LG DLEX9500K Owners Manual - Page 18

Warning

Get LG DLEX9500K PDF manuals and user guides View all LG DLEX9500K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

18 INSTALLATION Reversing the Cabinet Components 1. Remove the two screws and the latch assembly from the left side of the opening. 2. Rotate the latch assembly and remount it on the right side of the opening with the two screws. 3. Switch the two caps. Untie the twist tie and remove the small cap from the side of the wire harness on the top right of the cabinet. Make sure the wire harness does not slip back into the cabinet. 4. Remove the left cap by gently prying it up with a flat blade screwdriver, being careful not to scratch the paint. Disconnect the wire harness attached to the cap by pressing the tabs on either side. 5. Attach the left cap to the wire harness on the top right of the cabinet. Snap the cap into place. 6. Attach the twist tie and the small cap removed in step 1 to the side of the wire harness on the bottom left of the cabinet. The wire harness will be attached to the harness in the door. 7. Unscrew the four decorative screws from the left side of the cabinet and insert them into the matching holes on the right side of the cabinet. Cap L Mounting the Door 1. Align the hinge with the mounting holes. 2. While supporting the door, fasten the four hinge screws. Latch Final Check 1. Check that the door closes and latches properly. Cap L wWarning Be sure to support the weight of the door while inserting the hinge screws. Preparing to Remount the Door 1. While supporting the door, move the door into position with the hinge on the left side. 2. Connect the wire harness from the hinge to the connector on the lower left side of the cabinet. Hinge Hole Harness Connector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
18
Reversing the Cabinet Components
1. Remove the two screws and the latch assembly from
the left side of the opening.
2. Rotate the latch assembly and remount it on the right
side of the opening with the two screws.
3. Switch the two caps. Untie the twist tie and remove
the small cap from the side of the wire harness on the
top right of the cabinet. Make sure the wire harness
does not slip back into the cabinet.
4. Remove the left cap by gently prying it up with a flat
blade screwdriver, being careful not to scratch the
paint. Disconnect the wire harness attached to the
cap by pressing the tabs on either side.
5. Attach the left cap to the wire harness on the top right
of the cabinet. Snap the cap into place.
6. Attach the twist tie and the small cap removed in step
1 to the side of the wire harness on the bottom left of
the cabinet. The wire harness will be attached to the
harness in the door.
7. Unscrew the four decorative screws from the left side
of the cabinet and insert them into the matching
holes on the right side of the cabinet.
Latch
Cap L
Cap L
w
WARNING
Be sure to support the weight of the door while
inserting the hinge screws.
Preparing to Remount the Door
1. While supporting the door, move the door into
position with the hinge on the left side.
2. Connect the wire harness from the hinge to the
connector on the lower left side of the cabinet.
Harness
Connector
Hinge Hole
Mounting the Door
1. Align the hinge with the mounting holes.
2. While supporting the door, fasten the four hinge
screws.
Final Check
1. Check that the door closes and latches properly.
INSTALLATION