Icom MA-500TR Instruction Manual

Icom MA-500TR Manual

Get Icom MA-500TR PDF manuals and user guides View all Icom MA-500TR manuals
Add to My Manuals
Save this manual to your list of manuals

Icom MA-500TR manual content summary:

  • Icom MA-500TR | Instruction Manual - Page 1
    INSTRUCTION MANUAL CLASS B AIS TRANSPONDER MA-500TR This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
  • Icom MA-500TR | Instruction Manual - Page 2
    purchasing this Icom product. The MA-500TR class b ais transponder is designed and built with Icom's state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We appreciate you making the MA-500TR your transponder of choice
  • Icom MA-500TR | Instruction Manual - Page 3
    has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules washers (M5) MXG-5000 gps receiver is included with MA-500TR. MXG-5000 (Referred to as Internal GPS) Cable length: Approx. 10 m (32.8 ft) • An instruction sheet comes with the MXG-
  • Icom MA-500TR | Instruction Manual - Page 4
    RADIO OPERATOR WARNING Icom requires the radio operator to meet the FCC Requirements for Radio Frequency Exposure. An omnidirectional antenna with gain not greater than 9 dBi must be mounted a
  • Icom MA-500TR | Instruction Manual - Page 5
    types of transmitter, SSB, CW, AM, etc. have a lower 'average' output power and the perceived risk is even lower. 1 CE versions of the MA-500TR which display 2 the "CE" symbol on the serial number label, 3 comply with the essential requirements of the European Radio and Telecommunication Ter
  • Icom MA-500TR | Instruction Manual - Page 6
    been performed. Kind of equipment: CLASS B AIS TRANSPONDER Type-designation: ma- 500tr Version (where applicable): This compliance is ) vii) viii) 0560 Bad Soden 2nd Dec. 2010 Place and date of issue Icom (Europe) GmbH Communication Equipment Auf der Krautweide 24, 65812 Bad Soden am Taunus,
  • Icom MA-500TR | Instruction Manual - Page 7
    cannot be guaranteed because of possible damage to the transponder's case or the waterproof seal. * Except for the DC power and cloning cable connectors. For U.S.A. only CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this
  • Icom MA-500TR | Instruction Manual - Page 8
    28-34 ■ General 28 ■ Menu mode items 28 7 INSTALLATION AND CONNECTIONS 35-42 ■ Connections 35 ■ Fuse replacement 38 ■ Antenna 38 ■ Transceiver connection 39 ■ Mounting the transponder 41 ■ MB-75 installation 42 8 MAINTENANCE 43-45 ■ Troubleshooting 43 ■ Error message 44 ■ Diagnostics
  • Icom MA-500TR | Instruction Manual - Page 9
    received data on a plotter or a radar screen. Other vessel (Class B AIS) Other vessel (Class A AIS) Vessel information Your vessel (Class B AIS) Base Station D AIS Classes 1 There are four types of AIS below, are required to install a 6 Class A AIS transponder: • Upwards of 300 gross tonnage
  • Icom MA-500TR | Instruction Manual - Page 10
    w LEFT AND RIGHT KEYS Common> While in the Menu item setting mode, push to select a menu option. (pp. 29, 33) ➥ P ush [Ω] to sequentially select each AIS target icon far- thest from your vessel (or waypoint, if it is set; see page 24 for setting detail). (p. 15) ➥ P ush
  • Icom MA-500TR | Instruction Manual - Page 11
    return to the pre- 2 vious screen. (pp. 10, 13, 23) ➥ W hile in the Menu mode, push to exit it, and return to the previous screen. (pp. 9, 28) ➥ P ush to DSC call to the selected AIS target. (p. 22) This function is available only when a transceiver is connected to the transponder. (p. 39) i POWER
  • Icom MA-500TR | Instruction Manual - Page 12
    can select your desired type using the [DISP MODE] key. NOTE: When one of the transponder is turned ON, the plotter display automatically appears, if the GPS receiver is connected and it receives vessel to the selected AIS target. ➥ S hows TCPA information of the selected AIS target whose CPA is
  • Icom MA-500TR | Instruction Manual - Page 13
