LG DLGX9001W Owners Manual - English Spanish - Page 23

Connecting the Inlet Hose

Get LG DLGX9001W PDF manuals and user guides View all LG DLGX9001W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

ENGLISH INSTALLATION 23 Connecting the Inlet Hose The dryer must be connected to the cold water tap using the new water supply hose. Do not reuse old hoses. NOTE t8BUFSTVQQMZQSFTTVSFNVTUCFCFUXFFOQTJBOEQTJ oL1B  t%POPUTUSJQPSDSPTTUISFBEXIFODPOOFDUJOHUIFJOMFUIPTFUPUIFWBMWF t*GUIFXBUFSTVQQMZQSFTTVSFJTNPSFUIBOQTJ L1B BQSFTTVSFSFEVDJOHWBMWFNVTUCFJOTUBMMFE t1FSJPEJDBMMZDIFDLUIFDPOEJUJPOPGUIFIPTFBOESFQMBDFUIFIPTFJGOFDFTTBSZ t3FQMBDFJOMFUIPTFTBGUFSöWFZFBSTPGVTFUPSFEVDFUIFSJTLPGIPTFGBJMVSF t3FDPSEIPTFJOTUBMMBUJPOPSSFQMBDFNFOUEBUFTPOUIFIPTFTGPSGVUVSFSFGFSFODF 1. Check the rubber seal in the inlet hose. Two rubber seals are supplied with each inlet hose. They are used for preventing water leaks. Make sure the connection to the cold water tap is tight. Hose connector 3. Connect the hose to the dryer. t$POOFDUUIFXBUFSTVQQMZIPTFUPUIFESZFSJOMFUWBMWF tightly by hand and then tighten another 2/3 turn with pliers. Make sure that there are no kinks in the hoses and that they are not crushed. 2. Check the installation type. Rubber seal Y connector Short hose Long hose Y connector WITH WASHER WITHOUT WASHER $POOFDUBMMXBUFSTVQQMZIPTFTUJHIUMZCZIBOEBOE UIFOUJHIUFOBOPUIFSUVSOXJUIQMJFST 8*5)8"4)&38IFODPOOFDUJOHUIFESZFSUPUIF TBNFGBVDFUBTBXBTIFS a. Shut off the cold water tap and remove the washer hose. b. Connect the short hose to the Y-connector using one of the rubber seals. c. Connect the other end of the short hose to the cold water faucet. d. Connect the long dryer hose to one side of theY-connector and connect the washer hose to the other side. 8*5)0658"4)&3*GUIFESZFSEPFTOPUTIBSFUIF DPMEXBUFSUBQXJUIBXBTIFS a. Connect the straight end of the long hose to the cold water faucet. NOTE t#FGPSFDPOOFDUJOHUIFXBUFSMJOFUPUIFESZFS øVTI several gallons of water into a drain or bucket. This will help prevent foreign particles such as sand and scale from clogging the dryer inlet valve. t%POPUPWFSUJHIUFO%BNBHFUPUIFDPVQMJOHDBOSFTVMU 4. Turn on the cold water faucet. 5. Check for leaks at the Y-connector (if used) and in all hoses. NOTE t*GBOZMFBLTBSFGPVOE TIVUPòUIFXBUFSGBVDFU  remove the hose and check the condition of the rubber seals.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
23
ENGLISH
1.
Check the rubber seal in the inlet hose. Two rubber
seals are supplied with each inlet hose. They are used
for preventing water leaks. Make sure the connection
to the cold water tap is tight.
2. Check the installation type.
a.
Shut off the cold water tap and remove the washer hose.
b.
Connect the short hose to the Y-connector using one
of the rubber seals.
c.
Connect the other end of the short hose to the cold
water faucet.
d.
Connect the long dryer hose to one side of theY-connector
and connect the washer hose to the other side.
a.
Connect the straight end of the long hose to the cold
water faucet.
Connecting the Inlet Hose
The dryer must be connected to the cold water tap using the new water supply hose. Do not reuse old hoses.
3. Connect the hose to the dryer.
tightly by hand and then tighten another 2/3 turn with
pliers.
Make sure that there are no kinks in the hoses and that
they are not crushed.
4. Turn on the cold water faucet.
5.
Check for leaks at the Y-connector (if used) and in all
hoses.
NOTE
remove the hose and check the condition of the
rubber seals.
NOTE
several gallons of water into a drain or bucket. This will
help prevent foreign particles such as sand and scale
from clogging the dryer inlet valve.
NOTE
Hose
connector
Y connector
Rubber
seal
Long
hose
WITH WASHER
WITHOUT WASHER
Short
hose
Y connector
INSTALLATION