Intel D2700MUD Technical Product Specification for Intel Desktop Board D2700MU - Page 40

Connectors and Headers

Get Intel D2700MUD PDF manuals and user guides View all Intel D2700MUD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Intel Desktop Board D2700MUD Technical Product Specification 2.2 Connectors and Headers CAUTION Only the following connectors/headers have overcurrent protection: Back panel and front panel USB, VGA, serial, and PS/2. The other internal connectors/headers are not overcurrent protected and should connect only to devices inside the computer's chassis, such as fans and internal peripherals. Do not use these connectors/headers to power devices external to the computer's chassis. A fault in the load presented by the external devices could cause damage to the computer, the power cable, and the external devices themselves. NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. This section describes the board's connectors and headers. The connectors and headers can be divided into these groups: • Back panel I/O connectors (see page 41) • Component-side connectors and headers (see page 43) 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Intel Desktop Board D2700MUD Technical Product Specification
40
2.2
Connectors and Headers
CAUTION
Only the following connectors/headers have overcurrent protection:
Back panel and
front panel USB, VGA, serial, and PS/2.
The other internal connectors/headers are not overcurrent protected and should
connect only to devices inside the computer’s chassis, such as fans and internal
peripherals.
Do not use these connectors/headers to power devices external to the
computer’s chassis.
A fault in the load presented by the external devices could cause
damage to the computer, the power cable, and the external devices themselves.
NOTE
Computer systems that have an unshielded cable attached to a USB port may not meet
FCC Class B requirements, even if no device is attached to the cable.
Use shielded
cable that meets the requirements for full-speed devices.
This section describes the board’s connectors and headers.
The connectors and
headers can be divided into these groups:
•
Back panel I/O connectors (see page 41)
•
Component-side connectors and headers (see page 43)