    the plotter display. • W hen your vessel moves less than 2 knots, the icon is displayed as " ." u KEY ENTRY GUIDE Shows the key entry guide. ➥ P ush [Ω] or [≈] to select each AIS target icon (or waypoint), in sequence. (p. 15) • A target box will appear around the selected target icon. ➥ P ush
  • Icom MA-500TR | Instruction Manual - Page 14
    [DISP MODE] to switch to the target list display, which shows all AIS targets being detected by the transponder. The AIS target OF DANGEROUS TARGETS Shows the number of AIS targets which are being detected by the transponder. w KEY ENTRY GUIDE Shows the key entry guide. ➥ P ush [Ω] or [≈] to
  • Icom MA-500TR | Instruction Manual - Page 15
    second to turn OFF the power, then ON again to reset the transponder. If there is no change, contact your dealer or service center. 1 2 3 4 5 6 e A fter the opening In this case, the transponder operates as just an AIS receiver. 10 11 12 13 14 15 16 ☞ Continued on the next page. 7
  • Icom MA-500TR | Instruction Manual - Page 16
    code setting mode. t P ush [∫] or [√] to input the specific 9-digit MMSI code. • Push [≈] to move the cursor forward. • Push [Ω] to move the cursor backward. • Push [CLEAR] to cancel, and go to the plotter display. In this case, the transponder operates as just an AIS receiver. ENT] [CLEAR
  • Icom MA-500TR | Instruction Manual - Page 17
    5 NOTE: After the MMSI code programming, the transponder automatically enters the Initial setting mode. In this D Name Enter the vessel's name w. See page 13 for setting details. 7 q P ush [MENU] to enter the Menu mode. D Call Sign 8 w P ush [∫] or [√] to select "Initial Setting," then push
  • Icom MA-500TR | Instruction Manual - Page 18
    shows the internal GPS antenna set screen. To show the external GPS antenna set screen, select "Set 10 EXT GPS POS" in the "Initial Setting" mode. (p. 9) D Type of Ship Select your vessel type. ➥ Push [∫] or [√] to select your vessel type from the list, then push [ENT] to save and return to
  • Icom MA-500TR | Instruction Manual - Page 19
    . NMEA2 is used for communication between the transponder and the Icom MarineCommander™ system or a GPS receiver. q P ush [∫] or [√] to set another port. r P ush [CLEAR] to save and return to the Initial setting mode. ENT] [CLEAR] 1 • GPS Input1/GPS Input2/GPS Input3 2 Set the NMEA1, NMEA2
  • Icom MA-500TR | Instruction Manual - Page 20
    information is received. The output of GPS in- formation has priority, so the NMEA2 output port may not send some AIS information cor- rectly. However, the transponder displays the AIS information on it's LCD correctly. e P ush [CLEAR] to save and return to the Initial setting mode. ENT
  • Icom MA-500TR | Instruction Manual - Page 21
    Sign settings q P ush [∫] or [√] to select the "Set Name" or "Set Call Sign" that you want to program, then push [ENT] to enter the setting mode. [∫] [ENT] [√] w P ush or [≈] to select the desired character in the table, then push [ENT] to input it. • Select " ," then push [ENT] to move the
  • Icom MA-500TR | Instruction Manual - Page 22
    power, then ON again to reset the transponder. If there is no change, contact your dealer or service center. r T he GPS search display appears the Menu mode by pushing [MENU]. (pp. 28, 31) t W hen the GPS receiver receives signals from a satellite, the transponder automatically displays the
  • Icom MA-500TR | Instruction Manual - Page 23
    North up or COG up) to suit your operating style. 4 q Push [DISP MODE] several times to select the plotter dis- 5 play. w P ush [∫] or [√] 17) 16 NOTE: The alarm buzzer sounds when a malfunction occurs or an AIS target is closer than your CPA and TCPA settings, depending on the presetting. (
  • Icom MA-500TR | Instruction Manual - Page 24
    ] to save and return to the Menu mode. t P ush [CLEAR] to exit the Menu mode. ENT] [CLEAR] [MENU] ■ Target list display operation The target list display shows all AIS targets being detected by the transponder, including their range and bearing information. The AIS target data is sorted by the
