Lasko T38400 User Manual - Page 2

WARNING IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock and injury to persons: Read all instructions before using this Fan. WARNING TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS: DO NOT use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints, gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the containers for these products! ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should be replaced by a qualified electrician. ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan when not in use. BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source. The Blue Plug™ on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug. THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one way. Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced. CAUTION • AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these devices may overheat and cause a fire hazard. • DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire hazard. • ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning. • NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur. • DO NOT block, cover or obstruct air flow to or from the Fan while in operation. • DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may create a shock hazard. • DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. • NEVER use a single extension cord to operate more than one Fan or other electrical device. • DO NOT use this Fan if it has been damaged or is not functioning properly. • Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs, move the Fan to another location. • Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan. • THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings. • THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for hazardous locations. Models T38400/T38415 Lasko Products, LLC 820 Lincoln Avenue West Chester, PA 19380 www.lasko.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. "NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and the receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help." SAVE THESE INSTRUCTIONS NEW 10/20 2 T38400_T38415ES Partes Incluidas 2 1 3 1 Cuerpo 3 Base de Soporte A 4 2 Control Remoto 4 Base de Soporte B Ensamblaje 1. Empuje a los jefes en la Base de Soporte B en las ranuras del jefe en la Base de Soporte A. Controles 2. Alinee la Montura de la Base de Apoyo con la Cuerpo. 3. Sostenga la Cuerpo en su lugar mientras gira la Montura de la Base de Apoyo en el sentido de las agujas del reloj hasta que deje de girar y encaje en su lugar. Botón de Encendido ENCENDIDO/APAGADO el Ventilador presionando el Botón de Encendido. Botón de Temporizador El temporizador se puede configurar para 8 horas. Continúe pulsando el Botón del Temporizador para llegar a la configuración de tiempo deseada. Botón de Velocidad La velocidad del ventilador se puede ajustar a 1, 2, 3, o 4. Botón de Oscilación Presione el Botón de Oscilación para iniciar y detener la función de oscilación. NEW 10/20 7 T38400_T38415ES