LG 32LH255H User Manual - Page 150

Reference: LT2002 Cloning Procedure Troubleshooting, Problem, Possible Causes, Possible Solutions

Get LG 32LH255H PDF manuals and user guides View all LG 32LH255H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

Reference: LT2002 Cloning Procedure Troubleshooting Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer will be damaged. Reset Clone After Static Shock After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked "RESET" to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time. Note The LT2002 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.) Clone Programmer Troubleshooting Problem Possible Cause(s) Clone Programmer Clone copies Setup in less than 30 seconds • Not enough time to copy entire TV setup. Remote does not operate clone. • Wrong Installer remote. LED does not blink. • M.P.I. cord not connected. • TV not turned on. • Weak batteries. Clone menu hard to read. • Weak signal. No time set. • Time not available. Clone not working. • Clone programmer problem. Clone Scans Channels more than once. • Clone should only scan channels once. Possible Solution(s) - Press Reset on clone programmer, redo teach/learn. (Teach/Learn should take a minimum of 1 minute.) - Only use an LG Installer remote to operate clone programmer with TV. - Connect M.P.I. cord properly, assure good connection. - TV must be powered On for clone to work. - Install 4 fresh AA high-quality alkaline batteries. - Connect TV to a reliable Analog channel signal source. - Set time on a TV, copy time to Clone Programmer. - Try a different LT2002 Clone programmer. - Reset Clone Programmer. - Retry cloning again. Master and Other TVs Cloning did not work. • Procedure interrupted. • Different TV models. • Step(s) omitted or not performed. - Wait until procedure complete message is displayed. - Cloning is only possible with identical model TVs. - Reread pages 7-8-9 to be sure all tasks were performed. Clone time disappeared. • Batteries were removed. - Batteries must remain installed to retain time settings. New Setup not present. • TV not reset. - Disconnect newly-cloned unit from power for 5 seconds. • After cloning operations are complete, just unplug the LT2002 from the TV. • If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels. 206-4118 PAGE 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
PAGE 41
206-4118
Reset Clone After Static Shock
After replacing exhausted batteries, or if the programmer
behaves strangely after a static shock, use a paper clip or simi-
lar instrument inserted through the small hole marked ”RESET”
to activate the internal reset switch and restore normal opera-
tion. After a reset, check the real-time clock setting. It may be
necessary to reset the Clone Programmer clock from a TV con-
taining the correct time.
Note
The LT2002 programmer is designed to be used with TVs con-
taining the 221-01006 and later processors. Use with earlier TV
sets may give unpredictable results. Processors used before the
221-01006-04 have a limited screen display capability. They
cannot display entire screens as shown in the quick setup
instructions accompanying the LT2002 clone programmer. Use
the printed menu illustrations on the quick setup sheet sup-
plied with the Clone as an aid to making your programming
choices. (Although the menus are not all displayed, the clone
functions all operate normally.)
• After cloning operations are complete, just unplug the LT2002 from the TV.
• If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels.
Clone Programmer Troubleshooting
Problem
Possible Cause(s)
Possible Solution(s)
Clone Programmer
Clone copies Setup in
• Not enough time to copy
- Press Reset on clone programmer, redo teach/learn.
less than 30 seconds
entire TV setup.
(Teach/Learn should take a minimum of 1 minute.)
Remote does not
• Wrong Installer remote.
- Only use an LG Installer remote to operate clone programmer
operate clone.
with TV.
LED does not blink.
• M.P.I. cord not connected.
- Connect M.P.I. cord properly, assure good connection.
• TV not turned on.
- TV must be powered On for clone to work.
• Weak batteries.
- Install 4 fresh AA high-quality alkaline batteries.
Clone menu hard
• Weak signal.
- Connect TV to a reliable Analog channel signal
to read.
source.
No time set.
• Time not available.
- Set time on a TV, copy time to Clone Programmer.
Clone not working.
• Clone programmer
- Try a different LT2002 Clone programmer.
problem.
- Reset Clone Programmer.
Clone Scans Channels
• Clone should only scan
- Retry cloning again.
more than once.
channels once.
Master and Other TVs
Cloning did not work.
• Procedure interrupted.
- Wait until procedure complete message is displayed.
• Different TV models.
- Cloning is only possible with identical model TVs.
• Step(s) omitted or
- Reread pages 7-8-9 to be sure all tasks were performed.
not performed.
Clone time disappeared.
• Batteries were removed.
- Batteries must remain installed to retain time settings.
New Setup not present.
• TV not reset.
- Disconnect newly-cloned unit from power for 5 seconds.
Reference: LT2002 Cloning Procedure Troubleshooting
Warning: Do not use LT2002 while any PPV card is
installed in TV or clone programmer will be damaged.