LG 47LB1DA Owners Manual - Page 115
m][b]/ ] Is_t [D]/ ] [Data][Crl
View all LG 47LB1DA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 115 highlights
DataS: m z O X 114 All data are transmitted by Hexadecimal code lwoiOne part Channel: 6th bit This bit is used in a cable-ready system. Using physical channek 5th bit If the channel band is NTSC air or NTSC cable, channd tuning can be done by only physical channel, tn this case, using physical channel bit must be low(O). gut if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. if the physka[ channel sending is meaningful, you should set this bit low(O). If the physical channel sending is meaningless, you should set this bit high(1 ), Example) 1_.Analog channel: NTSC cable, channel number(SS), main picture Command: ma 00 25 xx xx xx xx 01 attribute(0x0] ): main picture, two part(it's not mandatory), using physical channel, NTSC cable "xx' data: don't care major and minor channel number in case analog channd tuning. 2. Digital channel: ATSC aig channel number(don't know physical channel, major(S0), minor(S)), sub picture Command: ma 00 xx 00 1E 00 03 A2 attrlbute(0xA2): sub picture, two part not using physical channel ATSC air _x×_ data: don't care analog channel number in case digital channel tuning. 3. Digital channel: ATSC ai_ channel number(physi- cal(20),major(20), mino_ (3)), sub picture Command: ma O0 T4 O0 14 00 OS 82 aHribu_e('0xg2): sub pidu_e, two Dart. using physica channel. A[SC am Ackn¢_wfr_,d_men_a} [ _ Set tDJ [ _ [OK] IDataOJ [Data] [ IL;ata2_ [Data 51 _Data4} [x_ Ial [ ] [Set _D_ [ ] [NG t [DataO[ [x] 25. _annel Add/Del (Command: m b) To add and delete the channels T_._s_iss_[om,,][b]/ ] Is_t [D]/ ] [Data][Crl Data 0: Channel Delete Data 1 : Channel Add A_Mii_,k*d#e_[b_] [ ] [S&t ID]I[ ] [OK/NG] [Data1[×] 26. Key (Command: m c) To send IR remote key code, Tr_ns,_,isdo_ [m] H [ [ iS,at ID][ ] [Data[ [C_]s Data Key {.ode; Refer to page 1t6. A_k_oMed_emen_ [c] [ ] [Set ID'] [ ] [O_JNG] [Da_a] [x] 27. Input select(Command: x b) (Main Picture Input) To select input sou_'ce for TV. T_smisS_o1__[]b] [] [SetI:D][ ] [Dat_][Cq Data 00 : UT'V (Antenna) Da_ 01 : DTV (Cable) Data 10 : Analog (Antenna) Data 20 : AVl Data 11 : Analog (Cable) Data 21 : AV2 Data 40 : Com_nent 1 Data 4-'I : Component 2 Data 50 : RGB DTV Data 60 : RC;B PC Da_ 90: HDMHiDV[ Data 91 HDM[2 Ack_owt_*dgeme_[b][ ][Set ID][ ] [OK/NG] [Di_a] IX] 28. PIP Input Select(Comman& x y) To adjust input source lot sub picture in PiP mode_ Tr_msmls@_nI×] [y] [] [Set ID] [ [ [Data] [Cr] Data 00 : DTV (Antenna) Data 01 : DTV (Cable) Data 10 : Analog (Antenna) Data ll : Analog (Cable) Data 20 : AV1 Data 21 : AV2 Ack_oMedg_:_m_,r_t[yII] _Set ID] [ _ IOK/NG] [Data] [q