JVC DLA-DS1U Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project
JVC DLA-DS1U - General Purpose D-ila Projector Manual
View all JVC DLA-DS1U manuals
Add to My Manuals
Save this manual to your list of manuals |
JVC DLA-DS1U manual content summary:
- JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 1
D-ILATM PROJECTOR series series RS-232C CONTROL SPECIFICATIONS Victor Company of Japan, Limited * D-ILA is a trademark of Victor Company of Japan, Limited. Document Number CTGKE-0013 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 2
CONTENTS 1. Outline ...2 2. Communication Format 2 3. Data Format ...2 4. Header ...4 5. ID ...4 6. CR ...5 7. Parameters...5 8. Tally (Response) Data 9 9. Internal Errors ...10 10 Projector Operation Modes 12 11. Source ...13 12. Commands ...14 13. Appendix ...55 1 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 3
Parity Bit : Start Bit : Flow Control : 9600, 19200(default) bps 8 bits None 1 bit None 3.DATA FORMAT 3.1 Command Data Format (External Control to Projector) Header ID SP Command SP Parameter SP Parameter SP ・・ CR Header : Indicates the beginning of data and data type '!'(21H) : Command for - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 4
when Error Occurs Header ID SP Error Status CR Header : Indicates the beginning of the tally (response) data '@'(40H) ID : Identification number of Projector SP : Indicates the separation between ID and Status(20H) Error Status : 'A00' (41H 30H 30H) 'A01' (41H 30H 31H) 'A02' (41H 30H 32H - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 5
(41H) 'B' (42H) 'C' (43H) 'D' (44H) 'E' (45H) 'F' (46H) * Factory set ID is '1' (31H). ID number '0' (30H) should be used when assigning all connected Projector units for batch operations. This means that when assigning independent ID numbers to multiple units, 15 of the 16 assignable numbers (from - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 6
6. CR Indicates the end of each set of data. (0DH) 7. PARAMETERS There are three types of parameters: 1.Indicates the numeric value. 2.Indicates the ON/OFF status. 3.Special parameter. 7.1 Numeric Value Parameter Signed 2-byte hexadecimal code represented by 4 (byte) characters. Assignable range - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 7
7.3 Special Parameters Parameters other than those described in 7.1 to 7.2. 7.3.1 Menu Display Auto OFF Parameter Character HEX Definition '0' 30 NO '1' 31 YES 7.3.2 Transfer Rate Parameter Character HEX '0' 30 '1' 31 Definition 9600bps 19200bps 7.3.3 Decoder Parameter Character HEX - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 8
7.3.6 Projector Operation Mode Parameter Character HEX '0000' 30H 30H 30H 30H '0001' 30H 30H 30H 31H '0002' 30H 30H 30H 32H '0004' 30H 30H 30H 34H - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 9
HEX '0' 30 '1' 31 '2' 32 '3' 33 '4' 34 '5' 35 '6' 36 '7' 37 '8' 38 '9' 39 'A' 41 'B' 42 'C' 43 'D' 44 'E' 45 'F' 46 Definition ID 0(global command for all projectors) ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9 ID 10 ID 11 ID 12 ID 13 ID 14 ID 15 7.3.11 Switcher - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 10
with the ID-number registered to the Projector itself. (Except when ID = '0') If the received ID-number matches the Projector's ID, it will return a response Status) Character HEX Definition 'A00' 41H 30H 30H Command not supported 'A01' 41H 30H 31H Invalid parameter 'A02' 41H 30H 32H - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 11
9. INTERNAL ERRORS Error data is returned to the external control unit when an error has occurred. 9.1 Internal Error Data Status (Internal Error Status) Character HEX Definition 'E01' 45H 30H 31H Lamp did not light 'E02' 45H 30H 32H Lamp life exceeds guaranteed time 'E03' 45H 30H 33H IIC - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 12
data exists, the internal error data is returned before the tally (response) data is transmitted. That is, if an internal error occurs, the Projector retains the internal error data, returning it in order of precedence a request for tally (response) data is received. Once transmitted, internal error - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 13
is turned OFF. Non-operation status continues until the reset function is activated. Switch ON the projector's MAIN POWER After 90 sec. Lamp cool-down (DLA-G3010 Series) After 120 sec. Lamp cool-down (DLA-M2000 Series) Cool Down Mode Filter cover Fan lock Standby Mode POWER OFF Sleep Time Lamp - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 14
11. SOURCE The input signals to projectors can be Computer Sources and Video Sources. Although the specific signal names are not given to Computer Sources , ※ Note that the acceptance / non-acceptance of a command is differ depending on the Source (Area) actually registered on the Projector. 13 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 15
