back the recording qqTouch [MENU]. • Opens the Menu file and the total number of files in the folder. Recorded date Shows the recorded date and time. eeTouch "QSO Recorder." rrTouch "Play Files - Icom ID-5100A | Full Instruction Manual - Page 211
Previous view 10 VOICE MEMORY Changing the QSO recorder settings You can change the recording setting on the Menu screen. See "Voice Memo" item in the Menu screen (p. 12-17) for the setting details. • R ecords only the received audio. ("REC Mode") (Voice Memo > QSO Recorder > Recorder Set) • - Icom ID-5100A | Full Instruction Manual - Page 212
Previous view 10 VOICE MEMORY Deleting the audio folder/file A deleted audio file can NOT be recovered. DDDelete an Audio Folder All audio files in the folder are deleted. qqTouch [MENU]. • Opens the Menu screen. wwTouch "Voice Memo." uuTouch [Yes]. • A beep sounds, and then the folder is deleted - Icom ID-5100A | Full Instruction Manual - Page 213
files in the folder. ttTouch the folder that contains the audio file to delete. yyTouch and hold the file to delete, for 1 second. Date Time Operating mode Operating frequency Time uuTouch [Delete]. 10-6 - Icom ID-5100A | Full Instruction Manual - Page 214
: View the folder information: Touch [QUICK] in Step w, and then touch "Folder Information" to view the folder information. Folder Total files name (total size) Created date My station location Caller and received repeater UR station location File data 10-7 - Icom ID-5100A | Full Instruction Manual - Page 215
Previous view 10 VOICE MEMORY Viewing the SD card memory capacity You can verify the SD card memory capacity and available recording time. qqTouch [MENU]. wwTouch the "SD Card Info." (SD Card > SD Card Info) • R emaining capacity and available recording time. eeTouch [MENU]. • Cancels the Menu - Icom ID-5100A | Full Instruction Manual - Page 216
Operation data is Transceiver SD card Card reader wwClick "Open folder to view files" option to access the card. • Displays the 'ID-5100 ID-5100' folder. Double click Double click yyDouble click the file to play back. (Example: "20140206_145140.wav") Double click • See the instruction manual - Icom ID-5100A | Full Instruction Manual - Page 217
view Section 11 REPEATER AND DUPLEX OPERATIONS FM Repeater operation 11-2 DDChecking the repeater input signal 11-3 DD1750 Hz tone burst 11-3 Duplex operation 11-4 DDSetting the frequency offset 11-4 DDSetting the duplex direction 11-4 DDDuplex operation 11-4 Off band indication 11-5 Auto - Icom ID-5100A | Full Instruction Manual - Page 218
repeater can be accessed using the duplex function by setting the transceiver's offset to the same value as the repeater's offset. See Sections 6 and 7 for details on accessing a DSTAR repeater. 434.540 MHz Repeater the operating band. q Touch the MHz digits. • Opens the operating band setting - Icom ID-5100A | Full Instruction Manual - Page 219
transceiver transmit frequency (repeater input frequency). • When the other station's signal can be directly received, move to a non-repeater frequency and use once to access the repeater with a short tone burst. • "1750Hz TONE" briefly appears. • This operation is only for the ID-5100E. • You can - Icom ID-5100A | Full Instruction Manual - Page 220
selected tuning step in the VFO mode is used when setting the frequency offset. • If be out of the band, "OFF BAND" appears on the transceiver transmit frequency appears on the display. wwTouch [MONI] again to turn OFF monitoring, and then operate in the normal way. NOTE: When the Auto repeater - Icom ID-5100A | Full Instruction Manual - Page 221
Previous view 11 REPEATER AND DUPLEX OPERATIONS Off band indication If the transmit frequency is out of the amateur band, the off band indication, "OFF BAND," appears on the display when [PTT] is pushed. Check the frequency offset (p. 11-4) or duplex direction (p. 11-4) in this case. Appears 11-5 - Icom ID-5100A | Full Instruction Manual - Page 222
repeater output frequency range, the Auto Repeater function automatically sets the repeater settings (duplex ON/OFF, duplex direction, tone encoder ON/OFF). The Auto repeater function uses the preset repeater Auto repeater function has priority over the manual duplex setting. If the transmit frequency - Icom ID-5100A | Full Instruction Manual - Page 223
items 12-49 Function items 12-52 Display items 12-57 Sounds items 12-61 Time Set items 12-62 SD Card items 12-63 Bluetooth Set items 12-64 Others items 12-67 12-1 - Icom ID-5100A | Full Instruction Manual - Page 224
Previous view 12 MENU SCREEN Menu item selection The Menu screen is used to program infrequently changed values or function settings. In addition to this page, see pages 12-3 through 1211 for details of each item's options and their default - Icom ID-5100A | Full Instruction Manual - Page 225
below are for the USA version. The default settings may differ, depending on your transceiver version. DUP/TONE... Offset Freq Repeater Tone TSQL Freq Tone Burst DTCS Code DTCS Polarity Digital Code Settings to access repeaters. 0.000~0.600.00*1~59.995 MHz 67.0~88.5~254.1 Hz 67.0~88.5~254.1 Hz - Icom ID-5100A | Full Instruction Manual - Page 226
Gain Set the GPS options. OFF, Internal GPS or Manual OFF or ON API510,DSTAR* Selects the position data source that the transceiver uses for its position data. Manually enter your current position. Selects to output the GPS information to the [DATA] jack Turns OFF the GPS TX function. Enters an - Icom ID-5100A | Full Instruction Manual - Page 227
on your transceiver version. Directivity SSID Time Stamp Item Item Name Data Type Symbol Comment Position Data Extension °S, Selects the antenna directivity information of the ob- 225°SW, 270°W, 315°NW, 360°N ject station to transmit. - - -, (-0), -1~-15 or -A~-Z Selects the APRS® call sign - Icom ID-5100A | Full Instruction Manual - Page 228
