Lenovo ThinkCentre A52 Notice to New Zealand Users - Page 1

Lenovo ThinkCentre A52 Manual

Get Lenovo ThinkCentre A52 PDF manuals and user guides View all Lenovo ThinkCentre A52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Notice to New Zealand Users Conexant RD01-D850 Data Fax PCI Modem - PTC 211/03/066 1. The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. 2. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. This condition typically applies to 56 kbit/s modems. 3. This equipment does not fully meet Telecom's impedance requirements. Performance limitations may occur when used in conjunction with some parts of the network. Telecom will accept no responsibility should difficulties arise in such circumstances. 4. The equipment shall not be set up to make automatic calls to Telecom's 111 Emergency Service. 5. This device may be subject to ringing or bell tinkle when certain other devices are connected to the same line. If this occurs, the problem should not be referred to the Telecom Faults Service. 6. This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers. 7. Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the application software. The application software shall be set to operate within the following limits for compliance with Telecom's specifications: v The S0 register must contain a value of 0 for no auto-answer or a value of 3 to 8 for auto answer. The factory default is 3. v The S6 register must contain a value of 4, 5, 6 or 7. The factory default of 4 is recommended. v The S7 register must contain a value of less than 80. The factory default is 60. v The S10 register must contain a value of less than 140. The factory default is 14. v The S11 register must contain a value of greater than 60. The factory default is 85. v There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation. v The equipment shall go on-hook for a period of not less than 30 seconds between the end of one call attempt and the beginning of the next attempt to the same number. v Automatic calls to different numbers shall be not less than 2 seconds apart. v Failure to set these parameters correctly could negate the User Rights under the Telecom Terms of Service.

  • 1
  • 2
Notice
to
New
Zealand
Users
Conexant
RD01-D850
Data
Fax
PCI
Modem
-
PTC
211/03/066
1.
The
grant
of
a
Telepermit
for
any
item
of
terminal
equipment
indicates
only
that
Telecom
has
accepted
that
the
item
complies
with
minimum
conditions
for
connection
to
its
network.
It
indicates
no
endorsement
of
the
product
by
Telecom,
nor
does
it
provide
any
sort
of
warranty.
Above
all,
it
provides
no
assurance
that
any
item
will
work
correctly
in
all
respects
with
another
item
of
Telepermitted
equipment
of
a
different
make
or
model,
nor
does
it
imply
that
any
product
is
compatible
with
all
of
Telecom’s
network
services.
2.
This
equipment
is
not
capable,
under
all
operating
conditions,
of
correct
operation
at
the
higher
speeds
for
which
it
is
designed.
Telecom
will
accept
no
responsibility
should
difficulties
arise
in
such
circumstances.
This
condition
typically
applies
to
56
kbit/s
modems.
3.
This
equipment
does
not
fully
meet
Telecom’s
impedance
requirements.
Performance
limitations
may
occur
when
used
in
conjunction
with
some
parts
of
the
network.
Telecom
will
accept
no
responsibility
should
difficulties
arise
in
such
circumstances.
4.
The
equipment
shall
not
be
set
up
to
make
automatic
calls
to
Telecom’s
111
Emergency
Service.
5.
This
device
may
be
subject
to
ringing
or
bell
tinkle
when
certain
other
devices
are
connected
to
the
same
line.
If
this
occurs,
the
problem
should
not
be
referred
to
the
Telecom
Faults
Service.
6.
This
equipment
should
not
be
used
under
any
circumstances
that
may
constitute
a
nuisance
to
other
Telecom
customers.
7.
Some
parameters
required
for
compliance
with
Telecom’s
Telepermit
requirements
are
dependent
on
the
application
software.
The
application
software
shall
be
set
to
operate
within
the
following
limits
for
compliance
with
Telecom’s
specifications:
v
The
S0
register
must
contain
a
value
of
0
for
no
auto-answer
or
a
value
of
3
to
8
for
auto
answer.
The
factory
default
is
3.
v
The
S6
register
must
contain
a
value
of
4,
5,
6
or
7.
The
factory
default
of
4
is
recommended.
v
The
S7
register
must
contain
a
value
of
less
than
80.
The
factory
default
is
60.
v
The
S10
register
must
contain
a
value
of
less
than
140.
The
factory
default
is
14.
v
The
S11
register
must
contain
a
value
of
greater
than
60.
The
factory
default
is
85.
v
There
shall
be
no
more
than
10
call
attempts
to
the
same
number
within
any
30-minute
period
for
any
single
manual
call
initiation.
v
The
equipment
shall
go
on-hook
for
a
period
of
not
less
than
30
seconds
between
the
end
of
one
call
attempt
and
the
beginning
of
the
next
attempt
to
the
same
number.
v
Automatic
calls
to
different
numbers
shall
be
not
less
than
2
seconds
apart.
v
Failure
to
set
these
parameters
correctly
could
negate
the
User
Rights
under
the
Telecom
Terms
of
Service.