Lasko 2510 User Manual - Page 4

Model 2510, Model 2535, Modelo 2510 - manual

Get Lasko 2510 PDF manuals and user guides View all Lasko 2510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

MODEL 2535 MODEL 2510 MODELO 2510 OPERATION (Figures 5 and 6) This Fan may be operated by the Manual Controls located on top of the unit (as shown in Figure 5) or by the Remote Control (shown in Figure 6). 1. Place the Fan on a firm and level surface. CAUTION: Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors. 2. Plug the cord set into a 120 volt outlet. Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater. 3. Turn the Fan ON by pressing the Power Button ( ). 4. SPEEDS: Press the Fan Speed Button ( ) to desired speed setting. Each time the Fan Speed Button is pressed, the speed will change from High (3), to Medium (2), to Low (1). When the Fan is turned OFF and ON again, the unit will resume the speed at which it was turned OFF. 5. OSCILLATION: Press the Oscillation Button ( ) to start and stop the oscillation function. 6. TIMER: The timer function allows the unit to be set to operate for a length of time from 1 hour to 7 hours, in increments of 1 hour. Press the Timer Button ( ) to set the length of time desired. Each time the timer button is pressed, the time is increased by 1 hour. After reaching 7 hours, pressing the timer button once more will reset the Fan to continuous running. The lights on the front of the unit will light up appropriately with the length of time that the Fan is set for. 7. To turn the Fan OFF, press the Power Button ( ) and unplug the unit from the electrical outlet. ENSAMBLADO 1. Cuidadosamente retire el ventilador de la bolsa plástica y de la caja. Para facilidad de ensamblado, coloque el ventilador en forma horizontal para que la parrilla frontal esté apuntando hacia abajo. 2. Arme las Bases de Apoyo interconectando las Salientes en la Base de Apoyo A dentro de los Orificios de Salientes en la Base de Apoyo B. Introduzca el Cable Eléctrico a través del orificio grande en el centro de la Montura de la Base de Apoyo. (Figura 1) 3. Asegure los (4) Tornillos en los cuatro orificios de la parte inferior de la base. (Figura 2) 4. Alinee las Lengüetas de Alineación de la Montura de la Base de Apoyo con las ranuras de alineación en la parte inferior del ventilador, teniendo cuidado de que el canal del cable en la parte inferior de la base de apoyo debe estar apuntando hacia la parte posterior del ventilador. (Figura 3) 5. Asegure la Montura de la Base de Apoyo a la parte inferior del ventilador con (4) Tornillos de Largo. Suavemente elimine cualquier sobrante del Cable Eléctrico y colóquelo en el Orificio de Colocación del Cable. (Figura 4) Ranura de Alineación Lengüeta de Alineación de la Montura de la Base de Apoyo Montura de la Base de Apoyo Canal del Cable Oscillation Button Timer Button Speed Button Power Button Base de Apoyo B Base de Apoyo A Figura 3 Salientes Figura 1 Montura de la Unidad de base a Parte Inferior Montura de la Base de Apoyo Montura de la Base de Apoyo - Vista Inferior Montura de la Base de Apoyo Rev. G 10/15 Figure 5 Tornillos 4 2510ES Rev. G 10/15 Tornillos Figura 2 9 Orificio de Colocación del Cable Cable Eléctrico Figura 4 2510ES

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
MODEL 2510
OPERATION
(Figures 5 and 6)
This Fan may be operated by the Manual Controls located
on top of the unit (as shown in
Figure 5
) or by the Remote
Control (shown in
Figure 6)
.
1. Place the Fan on a firm and level surface.
CAUTION:
Plastic or rubber tabs, like the feet on this unit,
may stick to furniture surfaces and/or hardwood floors. The
unit may leave a residue that could darken, stain or leave
permanent blemishes on the finish of certain furniture sur-
faces, including wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they
may slip partially or completely out of the
receptacle with only the slight movement of
the attached cord. Receptacles in this con-
dition may overheat and pose a serious fire
hazard; if covered by a curtain or drape, the
fire hazard is even greater.
Rev. G 10/15
4
2510ES
Rev. G 10/15
9
2510ES
MODEL 2535
3. Turn the Fan ON by pressing the
Power Button
(
).
4.
SPEEDS:
Press the
Fan Speed Button
(
) to desired
speed setting.
Each time the Fan Speed Button is
pressed, the speed will change from High (3), to Medium
(2), to Low (1). When the Fan is turned OFF and ON again,
the unit will resume the speed at which it was turned
OFF.
5.
OSCILLATION:
Press the
Oscillation Button
(
) to start
and stop the oscillation function.
6.
TIMER:
The timer function allows the unit to be set to
operate for a length of time from 1 hour to 7 hours, in
increments of 1 hour.
Press the
Timer Button
(
) to set
the length of time desired. Each time the timer button is
pressed, the time is increased by 1 hour.
After reaching
7
hours, pressing the timer button once more will reset
the Fan to continuous running. The lights on the front of
the unit will light up appropriately with the length of time
that the Fan is set for.
7. To turn the Fan OFF, press the
Power Button
(
) and
unplug the unit from the electrical outlet.
Figure 5
Oscillation
Button
Power
Button
Timer Button
Speed Button
ENSAMBLADO
1. Cuidadosamente retire el ventilador de la bolsa plástica y de
la caja. Para facilidad de ensamblado, coloque el ventilador
en forma horizontal para que la parrilla frontal esté apuntando
hacia abajo.
2. Arme las
Bases de Apoyo
interconectando las
Salientes
en
la
Base de Apoyo A
dentro de los
Orificios de Salientes
en la
Base de Apoyo B
. Introduzca el
Cable Eléctrico
a través del
orificio grande en el centro de la
Montura de la Base de Apoyo
.
(Figura 1)
3. Asegure los
(4) Tornillos
en los cuatro orificios de la parte inferior
de la base.
(Figura 2)
4. Alinee las
Lengüetas de Alineación de la Montura de la Base
de Apoyo
con las ranuras de alineación en la parte inferior del
ventilador, teniendo cuidado de que el canal del cable en la
parte inferior de la base de apoyo debe estar apuntando hacia
la parte posterior del ventilador.
(Figura 3)
5. Asegure la
Montura de la Base de Apoyo
a la parte inferior
del ventilador con
(4) Tornillos de Largo
. Suavemente elimine
cualquier sobrante del
Cable Eléctrico
y colóquelo en el
Orificio
de Colocación del Cable
.
(Figura 4)
Tornillos
Montura de la
Base de Apoyo
Cable Eléctrico
Orificio de
Colocación del
Cable
Figura 4
Montura de la Unidad de base a Parte Inferior
MODELO 2510
Ranura de
Alineación
Lengüeta de
Alineación de la
Montura de la Base
de Apoyo
Figura 3
Canal del Cable
Figura 2
Montura de la Base de Apoyo - Vista Inferior
Montura
de la Base
de Apoyo
Tornillos
Figura 1
Base de
Apoyo B
Base de
Apoyo A
Salientes
Montura de la Base de Apoyo