down. OFF or ON Turns the digital repeater setting function ON or OFF. This function is usable in any DV mode except using the DR function. OFF or ON Turns the DV mode automatic detect function ON or OFF. ALL or Latest Only The transceiver can record the data of up to 50 indi- vidual - Icom ID-5100A | Full Instruction Manual - Page 229
/dd/yyyy or dd/mm/yyyy Selects the separator and the decimal character for the CSV format. Selects the date format. Function Squelch/ATT Select Squelch Delay Fan Control Dial Speed-UP Auto Repeater*2 Remote MIC Key During RX/Standby During TX Up/Down MIC Key During RX/Standby During TX One - Icom ID-5100A | Full Instruction Manual - Page 230
version. Active Band MIC Gain Touch Operation (Sub) Keyboard Type Data Speed Single or All 1~2*~4 Main Select or Function Select Ten-key, Full keyboard 4800bps or 9600bps CI-V CI-V Address 01h~8Ch~DFh CI-V Baud Rate CI-V Transceive CI-V Bluetooth➝REMOTE transceive Address 4800, 9600 - Icom ID-5100A | Full Instruction Manual - Page 231
to automatically correct the time using a GPS signal. Enters the time difference between UTC and the local time. or Turns the Auto power OFF function ON or OFF. Sets the SD card options. ALL, Except My Station, Repeater List Only Loads the settings file to the transceiver. Saves the settings as - Icom ID-5100A | Full Instruction Manual - Page 232
transceiver version. Import/Export Import Export CSV Format Separator/Decimal Date SD Card Info Format Unmount Bluetooth Bluetooth Auto Connect Pairing/Connect Device Search Search Headset Search Data tal prolonged transmission. Sets to use the optional Icom Bluetooth® headset (VS-3). OFF or - Icom ID-5100A | Full Instruction Manual - Page 233
or ON Shows the voltage of the external DC power source. Shows the transceiver's firmware version number. Reads or writes the CS-5100 data from or to the PC, and/or to receive data from a Master transceiver. Selects the Repeater mode. Selects the hangup time to cancel the transmission. Adjusts the - Icom ID-5100A | Full Instruction Manual - Page 234
default value may differ, depending on the frequency band (selected as the Main band before entering the Menu screen) and the transceiver version. Repeater Tone (Default: 88.5) DUP/TONE... > Repeater Tone Select a CTCSS tone frequency for repeater access and other functions. 50 tone frequencies - Icom ID-5100A | Full Instruction Manual - Page 235
and edit your memory data. Up to 1000 Memory channels can be stored. Also, 26 memory banks, A to Z, can be used to store groups of data. The Call channel can be assigned to 2 different channels (C0 and C1) in the 144 MHz and 430 MHz bands. The default setting is differ, depending on the transceiver - Icom ID-5100A | Full Instruction Manual - Page 236
timer activates for the VFO scan, Memory scan and DR scan. Program Skip (Default: ON) Scan > Program Skip Turn the Program Skip Scan function ON or OFF for a VFO mode scan. This function enables the transceiver to skip the unwanted frequencies or channels that inconveniently stop scanning. Set - Icom ID-5100A | Full Instruction Manual - Page 237
screen shows the frequency range. (The default scan edge frequency may differ, depending on the transceiver version.) • You can add a link setting with touching [QUICK] when two or more pairs of Program Scan Edge channels are programmed. NOTE: The "Add" item will not be displayed when only one - Icom ID-5100A | Full Instruction Manual - Page 238
Previous view 12 MENU SCREEN Scan items (Continued) Program scan link name programming qqTouch a Program Link number between 0 and 9 for 1 second to cursor backwards, or touch [] to move the cursor forwards. ttRepeat steps e and r to enter a name of up to 16 characters. (Example: Japan) 12-16 - Icom ID-5100A | Full Instruction Manual - Page 239
started, the recording will con- tinue, even if the transceiver is rebooted. To stop the recording, touch " - Icom ID-5100A | Full Instruction Manual - Page 240
the PTT Automatic Recording function ON or OFF. The transmission from the Bluetooth® VOX function and CI-V command also starts recording. • OFF: received for 10 seconds after releasing [PTT]. - When transceiver receives a signal in 10 seconds after releasing [PTT], the recording automatically - Icom ID-5100A | Full Instruction Manual - Page 241
is disabled. Be sure to insert an SD card into the card slot. Repeat Time (Default: 5sec) Voice TX > TX Set > Repeat Time Set the repeat time period to between 1 and 15 seconds (in 1 second steps). The transceiver repeatedly transmits the recorded voice audio for this set time period. NOTE: The - Icom ID-5100A | Full Instruction Manual - Page 242
repeater or antenna information that needs no time information. • Weather: T ransmits weather information received from a weather device. For users who have one of the following models: (ID-800H, IC-91AD/E91, IC-U82, IC-V82, IC-7100, ID51A/E, ID-31A/E, IC-9100, IC-80AD/E80D, ID-880H/E880, IC - Icom ID-5100A | Full Instruction Manual - Page 243
Previous view 12 MENU SCREEN GPS items (Continued) Symbol list 12-21 - Icom ID-5100A | Full Instruction Manual - Page 244
will be auto- matically changed to this set letter ID. Example (SSID [-Z]): "JA3YUA" ➡ "JA3YUA-Z" "JA3YUA A" ➡ "JA3YUA-Z" About SSID To assist in identifying a station's type, designated call sign SSIDs are used in D-PRS (APRS®), according to the common guideline. The guideline may be - Icom ID-5100A | Full Instruction Manual - Page 245
the programmed Power, Height, Gain, and Directivity data in addition to the position data when your position is manually set. When transmitting with this setting, your station is regarded as a base station. Icom transceivers (IC-7100, ID-51A/E, ID-31A/E, IC-9100, IC-80AD/E80D, ID-880H - Icom ID-5100A | Full Instruction Manual - Page 246
transportation or location. The stored symbol is transmitted in addition to the position data while in the D-PRS mode. Editing a symbol qqIn the "Symbol" [-] to select the first digit. • Usable characters: /, \, 0 to 9, A to Z rrTouch [+] or [-] to select the second digit. • Usable characters: - Icom ID-5100A | Full Instruction Manual - Page 247
