JVC GY-DV300U KA-DV300U/Streamproducer Quick Start Guide. - Page 1

KA-DV300U / Streamproducer Quick-Start For KA-DV300 firmware version 104 and Streamproducer 2.0 JVC wants you to get the most out of your GYDV300 with the KA-DV300 Network Pack. If you have any questions, concerns or problems, please feel free to contact our Network Product Specialist at: [email protected] Supported Accessory Cards: • Operating Voltage: 3.3 VDC • Max. Current: 300 mA @ 5V As of October 2002, the KA-DV300 supports the following accessory cards: • Wired LAN: o Socket Communications (www.socketcom.com) US: EA2900-117 (Rev. C)1 Europe: EA2903-162 (Rev. C)1 Asia: EA2906-194 (Rev. C)1 revision number on the upper-right of the product label. • Wireless LAN: o TRENDNet (www.trendware.com) TEW-16PC, revision 0.8.3 or later (discontinued) TEW-201PC o Linksys (www.linksys.com) WCF112 • CF Memory: o SanDisk (www.sandisk.com) SDCFB-16 ~ SDCFB-2561 1 - requires CF type I or type II to PCMCIA adapter 2 - requires CF Type II to PCMCIA adapter Attaching the KA-DV300 to the GYDV300 1. Insure that the GY-DV300 power is off. 2. Slide the connector cover located on the bottom of the GYDV300 in the direction as shown by the arrow located next to the connector cover. 3. Align the hook on the KA-DV300 with the cutout on the rear of the GY-DV300 below the battery compartment. Hook 4. Rotate the KA-DV300 upward toward the GY-DV300 until a positive 'click' is heard and felt. 5. To remove the KA-DV300 Network Pack, press the release button on the front of the pack and pull away from the camera. Release button Inserting Accessory Card 1. Insure that the GY-DV300 power is OFF. 2. Insert the accessory card in the KA-DV300. The card can only be inserted in one direction. Do not force the card into the slot. 3. Turn on the power to the GY-DV300. 4. The status of the inserted card is displayed on the LCD and/or viewfinder screen. NOTES: • When turning the power on, the card status display will flash during initialization. • Inserting a card with the power ON may result in damage to the card. Wired Connections, Single Camera to Single Computer DHCP: OFF IP Address: 192.168.100.101 Netmask: 255.255.255.0 DHCP: OFF IP Address: 192.168.100.102 Netmask: 255.255.255.0 Both IP addresses must be within the same network group and have the same subnet mask, as shown by the shading above. In this example, the Network Group is 192.168.100. When connecting directly from the camera to a computer, operation is assured if the following conditions are met: • DHCP should be OFF. • If DHCP is off, the IP address of the camera and the computer must be unique, but in the same Network Group. • The Netmask of both the camera and computer must be the same. • A CAT-5 crossover cable is used between the camera and computer if no switch or hub is present. • Under most conditions, the computer LAN card should be set for no proxy server. Please refer to the KA-DV300 Users Guide for information regarding this setting if troubles are encountered. Wireless Connections, Single Camera to Single Computer In a similar manner to the wired connection, when connecting directly from the camera to a computer using a wireless link without an access point, operation is assured if the following conditions are met: • DHCP must be OFF. • The IP address of the camera and the computer must be unique, but in the same Network Group. • The Netmask of both the camera and computer must be the same • set the WLAN AD HOC MODE to ON. • The WLAN ESS ID on both the KA-DV300 and the computer must be the same. The camera default ESS ID is 'wireless-lan'. • The KA-DV300 and the computer must be set to use the same channel (WLAN CH). • Under most conditions, the computer LAN card should be set for no proxy server. Please refer to the KA-DV300 Users Guide 'Setting a Proxy Server' for information regarding this setting if troubles are encountered.