as '1' (31H). This is the default setting. ◇ "CTLR" refers to transmissions from the external control unit and "DLA" refers to transmissions (Tally (Response) Data) from the Projector. ◇ "Reply Time" refers to the maximum time required between command reception and return of Tally (Response) Data - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 16
'(55H 30H 30H) :ON/OFF :3seconds : Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ To turn HIDE ON CTLR DLA '!' '1' SP 'U00' SP '1' CR '@' '1' SP '0' CR ◇ When requesting current HIDE status (if HIDE status is ON) CTLR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 17
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "30" (decimal) as the horizontal position CTLR DLA '!' '1' SP 'U02' SP '001E' CR '@' '1' SP '0' CR ◇ When requesting current horizontal position data (if horizontal position is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 18
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "5" (decimal) as the vertical position CTLR DLA '!' '1' SP 'U03' SP '0005' CR '@' '1' SP '0' CR ◇ When requesting current vertical position data (if vertical position is set to "16 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 19
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "50" (decimal) as the phase adjust level CTLR DLA '!' '1' SP 'U04' SP '0032' CR '@' '1' SP '0' CR ◇ When requesting the current phase adjust level (if phase adjust level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 20
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "50" (decimal) as tracking adjust level CTLR DLA '!' '1' SP 'U05' SP '0032' CR '@' '1' SP '0' CR ◇ When requesting current tracking adjust level data (if tracking adjust level is set - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 21
mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "2" (decimal) as the contrast adjust level CTLR DLA '!' '1' SP 'U06' SP '0002' CR '@' '1' SP '0' CR ◇ When requesting current contrast adjust level data (if contrast adjust level is set - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 22
mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "-2" (decimal) as the brightness adjust level CTLR DLA '!' '1' SP 'U07' SP 'FFFE' CR '@' '1' SP '0' CR ◇ When requesting current brightness adjust level data (if brightness adjust level is set - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 23
mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "2" (decimal) as the sharpness CTLR DLA '!' '1' SP 'U08' SP '0002' CR '@' '1' SP '0' CR ◇ When requesting current sharpness adjust level data (if sharpness adjust level is set - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 24
mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "-2" (decimal) as the color adjust level CTLR DLA '!' '1' SP 'U09' SP 'FFFE' CR '@' '1' SP '0' CR ◇ When requesting current color adjust level (if color adjust level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 25
mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "-2" (decimal) as the tint adjust level CTLR DLA '!' '1' SP 'U0A' SP 'FFFE' CR '@' '1' SP '0' CR ◇ When requesting current tint adjust level data (if tint adjust level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 26
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "MIDDLE" as the color temperature CTLR DLA '!' '1' SP 'U0B' SP '1' CR '@' '1' SP '0' CR ◇ When requesting current color temperature data (if color temperature is set to "LOW") CTLR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 27
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "-2" (decimal) as the R-gain adjust level CTLR DLA '!' '1' SP 'U0C' SP 'FFFE' CR '@' '1' SP '0' CR ◇ When requesting current R-gain adjust level data (if R-gain adjust level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 28
Standby mode Power ON mode Cool-down mode X O X Emergency mode X # Communication Examples ◇ When specifying "-2" (decimal) as the G-gain adjust level CTLR DLA '!' '1' SP 'U0D' SP 'FFFE' CR '@' '1' SP '0' CR ◇ When requesting current G-gain adjust level data (if G-gain adjust level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 29
Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "-2" (decimal) as the B-gain adjust level CTLR DLA '!' '1' SP 'U0E' SP 'FFFE' CR '@' '1' SP '0' CR ◇ When requesting current B-gain adjust level data (if B-gain adjust level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 30
POWER OFF command is received during Power-ON mode, the Projector enters the cool-down mode (DLA-G3010 series: for about 90 seconds, DLA-M2000L series: for about 120 seconds) and continue cooling (DLA-G20series: for about 120 seconds, DLA-M4000L series: for about 10 minutes). After cool-down mode - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 31