set it as the object's position. (p. 8-21) Manually enter the position data: qqIn the Quick Menu window, touch "Edit." • digit, touch "+/-" to toggle between plus and minus. !0 Touch [ENT]. !1 Touch []. • Opens the "Write?" window. !2 Touch [YES]. • Programs the entered position data. Data - Icom ID-5100A | Full Instruction Manual - Page 248
height of the object station's antenna, to transmit in addition to the position data. Select between 10, 20, ID. Example (SSID [-Z]): "JA3YUA" ➡ "JA3YUA-Z" "JA3YUA A" ➡ "JA3YUA-Z" About SSID To assist in identifying a station's type, designated call sign SSIDs are used in D-PRS (APRS - Icom ID-5100A | Full Instruction Manual - Page 249
transportation or location. The stored symbol is transmitted in addition to the position data while in the D-PRS mode. Editing a symbol qqIn the "Symbol" [-] to select the first digit. • Usable characters: /, \, 0 to 9, A to Z rrTouch [+] or [-] to select the second digit. • Usable characters: - Icom ID-5100A | Full Instruction Manual - Page 250
set it as the item's position. (p. 8-21) Manually enter the position data: qqIn the Quick Menu window, touch "Edit." • digit, touch "+/-" to toggle between plus and minus. !0 Touch [ENT]. !1 Touch []. • Opens the "Write?" window. !2 Touch [YES]. • Programs the entered position data. Data - Icom ID-5100A | Full Instruction Manual - Page 251
height of the item station's antenna, to transmit in addition to the position data. Select between 10, 20, 40 ID. Example (SSID [-Z]): "JA3YUA" ➡ "JA3YUA-Z" "JA3YUA A" ➡ "JA3YUA-Z" About SSID To assist in identifying a station's type, designated call sign SSIDs are used in D-PRS (APRS - Icom ID-5100A | Full Instruction Manual - Page 252
data no text is programmed after the space, includes a space, any text or digit after the space will be deleted ID. Example (SSID [-Z]): "JA3YUA" ➡ "JA3YUA-Z" "JA3YUA A" ➡ "JA3YUA-Z" About SSID To assist in identifying a station's type, designated call sign SSIDs are used in D-PRS (APRS - Icom ID-5100A | Full Instruction Manual - Page 253
sentences will not be transmitted when your position has been manually set. NOTE: Set the GSV sentence to OFF when sending the GPS message to conventional digital transceivers (IC-2820H, IC-E2820, ID-800H, IC-91AD, IC-E91, IC-V82, IC-U82, IC-2200H). The GSV sentence is incompatible with them. Those - Icom ID-5100A | Full Instruction Manual - Page 254
to send a message, be sure to delete the message programmed in the Quick Menu window. GPS Information GPS > When the "GPS Select" item is set to "Manual," the screen shows only latitude, longitude, altitude, is displayed when no position data is received on your transceiver. 1. When the caller's - Icom ID-5100A | Full Instruction Manual - Page 255
DIRECT Symbol Displays the direction that the Object/Item station's antenna was pointing Displays the Object/Item station's D-PRS symbol SSID Displays the caller's SSID GPS Time Stamp Displays the time that Object station's data. the caller sent the Call sign Displays the caller's call - Icom ID-5100A | Full Instruction Manual - Page 256
GPS > GPS Memory The transceiver has 200 GPS memory channels to store the received position data, or often-used position data, along with an alphanumeric channel channel name (Up to 16 alphanumeric characters) DATE Stored date TIME Stored time LATITUDE Stored location (latitude) LONGITUDE - Icom ID-5100A | Full Instruction Manual - Page 257
and the GPS alarm icon blinks. • Limited : The transceiver sounds 3 beeps and the GPS alarm icon blinks when the target enters the 500 meter range. • blinks when the target enters the 1 kilometer range. • Both : The transceiver sounds a beep and the GPS alarm icon blinks when the target enters the - Icom ID-5100A | Full Instruction Manual - Page 258
ON or OFF. This function logs the position, altitude, course, speed and number of satellites being used. • OFF: Turns OFF the function. • ON: The transceiver automatically logs GPS data. Once this function is turned ON, the GPS data will be continuously logged until turning it OFF, even if the - Icom ID-5100A | Full Instruction Manual - Page 259
is listed). rrTouch "Inage." To manually enter the call sign, touch "UR" for 1 second in step q. About the YOUR SELECT screen CQCQCQ To select "CQCQCQ" to make a noncall sign specific call. Gateway CQ† To select "Gateway CQ" to make a call using the repeater list. Your Call Sign To select - Icom ID-5100A | Full Instruction Manual - Page 260
and the internet, this item displays the gateway repeater call sign of your local area repeater. Displays the call sign of the repeater you received the call from. Displays any message included in the received call, if programmed. Displays the date and time the call was received. 1. When the - Icom ID-5100A | Full Instruction Manual - Page 261
Displays the gain of Object/Item station's antenna DIRECT Displays the direction that the Object/ Item station's antenna was pointing GPS Time Stamp Displays the time that the caller sent the Object station's data. Call sign Displays the caller's call sign (with SSID) Symbol Status Displays - Icom ID-5100A | Full Instruction Manual - Page 262
the humidity of the caller station's area Symbol Displays the caller's D-PRS symbol GPS Time Stamp Displays the time that the caller acquired the position data. GPS MESSAGE Shows the D-PRS comment included in the position data of the received call. *If you have no position - Icom ID-5100A | Full Instruction Manual - Page 263
preloaded into your transceiver. However, if the CPU clears all programmed contents (All Reset), the repeater list is also cleared. We recommend that memory data be backed up using an SD card, or be saved to a PC using the CS5100 cloning software. About the repeater list: The repeater list can be - Icom ID-5100A | Full Instruction Manual - Page 264
to use the FM repeater Frequency offset to use the FM repeater Receiving mode of the FM repeater Tone function setting of the FM repeater REPEATER TONE FM repeater tone frequency (Tone Encoder) setting of the access repeater. POSITION LATITUDE* LONGITUDE* UTC OFFSET Position data accuracy - Icom ID-5100A | Full Instruction Manual - Page 265
