LG DLG5988SM User Guide - Page 24

cONNEcTiNG

Get LG DLG5988SM PDF manuals and user guides View all LG DLG5988SM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

INSTALLATIONINSTRUCTIONS cONNEcTiNG ELEcTRic DRYERS {cont.) USA ONLY WARN|NG: • Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload. • Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. Three-wire Connection for Electric Dryers: Direct wire = A 3-wire connection is NOT permitted on new construction after January 1, 1996. = A UL-listed strain relief is required. = Use UL-listed 3-wire #10 AWG=minirnurn copper conductor cable. = Allow at least 5 ft (1.5 m) length to allow for removal and reinstallation of the dryer. 1" (2.5 cm) I-4 Terminal Block UL-Listed Strain Relief J Remove 31/2inches (8.9 cm) of the outer covering from the wire. Strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three wires into a hook shape. UL-Listed 3-Wire Power Cord Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief. .....:...... :::: .......J.;.,.... Hot Black) Neutral Hot (White) (Red) Ground Screw o i i 'j x I .......G. round Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. TIGHTEN ALL SCREWS SECURELY. Reinstall the terminal block access cover. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
INSTALLATION
INSTRUCTIONS
cONNEcTiNG
ELEcTRic
DRYERS {cont.)
USA
ONLY
WARN|NG:
• Connect
the
power
cord
to
the
terminal
block.
Each
colored
wire
should
be
connected
to
same
color
screw.
Wire
color
indicated
on
manual
is
connected
to
the
same
color
screw
in
block.
Failure
to
follow
these
instructions
may
result
in
a short
or
overload.
• Grounding
through
the
neutral
conductor
is
prohibited
for:
(1) new
branch-circuit
installations,
(2) mobile
homes,
(3) recreational
vehicles,
and
(4) areas
where
local
codes
prohibit
grounding
through
the
neutral
conductor.
Three-wire
Connection
for
Electric
Dryers:
Direct
wire
= A 3-wire
connection
is
NOT permitted
on new
= Use UL-listed
3-wire
#10 AWG=minirnurn
construction
after January
1, 1996.
copper
conductor
cable.
= A UL-listed
strain relief is required.
= Allow at least 5 ft (1.5 m) length to allow for
removal and reinstallation
of the dryer.
1"
(2.5 cm)
I-4
J
Remove 31/2inches (8.9 cm) of the outer
covering
from the wire. Strip
1 inch (2.5 cm)
insulation
from each wire. Bend the ends of
the three wires into a hook shape.
Terminal
Block
UL-Listed
Strain
Relief
UL-Listed
3-Wire
Power
Cord
Remove
the terminal
block access
cover
on the upper back of the dryer. Install a
UL-listed
strain relief into the power
cord
through-hole;
then thread the power
cable
prepared
in Step 1 through
the strain relief.
........
:
......
::::
Hot
Neutral
Hot
Black)
(White)
(Red)
.............
J;,
o
i
i
x
Ground
Screw
'
j
I
........
Ground
Attach
the two hot leads of the power
cord
to the outer terminal
block
screws. Attach
the neutral wire to the center terminal
block
screw. Connect the external ground
(if
required
by local codes) to the green ground
screw. TIGHTEN ALL SCREWS
SECURELY.
Reinstall the terminal
block access
cover.
24