Kenwood CAX-AD100 Operation Manual - Page 4

Battery Replacement and Sensor When the battery runs out When the battery runs out, and the red LED will blink simultaneously. If you see this, replace the batteries. [Please use AA alkaline batteries] (Do not use manganese batteries or rechargeable batteries) When replacing the batteries, allow 20 seconds with the batteries removed, and then insert the new batteries. symbol will be reset and disappear. About the "SENSOR EXCHANGE" indicator When you use this product more than 5,000 times, the "SENSOR EXCHANGE" mark blinks. Since the measurement accuracy of the sensor will not be maintained, it is recommended to replace this product. • Even if it is used infrequently, it is recommended to replace it with a new one after using it for one year. # CAUTION • Risk of fire or explosion if the battery is replaced by an incorrect type. Ensure to replace only with the same type. • Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is left in an extermely high temperature surrounding environment and/or subjected extremely low air pressure. The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like. • Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is disposed into fire or a hot oven, recharged, shorted, mechanically crushed or cut of the battery. • If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water and consult a physician. Declaration of Conformity with regard to the EMC Directive 2014/30/EU Declaration of Conformity with regard to the RoHS Directive 2011/65/EU Manufacturer: JVCKENWOOD Corporation 3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, JAPAN EU Representative: JVCKENWOOD Europe B.V. Amsterdamseweg 37, 1422 AC Uithoorn, THE NETHERLANDS Product Specifications Power supply DC 3 V two AA alkaline batteries Battery life About 1,200 times Operating temperature 0 °C to 35 °C (no condensation) Storage temperature -10 °C to 60 °C (no condensation) External dimensions 122 x 45 x 21 mm Mass / Weight Approximately 92 g (including batteries) Main materials Body case: ABS resin Detection method Semiconductor gas sensor Display method LCD digital display 0.00 mg/L and 0.05 mg/L to 1.00 mg/L (If less than 0.05 mg/L, 0.00 mg/L will be displayed) LED 2-stage display (Green/Red) Sensor life Purchased and used 1 year or 5,000 times Accessories Instruction manual (warranty), attachment, strap, Two AA alkaline batteries * The contents and specifications are subject to change without notice. Declaration of Conformity with regard to the Electromagnetic Compatibility Regulations 2016 (S.I. 2016/1091) Declaration of Conformity with regard to the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (S.I. 2012/3032) Manufacturer: JVCKENWOOD Corporation 3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, JAPAN UK Importer: JVCKENWOOD U.K. Limited 12 Priestley Way, London, NW2 7BA, UNITED KINGDOM Troubleshooting Cannot turn on Are there batteries? † Set two AA alkaline batteries (included) correctly. Is the plus/minus of the battery set in reverse? † Please set plus and minus correctly. Error display "---" Are you blowing properly? Is there any odor or gas at the measurement location? † Please refer to "How to use" in this manual and measure correctly. The measured value is Are you using it in a windy place or a place with a strong not stable. odor? † Please change the location and measure. Getting an alcohol Is there any odor remain inside the product? reaction even though † Shake this product lightly 2-3 times. not drinking. Are you measuring immediately after using mouthwash or smoking ? † Please refer to "Understanding Breath Alcohol Tester" in this manual . No alcohol reaction The blown breath may not have passed through the even though drinking. sensor part. † Refer to step 4 of "How to use" in this manual, and blow properly.