up to 8 digits can be entered. Also, a note of up to 4 characters, for operating radio type, area, and so on, can be entered. • See page 6-5 for MY call sign programming. • To select a different My Call Sign, touch the desired call sign to set. TX Message My Station > TX Message The transceiver has - Icom ID-5100A | Full Instruction Manual - Page 266
you push [PTT]. DV Data TX (Default: Auto) DV Set > DV Data TX Select whether to manually or automatically transmit slow-speed data. • PTT: Push [PTT] to manually transmit the data. • Auto: W hen data is input from a PC through the [DATA] jack, the transceiver automatically transmits it. 12 - Icom ID-5100A | Full Instruction Manual - Page 267
Digital Repeater Set (Default: ON) DV Set > Digital Repeater Set Turn the digital repeater setting function ON or OFF. In any DV mode except when using the DR function, and when accessing a repeater that has a call sign that is different than the transceiver The transceiver can record the data of - Icom ID-5100A | Full Instruction Manual - Page 268
call sign is always announced. NOTE: • When the digital squelch function is used, the call- ing station's call sign is not using the DR function, the frequency is announced if the FM repeater does not have a call sign. NOTE: When you receive a signal during an announcement, the transceiver - Icom ID-5100A | Full Instruction Manual - Page 269
Alphabet Select either "Normal" or "Phonetic Code" to announce the alphabet characters. • Normal : Normal code is used. (for example: A as eh, B as bee) • Phonetic Code : Phonetic code is used. (for exam- ple: A as Alfa, B as Bravo) SPEECH Speed (Default: Fast) SPEECH > SPEECH Speed Set - Icom ID-5100A | Full Instruction Manual - Page 270
Previous view 12 MENU SCREEN DTMF items You can set the DTMF tone code and DTMF memory channel for DTMF tone operation. See pages 13-5 to 13-7 for details. DTMF Memory (Default: d0) DTMF > DTMF Memory Shows a list of the DTMF memory channels. • d0 to d# : DTMF memory channel list DTMF Speed - Icom ID-5100A | Full Instruction Manual - Page 271
- tory log on the SD card. The transceiver starts making a receive history log when you finish talking. NOTE: • The folder name is automatically created, as [ID-5100\RxLog]. • The file name is automatically created, as shown in the example below: Log start date and time: 2014/4/1 15:30:00 File - Icom ID-5100A | Full Instruction Manual - Page 272
reception Date 4/1/2014 13:51:48 4/1/2014 13:51:48 Date and time (in twelve levels) RPT Call Sign JP3YHJ A JP3YHJ A Repeater call sign (DV mode only) TX Call Sign CQCQCQ ( Sign (Blank) JA3YUA A/ RX Call sign (DV mode only) ID-5100 RX Latitude (Blank) 34.764667 Caller's latitude, if sent. - Icom ID-5100A | Full Instruction Manual - Page 273
STAR! Message included in the received call (up to 20 characters) Status (Blank) Normal: blank, Uplink: "RPT UP", Access repeater reply: "UR?" or "RPT?" Received date 12/23/2012 13:51:48 Date Time data that the caller station acquires the position data GPS Message Osaka City/ID-5100 Caller - Icom ID-5100A | Full Instruction Manual - Page 274
rotate [DIAL]. • OFF: Turns OFF the function. • ON: Turns ON the function. Auto Repeater Function > Auto Repeater This item appears only in the Korean and U.S.A. ver- sion transceivers. The Auto repeater function automatically turns the du- plex operation and tone encoder* ON or OFF. The - Icom ID-5100A | Full Instruction Manual - Page 275
channel, repeater or station call sign. N/A N/A ● DOWN Push to decrease the frequency, Memory channel, repeater or station band. BAND/BANK In the VFO mode, push to change the operating band, and in the Memory Bank mode, push to select Bank A to Z, or OFF. ● • Only the programmed - Icom ID-5100A | Full Instruction Manual - Page 276
Digital Code Squelch) "CSQL" (Digital Code Squelch) In the VFO mode or in the DR screen, hold down to save the fre- MW quency displayed in the MAIN band . Hold down for 1 second to repeatedly transmit the voice audio. Voice TX (T1) • This key function can also be used in the DR screen. If - Icom ID-5100A | Full Instruction Manual - Page 277
holding down the [PTT] button. • OFF: Push [PTT] to transmit and release to receive. • ON: Push [PTT] to transmit, then push again to transceiver's operation by touching on the SUB band screen. • Main Select: Changes to the MAIN band. • Function Select: T ouch operation is activated on the SUB band - Icom ID-5100A | Full Instruction Manual - Page 278
-speed data communication in the DV mode to 4800 bps or 9600 bps. CI-V Address (Default: 8Ch) Function > CI-V > CI-V Address To distinguish equipment, each CI-V transceiver has its own Icom standard address in hexadecimal code. The ID-5100A/E's default address is 8Ch. When 2 or more ID-5100A/Es - Icom ID-5100A | Full Instruction Manual - Page 279
turned ON continuously while the transceiver is turned ON. • Auto programmed name after the call sign. RX Position Indicator (Default: ON) Display > RX Position Indicator Select whether or not to display " " (RX position indicator) when the signal received in the DV mode contains position data - Icom ID-5100A | Full Instruction Manual - Page 280
the caller's position, re- ceived in only the MAIN band. You can set the display time period in the the transceiver displays the name after the call sign in any DV mode except when using the DR displayed. • ON: Icom logo, MY call sign, the product model ("ID- 5100A" or "ID-5100E")* are displayed. * - Icom ID-5100A | Full Instruction Manual - Page 281
or Japanese. System Language (Default: English) Display > System Language Set the system language of the transceiver to English or Japanese. • English: The system language of the transceiver is English. - Only alphabetical characters (A to Z, a to z, 0 to 9) and symbols can be displayed. If - Icom ID-5100A | Full Instruction Manual - Page 282
