KitchenAid KBBL206EPA Installation Guide - Page 22

Door Swing Adjustment, 91.4 cm Single-Door Models, 106.7 cm Models

Get KitchenAid KBBL206EPA PDF manuals and user guides View all KitchenAid KBBL206EPA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Door Swing Adjustment 4. The door stop is located on the top hinge. 36" (91.4 cm) Single-Door Models 1. Check that the refrigerator door can open freely. If the door opens too wide, remove the door stop screw from the bottom hinge with a Torx®† T15 screwdriver. A B C A A. Door stop screw 2. Hold the door open to a position that is less than 90°. 3. Replace the door stop screw in the bottom hinge and tighten. IMPORTANT: Do not place the door stop screw in the 130° position on Overlay Series models. See "Handle and Door Clearances." A. Door stop screw "A" B. Door stop screw "B" C. Door stop 5. Remove the two door stop screws. ■ To remove the outer screw ("A"): With the door closed, firmly press the L-shaped bracket toward the center of the refrigerator until the screw is exposed. ■ To remove the inner screw ("B"): Open the door 90° and the L-shaped bracket will expose the screw. A AB C A. 130° C. 90° B. 110° (Overlay series) B 42" (106.7 cm) Models 1. Check that the refrigerator door can open freely. If the door opens too wide, you will have to adjust the door stop position. 2. Grasp both ends of the top grille. 3. Push the top grille straight up, then pull straight out. Lay the grille on a soft surface. B A B A. Door stop screw "A" B. Door stop screw "B" A. Top grille B. Cabinet side trims 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
22
Door Swing Adjustment
36" (91.4 cm) Single-Door Models
1.
Check that the refrigerator door can open freely. If the door
opens too wide, remove the door stop screw from the bottom
hinge with a Torx
®†
T15 screwdriver.
2.
Hold the door open to a position that is less than 90°.
3.
Replace the door stop screw in the bottom hinge and tighten.
IMPORTANT:
Do not place the door stop screw in the 130°
position on Overlay Series models. See “Handle and Door
Clearances.”
42" (106.7 cm) Models
1.
Check that the refrigerator door can open freely. If the door
opens too wide, you will have to adjust the door stop position.
2.
Grasp both ends of the top grille.
3.
Push the top grille straight up, then pull straight out. Lay the
grille on a soft surface.
4.
The door stop is located on the top hinge.
5.
Remove the two door stop screws.
■
To remove the outer screw (“A”):
With the door closed, firmly press the L-shaped bracket
toward the center of the refrigerator until the screw is
exposed.
■
To remove the inner screw (“B”):
Open the door 90° and the L-shaped bracket will expose
the screw.
A. Door stop screw
A. 130°
B. 110° (Overlay series)
C. 90°
A. Top grille
B. Cabinet side trims
A
A
B
C
B
B
A
A. Door stop screw “A”
B. Door stop screw “B”
C. Door stop
A. Door stop screw “A”
B. Door stop screw “B”
B
A
C
A
B