  • Icom MA-500TR | Instruction Manual - Page 25
    MODE] several times to select the danger list display. • Push [Ω] to sort the AIS target data by CPA. • Push [≈] to sort the AIS target data by TCPA. w P ush [∫] or [√] to select the desired AIS about the selected AIS 2 target. The contents differ, depending on the AIS class. 3 In the
  • Icom MA-500TR | Instruction Manual - Page 26
    4 BASIC OPERATION ■ About the detail screen (Continued) D The detail screens of "Class A" vessels • AIS Class • MMSI Code • Ship Name • Country Name • Call Sign • IMO Number • CPA • TCPA • Latitude • Longitude • Speed Over Ground • Course Over Ground • Heading • Position Accuracy (H: High, L: Low)
  • Icom MA-500TR | Instruction Manual - Page 27
    D The detail screens of "Class B" vessels • AIS Class • MMSI Code • Ship Name • Country Name • Call Sign • Vendor ID • CPA • TCPA • Latitude • Longitude • Speed Over Ground • Course Over Ground • Heading • Position Accuracy (H: High, L: Low) •
  • Icom MA-500TR | Instruction Manual - Page 28
    the detail screen (Continued) D The detail screens of a "Base Station" • AIS Class • MMSI Code • Latitude • Longitude • Position Accuracy (H: High, L: Low) • Range • Bearing D The detail screens of an "SAR" • AIS Class • MMSI Code • Latitude • Longitude • Speed Over Ground • Course Over Ground
  • Icom MA-500TR | Instruction Manual - Page 29
    D The detail screens of an "AtoN" • AIS Class • MMSI Code • CPA • TCPA • Latitude • Longitude • Position Accuracy (H: High, L: Low) • Range • Bearing Detail screen 3/4 Detail screen 2/4 BASIC OPERATION 4 1 2 3 • A : Bow to Antenna 4 • B : Stern to Antenna • C: Port
  • Icom MA-500TR | Instruction Manual - Page 30
    instructions. NOTE: The data communication speed (baud rate) of NMEA1 must be set to 4800 bps to send an Individual DSC call using the transponder. (p. 11) q S elect the desired AIS receiving the acknowledgement from the AIS target, use the transceiver to communicate. See the transceiver's manual
  • Icom MA-500TR | Instruction Manual - Page 31
    can be received from an AIS equipped vessel in the area. When a message is received, a beep transponder automatically stores the last 20 received 3 messages in the log memory. The oldest message is automatically deleted when a new 4 message is received. 5 q P ush [MENU] to enter the Menu mode
  • Icom MA-500TR | Instruction Manual - Page 32
    cancel and return to the previous screen. ENT] [CLEAR] y Push [CLEAR] to return to the previous screen. u Push [CLEAR] three times to exit the Menu mode. 24 y R epeat step t to input a waypoint name of up to 10 characters. u P ush or [≈] to select "FINISH," then push [ENT] to set and return
  • Icom MA-500TR | Instruction Manual - Page 33
    • Push [CLEAR] to cancel and return to the previous screen. 11 [∫] [ENT] 12 [√] 13 [CLEAR] 14 15 16 !5 P ush [CLEAR] twice to exit the Menu mode. Convenient! Each time you hold down of [MOB] also adds a waypoint. See page 26 to edit the waypoint data. 25
  • Icom MA-500TR | Instruction Manual - Page 34
    5 OTHER FUNCTIONS ■ Waypoint (Continued) D Edit a waypoint A waypoint's name, latitude and longitude data can be edited. q Push [MENU] to enter the Menu mode. w Push [∫] or [√] to select "Waypoint," then push [ENT]. e Push [∫] or [√] to select "Edit," then push [ENT]. • The "EDIT WAYPOINT" list is
  • Icom MA-500TR | Instruction Manual - Page 35
    cancel deleting. [ENT i P ush [CLEAR] three times to exit the Menu mode. ■ Lost target 1 A vessel is regarded as a "Lost target" after become a Lost target: 7 Vessel type Except Class B 8 Class B Except Class B : Vessel is at anchor, moored 9 1 Class B and moving less than 3 knots 18
  • Icom MA-500TR | Instruction Manual - Page 36
    ] to exit the Menu mode. [∫] [ENT] [√] [CLEAR] [MENU] ■ Menu mode items The Menu mode contains the following items. Item * • Set Type of Ship* • Set Input/Output* Channel Information Diagnostics • Monitor Test* • Transponder Test* • Version Information* Ref. p. 33 p. 33 p. 34 p. 34 p. 34 pp.