in only Japanese characters. There will be no English item names. Unless you are fluent in reading Japanese characters, use this feature with extreme caution. If you change the transceiver's language to Japanese, and can't understand the menu system in the new setting, you will have to change the - Icom ID-5100A | Full Instruction Manual - Page 283
Memory mode and the DR function. (p. 2-16) Band Edge Beep (Default: OFF) Sounds > Band Edge Beep Turn the Band edge beep ON or OFF. • OFF: N o A beep sounds when you tune into or out of the AIR, VHF and UHF band's frequency range by rotating [DIAL]. Scan Stop Beep (Default: OFF) Sounds > - Icom ID-5100A | Full Instruction Manual - Page 284
DATE Time Set > Date/Time > DATE Manually set the date to between 2000/01/01 and 2099/12/31. TIME Time Set > Date/Time > TIME Manually This function can correct the time by using the time information that a GPS sentence transceiver during this period, the Auto Power OFF timer will be reset. 12-62 - Icom ID-5100A | Full Instruction Manual - Page 285
Import/Export > Export Export the UR call sign, repeater list or GPS memory data in the CSV format file. Separator/Decimal (Default: may differ, depending on the transceiver version. Date (Default: mm/dd/yyyy*) SD Card > Import/Export > CSV Format > Date Select the date format between "yyyy/mm/ - Icom ID-5100A | Full Instruction Manual - Page 286
is connected. • Headset Only: Outputs audio to only the con- nected Bluetooth® headset. • Headset & Speaker: Outputs audio to both the con- nected Bluetooth® headset and the transceiver's speaker. VOX (Default: OFF) Bluetooth Set > Headset Set > VOX > VOX The VOX (Voice Operated Transmission - Icom ID-5100A | Full Instruction Manual - Page 287
items (Continued) Power Save (Default: OFF) Bluetooth Set > Headset Set > Icom Headset > Power Save Select whether or not to operate with the power save mode while the optional VS-3 Bluetooth® headset is connected. When a third-party headset or a data device is connected, the power save mode is - Icom ID-5100A | Full Instruction Manual - Page 288
can also be used in the DR screen. If the voice audio is not stored in the [T1] (Voice memory number for TX) in the Voice TX record screen, this function is disabled. Push to transmit a 1750 Hz tone. Serialport Function (Default: CI-V (Echo Back OFF)) Bluetooth Set > Data Device Set > Serialport - Icom ID-5100A | Full Instruction Manual - Page 289
transceiver firmware's version number. When the optional UT-133 Bluetooth® unit is installed, the unit's version number is also displayed. Clone Mode Others > Clone > Clone Mode Select to enter the clone mode to read or write the CS5100 data from or to the PC. See page 13-12 for details. - Icom ID-5100A | Full Instruction Manual - Page 290
mode 13-11 DDExiting the Repeater mode 13-11 DDCross-Band repeater operation 13-11 Cloning function 13-12 DDTransceiver-to-Transceiver cloning using an SD card........... 13-12 DDCloning from a PC using an SD card 13-15 DDCloning from a PC using an optional cloning cable 13-15 Remote jack (CI - Icom ID-5100A | Full Instruction Manual - Page 291
can be used for repeatedly calling CQ or for other events. When the key function [Voice TX (T1)] is assigned to a microphone key, push the key to transmit the stored audio in the [T1] (Voice memory number for TX). (p. 1254) NOTE: Be sure to first insert an SD card into the transceiver. DDRecording - Icom ID-5100A | Full Instruction Manual - Page 292
voice transmission. The transceiver repeatedly transmits the recorded voice audio at 5 second intervals as the default. • Using the TX Monitor function But if the squelch is manually opened in the FM mode, the voice audio is repeatedly transmitted, according to the repeat time setting. • Y - Icom ID-5100A | Full Instruction Manual - Page 293
sign when using the DR sign selected in the MAIN band. • When you receive CS] for 1 second, and then release it, the Speech function audibly announces the an announce- ment, the transceiver cancels the announcement, and function that announces the frequency or repeater call sign that is selected by - Icom ID-5100A | Full Instruction Manual - Page 294
Previous view 13 OTHER FUNCTIONS Using the DTMF memory The transceiver can store up to 16 memory channels of 24-digit DTMF code. DDEntering DTMF code qqTouch [MENU]. wwTouch "DTMF Memory." (DTMF > DTMF Memory) • If the item is not displayed, touch [∫] or [√] one or more times - Icom ID-5100A | Full Instruction Manual - Page 295
Previous view 13 OTHER FUNCTIONS Using the DTMF memory (Continued) DDTransmitting DTMF code qqTouch the Function forwards. • Touch [CLR] to delete the selected character, symbol or number. ttAfter entering all digits, touch [TX] or push [PTT]. • The DTMF code is transmitted. The DTMF code - Icom ID-5100A | Full Instruction Manual - Page 296
Previous view 13 OTHER FUNCTIONS Using the DTMF memory (Continued) DDSetting the DTMF transmit speed The DTMF transmit speed can be selected. qqTouch [MENU]. wwTouch "DTMF Speed." (DTMF > DTMF Speed) • If - Icom ID-5100A | Full Instruction Manual - Page 297
narrow) mode. eeRotate [DIAL] to select a desired operating frequency. 2. Using the tone squelch iiTouch the Function group icon one or more times. • the screen to stop the beeps. ("S" disappears) After that, the transceiver selects the regular tone squelch operation. If you make no operation - Icom ID-5100A | Full Instruction Manual - Page 298
FM or FM narrow mode. You can silently wait for calls from others using the same tone. Also, a reversed tone squelch function will mute the touch the screen to stop the beeps. ("S" disappears) After that, the transceiver selects the regular DTCS squelch operation. If you make no operation for - Icom ID-5100A | Full Instruction Manual - Page 299
beep sounds until you change the operating mode or weather channel, turn OFF the Weather Alert function, or turn OFF the transceiver. The previously selected (used) weather channel is checked periodically during standby, or while scanning. qqTouch [QUICK]. wwTouch "Weather Alert." • If the item is - Icom ID-5100A | Full Instruction Manual - Page 300
