KitchenAid KGRS807SBL Installation Instructions - Page 17
To Convert Standard Surface Burners, To Convert TripleTier, Flame Burners on some models - rating
UPC - 883049027371
View all KitchenAid KGRS807SBL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
6. Turn the gas pressure regulator cap over and reinstall on regulator so that the hollow end faces out and letters "LP" are visible. 7. Replace plastic cover over gas pressure regulator cap. To Convert Standard Surface Burners 1. Remove burner cap. 2. Using a T20® TORX® screwdriver, remove the burner base. 3. Apply masking tape to the end of a 7 mm nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside. C A D B To Convert TripleTier® Flame Burners (on some models) 1. Remove burner cap. 2. Remove the burner head using a size T20® TORX® screwdriver. 3. Remove the plate on the external gas orifice spud. A B C D A. Igniter electrode B. Gas tube opening C. Burner cap D. Burner base 4. Gas orifice spuds are stamped with a number, marked with 1 color dot, and have a groove in the hex area. Replace the Natural gas orifice spud with the correct LP gas orifice spud. A A. Burner caps B. Burner heads C. External gas orifice spud access plate D. Internal gas orifice spud IMPORTANT: The TripleTier® Flame burner has 2 gas orifice spuds. Do not forget to change the external gas orifice spud located under the plate. A B C A. Groove Refer to the following chart for correct LP gas orifice spud placement. LP Gas Orifice Spud Chart for Standard Surface Burners Burner Location Burner Rating Color Size Right front Left front Right rear Left rear 5,000 Btu/h 13,000 Btu/h 10,000 Btu/h 5,000 Btu/h Red Green Blue Red 0.70 mm 1.10 mm 0.95 mm 0.70 mm 5. Place Natural gas orifice spuds in plastic parts bag for future use and keep with package containing literature. 6. Replace burner cap. 7. Repeat steps 1-6 for the remaining burners, except for the TripleTier® Flame burner (on some models). See "To Convert TripleTier® Flame Burners" in the "LP Gas Conversion" section. A. Plate B. External gas orifice spud C. Internal gas orifice spud 4. Apply masking tape to the end of a 7 mm nut driver to help hold the internal gas orifice spud in the nut driver while changing it. Press nut driver down onto the internal gas orifice spud and remove by turning it counterclockwise and lifting out. Set internal gas orifice spud aside. 5. Use a 7 mm combination wrench to remove the external gas orifice spud. Turn counterclockwise to remove. Set external gas orifice spud aside. 6. Replace each Natural gas orifice spud with the correct LP gas orifice spud. Refer to the following chart for correct LP gas orifice spud placement. LP Gas Orifice Spud Chart for TripleTier® Flame Burners Burner Location Burner Rating Color Size Left front (external TripleTier® burner) 11,800 Btu/h Brown 1.00 mm Left front (internal TripleTier® burner) 2,200 Btu/h Orange 0.42 mm 7. Replace burner plate, head and cap. 8. Place Natural gas orifice spuds in plastic parts bag for future use and keep with package containing literature. 17