  • Icom MA-500TR | Instruction Manual - Page 37
    appears on the display, and the alarm buzzer sounds* repeatedly when an AIS target is closer than your CPA and TCPA settings, as explained to e Push [CLEAR] to save and return to the Menu mode. ENT] [CLEAR] 1 • Slow Warn The GPS receiver calculated COG data of a vessel that is at 2 anchor
  • Icom MA-500TR | Instruction Manual - Page 38
    OPERATION ■ Menu mode items D CPA/TCPA (Continued) • CPA, TCPA Enter CPA (Closest Point of Approach) and TCPA (Time to CPA) values. These settings help you find a dangerous target to avoid a collision. The icon blinks on the plotter display and/or the alarm buzzer sounds, when the AIS target is
  • Icom MA-500TR | Instruction Manual - Page 39
    the previous page. w Push [CLEAR] to return to the Menu mode. When a non-differential GPS receiver is connected, PA is normally 'L.' However, if the values of " GPS receiver 3 is connected. *Only when the transponder receives the sentence format 4 "GSA" or "GSV" from the external GPS receiver. 5
  • Icom MA-500TR | Instruction Manual - Page 40
    The User setting mode allows you to set the seldom-changed settings, and you can "customize" the transponder operation to suit return to the Menu mode. u Push [CLEAR] to exit the Menu mode. [∫] [ENT] [√] [CLEAR] [MENU] • Key Beep You can select the silent operation, or you can
  • Icom MA-500TR | Instruction Manual - Page 41
    AIS target is closer than your CPA and TCPA settings*. (default) *The alarm buzzer sounds only when the collision alarm function is turned ON. (p. 29) OFF : The alarm buzzer is OFF. • Received Setting 10 mode. i Push [CLEAR] twice to exit the Menu mode. 11 [∫] 12 [ENT] 13 [√] 14
  • Icom MA-500TR | Instruction Manual - Page 42
    MODE OPERATION ■ Menu mode items D User Setting (Continued) - SBAS (Satellite Based Augmentation System) Function The SBAS transmits signals to correct errors and improve accuracy and reliability in data received from regular GPS satellites. When this function is ON, the transponder
  • Icom MA-500TR | Instruction Manual - Page 43
    the cloning cable from this connector to a PC. Ask your dealer for details. w INTERNAL GPS RECEIVER CONNECTOR Connects to the MXG-5000 to receive position data and transmit it with other AIS information. NOTE: Important notes and how to install the MXG5000 are described on the instruction sheet
  • Icom MA-500TR | Instruction Manual - Page 44
    y ANTENNA CONNECTOR Connects to a marine VHF antenna with a PL-259 connector for AIS signal transmission and reception. (p. 38) CAUTION: Transmitting without an antenna may damage the transponder. D High-density D-sub 15 pin assignment trewq !0 o i u y !5 !4 !3 !2 !1 Rear panel view NOTE: The
  • Icom MA-500TR | Instruction Manual - Page 45
    4800 bps (IEC61162-1) and 7 5 NMEA1 IN (+) : Less than 2 mA (at 2 V applied) GBS†, DTM, GNS, GLL 38400 bps (IEC61162-2) received GPS signal includes no GBS sentence, the transponder will not receive the signal from the external GPS receiver. *Sent only when the "AIS+GPS" option is set in "AIS
  • Icom MA-500TR | Instruction Manual - Page 46
    replacement One fuse is installed in the DC power cable. If the fuse blows, track down the source of the problem, have it repaired, and replace the damaged below. - Mount the VHF AIS/radio antennas at least 3 m (9.85 ft.) away from each other. - Mount the VHF AIS/radio antennas as high as possible
  • Icom MA-500TR | Instruction Manual - Page 47
    the leaflet that comes with the transponder for details of 5 the transceivers which can operate with this function. 6 In this section, the connecting instructions of the IC-M504*1, 7 IC-M505*1, IC-M603*2 and IC-M604*2 are described as an example. See the instruction manual of each for transceiver