version only) When you receive an FM (or FM-N) signal in the Repeater mode on one band, the transceiver automatically retransmits them on the other band. This is called Cross-Band repeater operation. NOTE: Use this function carefully according to the applicable laws and ordinances. DDEntering the - Icom ID-5100A | Full Instruction Manual - Page 301
13 OTHER FUNCTIONS Cloning function The ID-5100A/E has a data cloning capability. This function is useful when you want to copy all of the programmed contents from one ID-5100A/E to another. Cloning can also be done with a PC. • T ransceiver-to-Transceiver cloning using an SD card (described on - Icom ID-5100A | Full Instruction Manual - Page 302
DDTransceiver-to-Transceiver cloning using an SD card (Continued) yyTouch [YES]. 3. Loading the setting data into the sub transceiver. !1 signs, into the transceiver. • Repeater List Only: L oads only the repeater list into the transceiver. • The "Keep 'SKIP' setting in Repeater List?" appears. - Icom ID-5100A | Full Instruction Manual - Page 303
view 13 OTHER FUNCTIONS Cloning function DDTransceiver-to-Transceiver cloning using an SD card (Continued) !6 Touch [Yes]. • While checking the file, "FILE CHECKING" and a progress bar are displayed. !7 After checking, settings data loading starts. • While loading, "LOADING" and a progress - Icom ID-5100A | Full Instruction Manual - Page 304
OPC-2218LUto othreOCaPrdC-478UC instruction manual (downloaded fromreathdeer Icom WEB site; http:// www.icom.co.jp/world/) Cloning cable NOTE: When using the OPC-2218LU or OPC-1529R, set the "DV Data TX" item to "PTT," before cloning. If "Auto" is set, the transceiver may automatically transmit - Icom ID-5100A | Full Instruction Manual - Page 305
transceiver. Up to 4 Icom CI-V transceivers or receivers can be connected to the PC. See page 12-56 for setting the CI-V condition using the set mode. Power source DC 9-15 V 3 conductor 3.5 (d) mm plug PC RS-232C cable CT-17 to [SP2] *% 2 conductor 3.5 (d) mm plug • Connections (ID-5100A - Icom ID-5100A | Full Instruction Manual - Page 306
, 02 Send/read GPS TX mode (00=OFF, 01=D-PRS, 02=NMEA) 18 00 Turning the transceiver power OFF 01 Turning the transceiver power ON*2 19 00 Read transceiver ID 1B 00 see p. 13-18 Send/read Repeater tone frequency 01 see p. 13-18 Send/read Tone squelch frequency 02 see p. 13-18 Send/read - Icom ID-5100A | Full Instruction Manual - Page 307
XX t 04 • Repeater tone/tone squelch frequency setting Command: 1B 00, 1B 01 q* w e 0 0 X X X X Fixed: 0 Fixed: 0 100 Hz digit 10 Hz digit 1 Hz digit 0.1 Hz digit 10H zdigit ɿ0, 3, 5, 6 (according to the 100 Hz digit) 1 Hz digit ɿ0 (Fixed) 1 kHz digit ɿ0, 1, 2, 3, 5, 6, 7, 8 100 Hz - Icom ID-5100A | Full Instruction Manual - Page 308
bit2 0/1 0=No Break-in, 1=Break-in bit1 0/1 0=Data, 1=Control bit0 0/1 0=Normal, 1=EMR w Header flag data (Second byte) Data Description bit2 bit1 bit0 1 1 1 Repeater control 1 1 0 Send auto acknowledge 1 0 1 (Not used) 1 0 0 Request to re-transmit 0 1 1 Send acknowledge - Icom ID-5100A | Full Instruction Manual - Page 309
the transceiver power repeater you received the call from • DV RX Status setting Command: 20 0201, 20 0202 Data Function Description bit7 0 (Fixed) - bit6 0/1 Receiving a During receiving a digital steps) @9-#1: Speed (0.1 km/h steps) #2-#8: Date (UTC: yyyymmddHHMMSS) *y: Year, m: Month, - Icom ID-5100A | Full Instruction Manual - Page 310
@7, @8: Course (1 degree steps) @9-#1: Speed (0.1 km/h steps) #2-#8: Date (UTC: yyyymmddHHMMSS) *y: Year, m: Month, d: Day, H: Hour, to the right) $1: Gain (see the table to the right) $2: Directivity (see the table to the right) Data 0 1 2 3 4 5 6 7 8 9 Power (W) 0 1 4 9 16 25 36 49 64 - Icom ID-5100A | Full Instruction Manual - Page 311
-EFh) • DV TX data, DV RX data (transceive) Command: 22 00, 22 01 01 q-#0 X X X X Varible q-#0: Tx, data Rx data (Up to 30 Byte) (0.1 km/h steps) @1-@7: Date (UTC: yyyymmddHHMMSS) *y: Year, m: Month, d: Day, H: Hour, M: Minute, S: Second • Manually input position data Command: 23 02 q-t - Icom ID-5100A | Full Instruction Manual - Page 312
pen being careful to not damage the screen. • When touched, the dot appears on another place. Dot rrRepeat step w. • When the calibration is completed, the transceiver returns to the previous screen. 13-23 - Icom ID-5100A | Full Instruction Manual - Page 313
Previous view Section 14 OPTIONS Options 14-2 14-1 - Icom ID-5100A | Full Instruction Manual - Page 314
cable USB type Allows data cloning operation with the CS-5100. *The OPC-478UC and OPC-2218LU cannot be used with the Windows® 8.1. (As of March 2014) • OPC-1156 controller extension cable Cable length: 3.5 m (11.4 ft) • CT-17 ci-v level converter unit For remote transceiver control using - Icom ID-5100A | Full Instruction Manual - Page 315
15-10 DDAF Output 15-10 DDAbout the Icom headset (VS-3 15-10 Downloading the RS-MA1A from the Google Play store....15-11 DDRequired items 15-11 DDDownload procedures 15-11 Connecting to a Bluetooth® device 15-12 DDPairing with the data device 15-12 DDConnection 15-14 Disconnecting from - Icom ID-5100A | Full Instruction Manual - Page 316
When you install the optional UT-133 Bluetooth® unit in the transceiver, you can connect to other Bluetooth® devices. In this section, the ID-5100A/E with the UT-133 is described as simply "transceiver." You can connect other devices to the transceiver. • Icom Headset When you connect the VS - Icom ID-5100A | Full Instruction Manual - Page 317
cause a fire or damage the transceiver. Place the transceiver in a secure place to avoid inadvertent use by children. R WARNING! Immediately turn the transceiver power OFF and remove the power cable if it emits an abnormal odor, sound or smoke. Contact your Icom dealer or distributor for advice. DO - Icom ID-5100A | Full Instruction Manual - Page 318
