KitchenAid KUDL15FXSS Installation Guide - Page 11

Install Moisture Barrier, under a wood countertop

Get KitchenAid KUDL15FXSS PDF manuals and user guides View all KitchenAid KUDL15FXSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Option C, Waste disposer - with air gap Option D, No waste disposer - with air gap 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle-nose pliers to remove plug. 3. Connect black end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 4. Attach drain hose to air gap with large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp (not provided). 5. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from air gap to disposer inlet. 1. Connect black end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 2. Attach drain hose to air gap with large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to 5.1 cm) screw-type clamp (not provided). 3. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from waste tee to air gap. Install Moisture Barrier (under a wood countertop) 1. Make sure the area under the cabinet is clean and dry for installation of the moisture barrier. 2. Remove the backing of the moisture barrier and apply to underside of the countertop along the front edge of the counter. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
11
Option C, Waste disposer – with air gap
Option D, No waste disposer – with air gap
Install Moisture Barrier
(under a wood countertop)
1.
Make sure the area under the cabinet is clean and dry for
installation of the moisture barrier.
2.
Remove the backing of the moisture barrier and apply to
underside of the countertop along the front edge of the
counter.
1.
Using a hammer and screwdriver,
knock plug into disposer.
2.
Use needle-nose pliers to remove
plug.
3.
Connect black end of drain hose to
air gap and cut if needed.
NOTE:
Do not cut ribbed section.
4.
Attach drain hose to air gap with
large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1
¹⁄₂
"
to 2" (3.8 to 5 cm) screw-type clamp
(not provided).
5.
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from air gap to
disposer inlet.
1.
Connect black end of drain hose to
air gap and cut if needed.
NOTE:
Do not cut ribbed section.
2.
Attach drain hose to air gap with
large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1
¹⁄₂
"
to 2" (3.8 to 5.1 cm) screw-type
clamp (not provided).
3.
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from waste tee
to air gap.