KitchenAid KBF042FTX Installation Guide - Page 27

Install Side Panel

Get KitchenAid KBF042FTX - 22.5CF FR Dr 42inch W K/A PDF manuals and user guides View all KitchenAid KBF042FTX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

5. Remove the 2 door stop screws. ■ To remove the outer screw ("A"): With the door closed, firmly press the L-shaped bracket toward the center of the refrigerator until the screw is exposed. ■ To remove the inner screw ("B"): Open the door 90° and the L-shaped bracket will expose the screw. A Install Side Panel If the built-in area depth is 25" (63.5 cm) or more, the side panels can be installed inside the side trim or attached to the outside of the side trim. IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service. 1. For the inside side trim piece, slide the front edge of the routed side panel into the trim piece. 2. Nail the rear edge of the panel to the support board. A B A. Door stop screw "A" B. Door stop screw "B" 6. Reverse or rotate the door stop to the desired position as shown below. NOTE: For Overlay Series models, rout the hinge side of the custom door panels to a radius that is equal to at least half the thickness of the panel if a 130° door swing is desired. 130° 110° B A. Support board B. Side trim piece 90° 90° Left-hand as shown; Right-hand reversed 7. Replace the door stop screws and tighten. 8. Check that the door can open freely. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
27
5.
Remove the 2 door stop screws.
■
To remove the outer screw (“A”):
With the door closed, firmly press the L-shaped bracket
toward the center of the refrigerator until the screw is
exposed.
■
To remove the inner screw (“B”):
Open the door 90° and the L-shaped bracket will expose
the screw.
6.
Reverse or rotate the door stop to the desired position as
shown below.
NOTE:
For Overlay Series models, rout the hinge side of the
custom door panels to a radius that is equal to at least half the
thickness of the panel if a 130° door swing is desired.
7.
Replace the door stop screws and tighten.
8.
Check that the door can open freely.
Install Side Panel
If the built-in area depth is 25" (63.5 cm) or more, the side panels
can be installed inside the side trim or attached to the outside of
the side trim.
IMPORTANT:
KitchenAid is not responsible for the removal or
addition of molding or decorative panels that would not allow
access to the refrigerator for service.
1.
For the inside side trim piece, slide the front edge of the
routed side panel into the trim piece.
2.
Nail the rear edge of the panel to the support board.
A. Door stop screw “A”
B. Door stop screw “B”
130°
110°
90°
90°
Left-hand as shown; Right-hand reversed
A
B
A. Support board
B. Side trim piece
A
B