use a Bluetooth® device, pay attention to the following: Bluetooth® devices operate on the 2.4 GHz band. The 2.4 GHz band is also used by other devices, such as Wireless LAN products, microwave ovens, RFID systems, amateur radio stations, and so on. When using the receiving antenna. • Icom - Icom ID-5100A | Full Instruction Manual - Page 319
communicate with other Bluetooth® device. NOTE: Before touching the transceiver or UT-133, remove static electricity from your body by touching a grounded object such as a grounded piece of equipment. The static electricity from your body may damage the transceiver or unit, or lose data. qqTurn the - Icom ID-5100A | Full Instruction Manual - Page 320
use the device within the range. 1. Selecting the pairing mode on the headset. See the instruction manual of the headset to select the pairing mode. 2. Searching for the headset (Transceiver) qqHold down [ ] to turn ON the power. wwTouch [MENU]. eeTouch "Bluetooth." (Bluetooth Set > Bluetooth - Icom ID-5100A | Full Instruction Manual - Page 321
last paired device. For your reference: When the transceiver cannot find any available headset, and "No Device Found" is displayed on the screen, touch [QUICK], and then touch "Re-search" to search again for a headset. After connecting to the Bluetooth® device, the dialog box opens, as show above - Icom ID-5100A | Full Instruction Manual - Page 322
, even if the "VOX" item is set to ON. Be sure to check the Bluetooth® connection between the transceiver and the headset before using the VOX function. DDSetting the VOX level qqTouch [MENU]. wwTouch "VOX Level." (Bluetooth Set > Headset Set > VOX > VOX Level) • If the item is not displayed, touch - Icom ID-5100A | Full Instruction Manual - Page 323
OPERATION VOX function (Continued) DDVOX-related settings You can set the "VOX Delay" and "VOX Time-Out Timer" in the Menu screen. (Bluetooth Set > Headset Set > VOX > VOX Delay) (Bluetooth Set > Headset Set > VOX > VOX Time-Out Timer) • VOX Delay (p. 12-64) The VOX delay is the amount of time the - Icom ID-5100A | Full Instruction Manual - Page 324
MENU]. • Closes the Menu screen. • Audio is heard from both the connected Bluetooth® headset and the transceiver's speaker. DDAbout the Icom headset (VS-3) You can set the detailed settings of the optional VS-3 Bluetooth® headset. Also, you can assign the desired key function to [PLAY], [FWD] and - Icom ID-5100A | Full Instruction Manual - Page 325
view 15 Bluetooth® OPERATION Downloading the RS-MA1A from the Google Play store The RS-MS1A is a freeware application for Android® devices. With the RS-MS1A, you can use the extended DSTAR® functions to exchange image files or text messages, or display the received D-PRS station data on a map - Icom ID-5100A | Full Instruction Manual - Page 326
the displayed time period. When the time runs out, the transceiver exits the Pairing reception mode. 4. Turning ON the Bluetooth® (Android® device) ttTurn ON Bluetooth® with your Android® device. • See the instruction manual of the Android® device for details. • T he Android® device displays - Icom ID-5100A | Full Instruction Manual - Page 327
the "Connection request received from ICOM BT001. Confirm the following passkey is shown. Passkey: MMMMM" dialog box on the transceiver. NOTE: Depending on the Android® device, you may not be able to pair with the Bluetooth® device. 6. Receiving a pairing request (Transceiver) uuWhen the - Icom ID-5100A | Full Instruction Manual - Page 328
"(Connect)" appears. Appears while connected Data device icon Bluetooth® address • While connected, the Bluetooth® icon appears. Appears while connected to the Bluetooth® device NOTE: If you cannot connect, check that the same CI-V address is set between the transceiver and the RSMS1A. You can - Icom ID-5100A | Full Instruction Manual - Page 329
® device. rrTouch [YES]. "(Connect)" disappears • The transceiver disconnects from the Bluetooth® device, and "(Connect)" disappears from the list. However, the transceiver is still paired with the Bluetooth® device. • When you touch the unconnected Bluetooth® device displayed in the pairing list - Icom ID-5100A | Full Instruction Manual - Page 330
[∫] or [√] one or more times to select another page. eeRotate [DIAL] to select the Bluetooth® device to de- lete. rrTouch [QUICK]. ttTouch "Delete." yyTouch [YES]. • Deletes the first pair with it again. Bluetooth® connection (Headset): p. 15-6 Bluetooth® connection (Data device): p. 15-2 15-16 - Icom ID-5100A | Full Instruction Manual - Page 331
® unit You can initialize the installed UT-133 Bluetooth® unit. You should initialize the unit if you have trouble during Bluetooth® operation. When you do a partial reset or all reset, the Bluetooth® settings returns to their factory defaults. However, the device name and pairing/connection - Icom ID-5100A | Full Instruction Manual - Page 332
® OPERATION The maximum number of paired devices You can pair two types of the Bluetooth® devices: Headset and Data device. Up to eight Bluetooth® devices can be paired with the UT-133 Bluetooth® unit. However, you cannot pair with eight headsets only, or eight data devices only. Displays the paired - Icom ID-5100A | Full Instruction Manual - Page 333
Previous view Section 16 SPECIFICATIONS Specifications 16-2 DDGeneral 16-2 DDTransmitter 16-3 DDReceiver 16-3 16-1 - Icom ID-5100A | Full Instruction Manual - Page 334
program scan channels: 25 channels (2 edge frequencies in each channel) • No. of call channels: 4 channels (2 channels × 2 bands) • Antenna connector: SO-239 • Antenna : 1.3 kg; 2.9 lb 260 g; 9.2 oz All stated specifications are typical and subject to change without notice or obligation. 16 - Icom ID-5100A | Full Instruction Manual - Page 335
≥ 60 dB ≥ 55 dB ≥ 50 dB • Spurious and image rejection ratio: ≥ 60 dB ≥ 55 dB (A band UHF) • AF output power: ≥ 2 .0 W (at 10% distortion with an 8 ø load) • AF output impedance: 8 ø All stated specifications are typical and subject to change without notice or obligation. 16-3 - Icom ID-5100A | Full Instruction Manual - Page 336
