LG DLG8388NM Owners Manual - Page 16

Review, the following, options, to determine, the appropriate, electrical, connection, for your home - no heat

Get LG DLG8388NM PDF manuals and user guides View all LG DLG8388NM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Review the following options to determine the appropriate electrical connection for your home: Use the instructions in this section if your home has a 4-wire receptacle (NEMA type 14-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord. Use the instructions in this section if your home has a 3-wire receptacle (NEMA type 10-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord. If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box Important : Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, and (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. Prepare minimum 5fl(l.52m) of length in order for dryer to be replaced. First, peel 5 inches (12.7cm) of coveting material from end. Strip 5 inches of ground wire insulation. After cutting 172inch (3.8cm) from 3 other wires peel insulation back linch (2.5cm). Make ends of 3 wires a hook shape. ¢ Then, put the hooked shape end of the wire under the screw of the terminal block(hooked end facing rightward) and pinch the hook together and screw tightly. If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker box • Screw power supply wire to the terminal block, Colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Otherwise, excessive current is applied resulting in damages on product and heating failure, 16 1. Connect neutral wire(white) of power cord to center terminal block screw. 2. Connect red and black wire to the left and right terminal block screws. 3. Connect ground wire(green) of power cord to external ground screw and move neutral ground wire of appliance and connect it to center screw. 4. Make sure that the strain relief screw is tightened. and be sure that all terminal block nuts are on tight and power cord is in right position. Center terminal block screw(silver) Neutral grounding wire(white) Neutral wire (white or center wire) Strain relief Green wire of power cord External ground connector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
Review
the following
options
to determine
the appropriate
electrical
connection
for your home:
if your
home
has
Use
the instructions
in this
section
a 4-wire
receptacle
(NEMA
type
14-30R)
and
you
will
be using
a UL
listed,
120/240
volt
minimum,
30 amp,
dryer
power
supply
cord.
Use
the
instructions
in this
section
if your
home
has
a 3-wire
receptacle
(NEMA
type
10-30R)
and you
will be using
a UL listed,
120/240
volt
minimum,
30 amp,
dryer
power
supply
cord.
Important
:
Grounding
through
the neutral
conductor
is prohibited
for (1) new branch-circuit
installations,
(2) mobile
homes,
and (3) recreational
vehicles,
and
(4) areas where
local codes
prohibit
grounding
through
the neutral
conductor.
Prepare
minimum
5fl(l.52m)
of length
in order
for
dryer to be replaced.
First, peel 5 inches (12.7cm)
of coveting
material from
end. Strip 5 inches of ground wire insulation.
After
cutting
172inch (3.8cm) from 3 other wires peel
insulation back
linch (2.5cm). Make ends of 3 wires a
hook shape.
¢
If this type
is available
at your
home.
you will
be
connecting
to a fused
disconnect
or circuit
breaker
box
Then,
put the hooked
shape end of the wire under
the
screw
of the terminal
block(hooked
end facing
rightward)
and pinch the hook together
and screw
tightly.
16
If this type
is available
at your
home.
you
will be
connecting
to a fused
disconnect
or circuit
breaker
box
•
Screw power supply wire to the terminal block,
Colored wire should be connected to same color
screw. Wire color indicated on manual is
connected to the same color screw in block.
Otherwise, excessive current is applied resulting
in damages on product and heating
failure,
1. Connect
neutral
wire(white)
of power
cord to center
terminal
block
screw.
2. Connect
red and black wire to the left and right
terminal
block
screws.
3. Connect
ground
wire(green)
of power cord to external
ground
screw and move
neutral
ground
wire of
appliance
and connect
it to center
screw.
4. Make
sure that the strain relief
screw
is tightened.
and be sure that all terminal
block nuts are on tight and
power cord is in right position.
Center
terminal
block
screw(silver)
Neutral
grounding
wire(white)
Neutral
wire
(white
or center
wire)
Strain
relief
Green
wire of power
cord
External
ground
connector