LG DLG5966W User Guide - Page 20

Duct Condition Testing - problems

Get LG DLG5966W - 27in Gas Dryer PDF manuals and user guides
UPC - 048231009164
View all LG DLG5966W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

INSTALLATION INSTRUCTIONS DUCT CONDITION TESTING Your dryer features FlowSense™, an innovative sensor system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint build-up and free of restrictions allows clothes to dry faster, reduces energy use, and helps prevent fires. When the dryer is first installed, the duct condition test must be performed. This alerts you to any existing problems before the dryer is used. The dryer also saves this information to compare and measure future changes. To activate the duct condition test cycle: 1 Press and hold the DAMP DRY BEEP and TEMP CONTROL buttons at the same time. While holding these buttons, press POWER ON/OFF. 2 The dryer will show lnS in the number display to indicate that it is in duct condition testing mode. 3 Press START/PAUSE. The dryer will run for approximately 2 minutes to test for blockages or restrictions to air flow in the ductwork. If no bars are shown in the display, the ductwork is free from blockages or restrictions. Correct Venting Restricted or Blocked Airflow Avoid long runs or runs with multiple elbows or bends. Check for blockages and lint buildup. If all bars are lit, the dryer ductwork has a blockage that needs to be removed immediately. Make sure the ductwork is not crushed or restricted. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Your dryer features FlowSense
™
, an innovative
sensor system that automatically detects
blockages and restrictions in dryer ductwork.
Keeping ductwork clean of lint build-up and free
of restrictions allows clothes to dry faster, reduces
energy use, and helps prevent fires.
When the dryer is first installed, the duct condition
test
must
be performed. This alerts you to any
existing problems before the dryer is used. The
dryer also saves this information to compare and
measure future changes.
To activate the duct condition test cycle:
Press and hold the DAMP DRY BEEP and
TEMP CONTROL buttons at the same time.
While holding these buttons, press POWER
ON/OFF.
The dryer will show lnS in the number display
to indicate that it is in duct condition testing
mode.
Press START/PAUSE. The dryer will run for
approximately 2 minutes to test
for blockages or restrictions to air
flow in the ductwork.
DUCT CONDITION TESTING
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
If no bars are shown in the display,
the ductwork is free from blockages or
restrictions.
If all bars are lit, the dryer ductwork
has a blockage that needs to be
removed immediately.
Correct Venting
1
2
3
Restricted or Blocked Airflow
Avoid long runs or runs with multiple elbows
or bends.
Check for blockages and lint buildup.
Make sure the ductwork is not crushed
or restricted.
20