Power ON mode Cool-down mode Emergency mode O O O X # Communication Examples ◇ When specifying that the menu display is turned off automatically CTLR DLA '!' '1' SP 'U10' SP '1' CR '@' '1' SP '0' CR ◇ When requesting the current menu display auto-off setting (if menu display does not turn - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 32
: Operation mode Standby mode Power ON mode Cool-down mode Emergency mode O O O X # Communication Examples ◇ When setting the line display to OFF CTLR DLA '!' '1' SP 'U11' SP '0' CR '@' '1' SP '0' CR ◇ When requesting the current line display setting (if the line display is set to ON) CTLR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 33
O O O X The "Sleep time" function automatically turns off the projector power if the no-signal status continues for a specified time. *Available numeric. # Communication Examples ◇ When specifying "30 min." as the sleep time CTLR DLA '!' '1' SP 'U12' SP '001E' CR '@' '1' SP '0' CR ◇ When - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 34
mode Power ON mode Cool-down mode Emergency mode O O O X # Communication Examples ◇ When reversing the image horizontally (Right /Left reverse) CTLR DLA '!' '1' SP 'U17' SP '1' CR '@' '1' SP '0' CR ◇ When requesting the current R/L reverse setting (if the image is not reversed horizontally - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 35
Standby mode Power ON mode Cool-down mode Emergency mode O O O X # Communication Examples ◇ When inverting the image vertically (Top/Bottom invert) CTLR DLA '!' '1' SP 'U18' SP '1' CR '@' '1' SP '0' CR ◇ When requesting the current Top/Bottom invert setting (if the image is not inverted - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 36
mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When selecting "NTSC" as the broadcast system CTLR DLA '!' '1' SP 'U19' SP '0' CR '@' '1' SP '0' CR ◇ When requesting the current broadcast system setting (if the broadcast system is set to PAL - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 37
Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When selecting "D-SUB" as the video input CTLR DLA '!' '1' SP 'U1A' SP '3' CR '@' '1' SP '0' CR ◇ When requesting the current video input setting (if the video input is selected) CTLR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 38
at the new transfer rate. # Communication Examples ◇ When changing the transfer rate to "9600 bps" from the current setting of "19200 bps" CTLR DLA '!' '1' SP 'U1B' SP '0' CR '@' '1' SP '0' CR "19200bps" until this point "9600bps" from here on * The default transfer rate setting is "19200bps - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 39
new one. △ Tally (Response) data format when requesting current time '@' '1' SP Normal Termination Status SP Parameter 1 SP Parameter 2 CR (*)Parameter1 The Projector has an incremental counter which counts Lamp Operation Time at 1 time in every 4 minutes. Parameter 1 shows this counter value. The - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 40
operating time < Lamp service life Lamp replacement time not close Lamp replacement time close Lamp life exceeded Character '0' '1' '2' HEX 30H 31H 32H # Communication Examples ◇ When requesting the current lamp operating time (if the lamp operating time is 150 hours) CTLR DLA '?' '1' SP 'U1C - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 41
:'U1D'(55H 31H 44H) Definition :Sets the ID for the Projector Command Parameter type Reply time Conditions :'U1D'(55H 31H 44H) Communication Examples ◇ When changing the ID to '7' from the current setting of '1' CTLR DLA '!' '1' SP 'U1D' SP '7' CR '@' '7' SP '0' CR Tally (Response) data is returned - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 42
mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Example ◇ When setting the volume adjust level to "30" CTLR DLA '!' '1' SP 'U20' SP '001E' CR '@' '1' SP '0' CR ◇ When requesting the current volume adjust level setting (if the volume level is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 43
ON/OFF. ◇ Quick alignment parameter Character HEX OFF '0' 30H The Projector performs quick alignment processing after returning Normal Termination Status Tally (Response) data sec Possible to transmit next command CTLR '!' '1' SP 'U2A' SP '0' CR DLA '@' '1' SP '0' CR '?' '1' SP 'Z03' CR 42 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 44
) Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When setting the text mode to "Normal" CTLR DLA '!' '1' SP 'U2C' SP '0' CR '@' '1' SP '0' CR ◇ When requesting current text mode setting (if the text mode is set to "Text 1") CTLR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 45
) Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When setting the resize function to 1:1 CTLR DLA '!' '1' SP 'U2D' SP '0' CR '@' '1' SP '0' CR ◇ When requesting the current resize function setting (if the resize function is set to - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 46
) Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When setting the aspect ratio to "4:3" CTLR DLA '!' '1' SP 'U2E' SP '0' CR '@' '1' SP '0' CR ◇ When requesting the current aspect ratio setting(if the aspect ratio is set to "16 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 47
Examples ◇ When requesting horizontal frequency (if horizontal frequency is 64.3kHz) CTLR DLA '?' '1' SP 'U3C' CR '@' '1' SP '0' SP '0283' CR Note) Horizontal Frequency is 10 times of data to be returned from Projector. This example shows 283 in hexadecimal, which is 643 in decimal. Horizontal - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 48
) signal Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When requesting vertical frequency (if vertical frequency is 60Hz) CTLR DLA '?' '1' SP 'U3D' CR '@' '1' SP '0' SP '003C' CR 47 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 49
) signal Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When requesting horizontal resolution (if horizontal resolution is 1280) CTLR DLA '?' '1' SP 'U3E' CR '@' '1' SP '0' SP '0500' CR 48 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 50
) signal Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When requesting vertical resolution (if vertical resolution is 1024) CTLR DLA '?' '1' SP 'U3F' CR '@' '1' SP '0' SP '0400' CR 49 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 51
: Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Examples ◇ When specifying "0" (decimal) as keystone CTLR DLA '!' '1' SP 'U40' SP '0080' CR '@' '1' SP '0' CR ◇ When requesting the keystone (if the keystone is set to "0" (decimal)) CTLR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 52
O When the POWER OFF command is received in the Power ON mode, the Projector first enters the Cool-Down mode, then automatically enters the Standby mode. (For information requesting the current operation mode(if the Projector is in the standby mode) CTLR DLA '?' '1' SP 'Z03' CR '@' '1' SP '0' SP '0000' CR - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 53
Operation mode Standby mode Power ON mode Cool-down mode Emergency mode X O X X # Communication Example ◇ When requesting the current Source (Area) setting actually assigned on the Projector (if Computer Sources is actually assigned) CTLR DLA '?' '1' SP 'Z05' CR '@' '1' SP '0' SP 'F0' CR 52 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 54
HEX 44H 30H 33H 2DH 2DH 2DH 2DH 4DH 32H 30H 30H 30H 2DH 2DH Definition DLA-G3010 Series Projector DLA-M2000 Series Projector # Communication Example ◇ When the projector is a M2000 series projector with software version 1.2.1 CTLR DLA '?' '1' SP 'Z0A' CR '@' '1' SP '0' SP 'M2000--00121' CR 53 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 55
according to commands from the Switcher. When Projector receive the command, Projector switches input terminal to RGB. And Source to Examples ◇ When specifying Switcher 2 (if a channel specifying input switcher 2 exists.) CTLR DLA '!' '1' SP 'W00' SP '0002' CR '@' '1' SP '0' CR ◇ When - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 56
13. APPENDIX 13. 1 External Control Command List Command Hide Horizontal Position Vertical Position Phase Tracking Contrast Brightness Sharpness Color Tint Color Temperature R-Gain G-Gain B-Gain Power Menu Auto Off Line Display Sleep Time Right/Left Reverse Top/Bottom Invert Decoder Input Select - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 57
Volume Quick Alignment Text Mode Resize Aspect Change Horizontal Frequency Query Vertical Frequency Query Horizontal Resolution Query Vertical Resolution Query Keystone Operation Mode Query Source Query Model Status Switcher Selection 'U20' 'U2A' 'U2C' 'U2D' 'U2E' 'U3C' 'U3D' 'U3E' 'U3F' 'U40' 'Z03 - JVC DLA-DS1U | Serial protocol for the DLA-DS1U and DLA-M2000LU/SC D-ILA project - Page 58
13. 2 RS-232C Port Pin Configuration RS-232C Control Port D-SUB 9-pin (Male) Pin No. Signal 1 N/A 2 RxD(RD) 3 TxD(SD) 4 N/A 5 GND 6 N/A 7 N/A 8 N/A 9 N/A Definition Not used Receive data Transmit data Not used GND Not used Not used Not used Not used 57
D-ILA
PROJECTOR
DLA-G3010
DLA-G3010
DLA-G3010
DLA-G3010
series
series
series
series
DLA-M2000
DLA-M2000
DLA-M2000
DLA-M2000
series
series
series
series
RS-232C CONTROL SPECIFICATIONS
Victor Company of Japan, Limited
* D-ILA is a trademark of Victor Company of Japan, Limited.
Document Number
CTGKE-0013
TM