KitchenAid KBSD608EBS Use & Care Guide - Page 18
Performance Data Sheets
View all KitchenAid KBSD608EBS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
PERFORMANCE DATA SHEETS Base Grille Water Filtration System Model T2WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters) Model T2WG2/T2RFWG2 Capacity 200 Gallons (757 Liters) System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran. This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53. Substance Reduction Aesthetic Effects Chlorine Taste/Odor Particulate Class II* Contaminant Reduction Lead: @ pH 6.5*** Lead: @ pH 8.5*** Mercury: @ pH 6.5 Mercury: @ pH 8.5 Benzene O-Dichlorobenzene Toxaphene Carbofuran NSF Reduction Requirements 50% reduction 85% reduction NSF Reduction Requirements 0.010 mg/L 0.010 mg/L 0.002 mg/L 0.002 mg/L 0.005 mg/L 0.6 mg/L 0.003 mg/L 0.04 mg/L Average Influent Influent Challenge Concentration Maximum Effluent 2.0182 mg/L 2.0 mg/L ± 10% 0.06 mg/L 1333333 #/mL At least 10,000 particles/mL 6600 #/mL** Average Influent Influent Challenge Concentration Maximum Effluent 0.1533 mg/L 0.15 mg/L ± 10% 0.1400 mg/L 0.15 mg/L ± 10% 0.0005 mg/L 0.0007 mg/L 0.0058 mg/L 0.006 mg/L ± 10% 0.0059 mg/L 0.006 mg/L ± 10% 0.0002 mg/L 0.0005 mg/L 0.0154 mg/L 0.015 mg/L ± 10% 0.0012 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.015 mg/L 0.015 mg/L ± 10% 0.001 mg/L 0.0819 mg/L 0.08 mg/L ± 10% 0.0400 mg/L Average Effluent 0.0536 mg/L 2325 #/mL Average Effluent 0.0005 mg/L 0.0006 mg/L 0.0002 mg/L 0.0003 mg/L 0.0006 mg/L 0.0066 mg/L 0.001 mg/L 0.0213 mg/L Minimum % Reduction 97.03 99.51 Minimum % Reduction 99.67 99.50 96.54 91.57 92.22 98.58 93.33 51.13 Average % Reduction 97.34 99.83 Average % Reduction 99.67 99.57 96.54 94.92 96.34 99.63 93.33 74.00 Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters). It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Use replacement filter T2RFWG2, part #4396841. Model T2WG2L: Style 1 - When the filter indicator reads 10%, order a new filter. When the indicator reads 0%, it is recommended that you replace the filter. Refer to the "Warranty" section for the Manufacturer's name, address and telephone number. Refer to the "Warranty" section for the Manufacturer's limited warranty. Style 2 - When the filter indicator changes from green to yellow, order a new filter. When the indicator changes from yellow to red, it is recommended that you replace the filter. Style 3 - When the water filter status display changes from "GOOD" to "ORDER," order a new filter. When the filter indicator reads "REPLACE," it is recommended that you replace the filter. Style 4 - Press FILTER to check the status of your water filter. If the filter indicator light is yellow, order a new filter. If the filter indicator light is red, it is recommended that you replace the filter. Application Guidelines/Water Supply Parameters Water Supply Water Pressure Water Temperature Service Flow Rate City or Well 30 - 120 psi (207 - 827 kPa) 33° - 100°F (0.6° - 37.8°C) 0.85 gpm (3.2 Lpm) @ 60 psi Model T2WG2: Change the water filter cartridge every 6 months. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter cartridge more often. These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary. The product is for cold water use only. *Class II particle size: 1 um to