  • Icom MA-500TR | Instruction Manual - Page 48
    LEAD (Red) NMEA OUT LEAD (White) D IC-M603/M604 GPS receiver/External speaker connector Transceiver's rear panel • NMEA : NMEA OUT (+) Connects to lead 5 of OPC-2014. Transceiver's rear panel • GPS receiver/External speaker connector r NMEAOUT (+) e NMEAOUT (-) q NMEAIN (-) SP (+) SP (-) w
  • Icom MA-500TR | Instruction Manual - Page 49
    5 (5 × 20 mm) to a surface which is more than 10 mm (13⁄32 in) thick and can support more than 3 kg (6 lb 61 oz). 6 w A ttach the transponder to the bracket so that the face of 7 the transponder is at 90° to your line of sight when operating it. 8 9 About the installation distance from the
  • Icom MA-500TR | Instruction Manual - Page 50
    (M5 × 8 mm) on either side of the transponder. r A ttach the clamps on either side of the transponder. • Make sure that the clamps align parallel to the transponder's body. 42 y Locking nut t End bolt u C onnect the antenna, power cable, GPS receiver and OPC-2014, then return the instrument
  • Icom MA-500TR | Instruction Manual - Page 51
    malfunctions. If you are unable to locate the cause of a problem or solve 2 it through the use of this chart, contact your nearest Icom 3 Dealer or Service Center. 4 PROBLEM POSSIBLE CAUSE SOLUTION REF. 5 The transponder does not • Bad connection at the power source. • C heck the
  • Icom MA-500TR | Instruction Manual - Page 52
    received. NO GPS DATA RX MALFUNCTION Appears when the transponder receive cir when the protective circuit cuts off the AIS signal after 1 second of continuous segments turn ON and OFF properly. q Push [MENU] to enter the Menu mode. w Push [∫] or [√] to select "Diagnostics," then push [ENT]. e
  • Icom MA-500TR | Instruction Manual - Page 53
    properly. q Push [MENU] to enter the Menu mode. w Push [∫] or [√] to select "Diagnostics," then push [ENT]. e Push [∫] or [√] to select "Transponder Test," then push [ENT]. r The screen shows the results of the ROM, RAM, RX/TX unit, antenna and GPS receiver tests; "OK" or "NG" (No Good). t Push
  • Icom MA-500TR | Instruction Manual - Page 54
    GMSK : Less than -36 dBm D Receiver • Sensitivity (20% Packet Error Rate dB • Conducted spurious emission : Less than -57 dBm (AIS) This equipment meets IEC 62287-1 specifications. 46 D Dimensions 145 notice or obligation. ■ Option • MB-75 flush mount kit Used to mount the transponder to a panel.
  • Icom MA-500TR | Instruction Manual - Page 55
    Cut here 92.4 (3 5⁄8) 110 (4 11⁄32) R12 (Max.) 165 (6 1⁄2) 146 (5 3⁄4) 10 TEMPLATE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Unit: mm (inch) 47
  • Icom MA-500TR | Instruction Manual - Page 56
  • Icom MA-500TR | Instruction Manual - Page 57
    11 AtoN CODE AND DESCRIPTION The following table shows all the AtoN codes which appear on the detail screens of an "AtoN." (p. 21) Code Description 0 DEFAULT, TYPE OF ATON NOT SPECIFIED 1 REFERENCE POINT 2 RACON 3 OFF SHORE STRUCTURE 4 SPARE 5 LIGHT, WITHOUT SECTORS 6 LIGHT, WITH SECTORS
  • Icom MA-500TR | Instruction Manual - Page 58
    MEMO
  • Icom MA-500TR | Instruction Manual - Page 59
    MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
  • Icom MA-500TR | Instruction Manual - Page 60
    < Intended Country of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR A-6860D-1EX-q Printed in Japan © 2011 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
INSTRUCTION MANUAL
MA-500TR
CLASS B AIS TRANSPONDER
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition that
this device does not cause harmful interference.