KitchenAid KBFS20ETBL Use and Care Guide - Page 7

KitchenAid KBFS20ETBL - 19.7 cu. ft. 35 5/8 in. Width ArchitectR Series IIBl Manual

Get KitchenAid KBFS20ETBL - 19.7 cu. ft. 35 5/8 in. Width ArchitectR Series IIBl PDF manuals and user guides View all KitchenAid KBFS20ETBL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

5. Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten. Replace the Base Grille 1. See the markings on the inside of the base grille for proper placement. 2. Align the grille mounting clips with the cabinet slots. 3. Push the grille firmly into the cabinet slots until it snaps into place. A B C D E A. Plastic water line B. Water valve inlet port C. Compression nut D. Copper tubing E. "P" clamp 6. Check connection by pulling on copper tubing. Attach copper tubing to refrigerator cabinet with a "P" clamp. Turn on water supply to refrigerator and check for leaks. Correct any leaks. Refrigerator Doors Graphics are included later in this section. Complete the Installation Remove and Replace Handles 1. Using a Allen wrench, loosen the two set screws located on the side of each handle. See Graphics 1 and 2. 2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching the handles. 3. To replace the handles, reverse the directions. WARNING Remove Doors and Hinges Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Plug into a grounded 3 prong outlet. NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice container. WARNING Electrical Shock Hazard Disconnect power before removing doors. Failure to do so can result in death or electrical shock. IMPORTANT:

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
7
5.
Using an adjustable wrench, hold the nut on the plastic water
line to keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise
to completely tighten. Do not overtighten.
6.
Check connection by pulling on copper tubing. Attach copper
tubing to refrigerator cabinet with a “P” clamp. Turn on water
supply to refrigerator and check for leaks. Correct any leaks.
Complete the Installation
1.
Plug into a grounded 3 prong outlet.
NOTE:
Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to
completely fill the ice container.
Base Grille
Remove the Base Grille
1.
Grasp the grille with both hands.
2.
Pull the grille toward you.
Replace the Base Grille
1.
See the markings on the inside of the base grille for proper
placement.
2.
Align the grille mounting clips with the cabinet slots.
3.
Push the grille firmly into the cabinet slots until it snaps into
place.
Refrigerator Doors
Graphics are included later in this section.
Remove and Replace Handles
1.
Using a
³/₃₂
" Allen wrench, loosen the two set screws located
on the side of each handle. See Graphics 1 and 2.
2.
Pull the handle straight out from the door. Make sure you
keep the screws for reattaching the handles.
3.
To replace the handles, reverse the directions.
Remove Doors and Hinges
IMPORTANT:
■
Remove food and any adjustable door or utility bins from
doors.
■
All graphics referenced in the following instructions are
included later in this section after “Final Steps.”
TOOLS NEEDED:
⁵/₁₆
",
³/₈
",
¹/₄
" hex-head socket wrench,
#2 Phillips screwdriver, and a flat-blade screwdriver.
A. Plastic water line
B. Water valve inlet port
C. Compression nut
D. Copper tubing
E. “P” clamp
B
A
C
D
E
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.