Previous view Section 17 MAINTENANCE Resetting the CPU 17-2 DDPartial Reset 17-2 DDAll reset 17-3 Troubleshooting 17-4 DDWhile operating D-STAR 17-4 DDWhile operating GPS logger 17-5 DDTransceiver power 17-5 DDTransmit and receive 17-5 DDDisplay 17-6 DDScanning 17-6 17-1 - Icom ID-5100A | Full Instruction Manual - Page 337
. If the problem is still there, perform a Partial reset or an All reset. DDPartial Reset qqTouch [MENU]. wwTouch "Partial Reset." (Others > Reset > Partial Reset) • If the item is not displayed, touch [∫] or [√] one or more times to select the page. eeTouch [YES]. • The transceiver displays - Icom ID-5100A | Full Instruction Manual - Page 338
because the repeater list will be cleared. So we recommend you save the programmed data onto an SD card, or to your PC using the CS-5100 cloning software (contained in the CD) before performing an All reset. After the All reset is finished, load or write the saved data into your transceiver. qqTouch - Icom ID-5100A | Full Instruction Manual - Page 339
Troubleshooting The following chart is designed to help you correct problems which are not equipment malfunctions. If you are unable to locate the cause of a problem, or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center. DDWhile operating D-STAR PROBLEM - Icom ID-5100A | Full Instruction Manual - Page 340
is set. (CSQL) is impossible. • Set the correct digital code. p. 7-17 You don't know how to up- - date the repeater list. • See "Updating the repeater list" to p. 6-35 check. DDWhile operating GPS logger PROBLEM POSSIBLE CAUSE SOLUTION Position data cannot be re- • The "GPS Select" item - Icom ID-5100A | Full Instruction Manual - Page 341
. • Reset the transceiver. p. 17-2 erroneous. • External factors have caused the fault. • Disconnect and connect to the DC - power supply. Cannot receive on the SUB • The SUB band mute is activated. band. • T urn OFF the function. p. 12-61 DDDisplay PROBLEM POSSIBLE CAUSE SOLUTION - Icom ID-5100A | Full Instruction Manual - Page 342
cloning cable 13-15 Using an SD card 13-15 Transceiver-to-Transceiver cloning Using an SD card 13-12 Comment Item 12-27 Object 12-24 Position 12-22 Weather 12-30 Controller Display (Touch screen 1-3 Front panel 1-2 Course Item 12-28 Object 12-25 Cross-Band repeater operation - Icom ID-5100A | Full Instruction Manual - Page 343
Item 12-28 Object 12-25 Position 12-23 Data Speed 12-56 Data Type Item 12-27 Object 12-24 Date 12-49, 12-62, 12-63 Dial Speed-UP 12-52 Digital Monitor 12-45 Digital Repeater Set 12-45 Digital squelch functions 7-16 Digital call sign squelch setting 7-16 With a Pocket beep 7-16 - Icom ID-5100A | Full Instruction Manual - Page 344
11 Manual Position 12-20 Rearranging the display order 8-35 Saving your own or received position data... data 8-34 Displaying Position Data 8-4 Displaying your position using a mapping program -26 Position 12-23 Heterodyne A BAND UHF 12-56 A BAND VHF 12-56 B BAND UHF 12-56 Home channel Home - Icom ID-5100A | Full Instruction Manual - Page 345
63 Lock function 2-13 Low-speed data communication 7-15 Application setting 7-15 Connection 7-15 M MAIN band selection 2-15 Main unit - Front Entering the Menu screen 12-2 Menu items and Default settings 12-3 Bluetooth Set items 12-64 Call Sign items 12-37 Display items 12-57 - Icom ID-5100A | Full Instruction Manual - Page 346
data 6-33 Requesting repeater information 6-34 Unlinking a reflector 6-33 Using a reflector 6-32 Repeater List... 7-21 Rearranging the display 7-27 Repeater detail screen 7-31 Repeater group name programming 7-30 Required items for the communication cases...... 7-21 Updating 6-35 Repeater - Icom ID-5100A | Full Instruction Manual - Page 347
Call Sign 12-57 RX Call Sign SPEECH 12-46 RX>CS SPEECH 12-46 RX History Adding the Repeater information 7-28 RX History items 12-38 RX History Log 12-49 Using the RX History 6-11 View in the RX History screen 7-6 RX Position Display 12-58 RX Position Display Timer - Icom ID-5100A | Full Instruction Manual - Page 348
7-4 Transmitting D-PRS data 8-15 Transmitting GPS data (D-PRS and NMEA)...... 8-14 Transmitting NMEA data 8-27 Transmitting on an Amateur band 2-12 Troubleshooting 6-16, 17-4 Display 17-6 Scanning 17-6 Transceiver power 17-5 Transmit and receive 17-5 While operating D-STAR 17-4 While - Icom ID-5100A | Full Instruction Manual - Page 349
Weather channel mode selection 2-9 Weather channel operation 13-10 Weather channel selection 13-10 Weather Confirming the weather data input 8-25 Weather setting (D-PRS 8-23 Weather data content 8-25 Weather station transmission 8-25 Y Your Call Sign 12-41 Your setting is correct 7-36 VIII - Icom ID-5100A | Full Instruction Manual - Page 350
A-7115-3EX © 2014 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan - Icom ID-5100A | Full Instruction Manual - Page 351
PRÉCAUTIONS ÉMETTEUR-RÉCEPTEUR DOUBLE BANDE ID-5100A Merci d'avoir choisi un produit Icom. LIRE ATTENTIVEMENT ET INTEGRALEMENT CE MANUEL en cours d'émissioNE JAMAIS permettre le contact d'un objet metallique, d'un cable ou d'autres objets avec un des composants internes ou des connecteurs de la - Icom ID-5100A | Full Instruction Manual - Page 352
Icom (fourni d'origine ou en option). La repartition des broches des microphones des autres fabricants est différente et leur connexion à l'ID5100A peut endommager l'émetteur-récepteur. Pour l'opération Bluetooth le contact d'un objet metallique, d'un cable ou d'autres objets avec un des composants
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
 |
 |
FULL MANUAL
ID-5100A
ID-5100E
15 Bluetooth
®
OPERATION
14 OPTIONS
13 OTHER FUNCTIONS
12 MENU SCREEN
11 REPEATER AND DUPLEX OPERATIONS
10 VOICE MEMORY
9
USING AN SD CARD
8
GPS OPERATION
7
D-STAR OPERATION <ADVANCED>
6
D-STAR OPERATION <BASIC>
5
PRIORITY WATCH
4
SCAN OPERATION
3
MEMORY OPERATION
2
BASIC OPERATION
1
PANEL DESCRIPTION
16 SPECIFICATIONS
17 MAINTENANCE
INDEX
INTRODUCTION
To update the repeater list,
click here!
DUAL BAND TRANSCEIVER