Lexmark X264 Technical Reference - Page 12

PostScript paper tray support, Tray selected with tray operators - manual

Get Lexmark X264 PDF manuals and user guides View all Lexmark X264 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

PostScript paper tray support When the printer receives one of the operators listed in "Tray selected with tray operators" on page 12, it performs the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and paper is fed from this tray. • The printer checks the value of manualfeed in statusdict and the ManualFeed page device parameter. If either one is true, the printer sends a message to load the requested size in the manual feed tray or multipurpose feeder. • The PageSize Policy is set to 0 by means of setpagedevice. • The printer checks the paper size loaded in the current active source to determine if it matches the requested size. If the sizes match, the paper is fed from the active source. Note: The current active tray is the last source that was selected from the printer control panel or by the printer language. • If the requested size and the size loaded in the active source do not match, the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary. • If the requested media size is not found by the previous search, the following search order is used: - Tray 1 - Tray 2 - Tray 3 - Multipurpose Feeder - Tray 4 - Tray 5 • If the requested size cannot be located in any automatic source, a configurationerror is issued and the job is flushed. For printers that support automatic duplexing: • Automatic duplexing is not supported for custom-size paper or for envelopes in the multipurpose feeder. Automatic duplexing is supported from the multipurpose feeder for all other papers. • If the paper source is changed before the back side of a duplexed page prints, a blank back page prints, the paper source changes, and the information for the back side of the page is printed on the front side of a page sent from the new paper source. When these operators are used, it is equivalent to executing the following PostScript emulation sequence: >> setpagedevice where x y are the PageSize in points. Tray selected with tray operators = Supported X = Not supported Printer models Operator Tray selected (corresponding image X264dn, X363dn, X364dn, X463de, X464de, X466de, size is set) X364dw X466dte, X466dwe 11x17tray tray with 279.4 x 431.8-mm (11 x 17-in.) X X paper a3tray tray with A3-size paper X X PostScript (PS) emulation 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
PostScript paper tray support
When the printer receives one of the operators listed in “Tray selected with tray operators” on page 12, it performs
the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and
paper is fed from this tray.
•
The printer checks the value of
manualfeed
in
statusdict
and the ManualFeed page device parameter. If either
one is true, the printer sends a message to load the requested size in the manual feed tray or multipurpose feeder.
•
The PageSize Policy is set to 0 by means of
setpagedevice
.
•
The printer checks the paper size loaded in the current active source to determine if it matches the requested
size. If the sizes match, the paper is fed from the active source.
Note:
The current active tray is the last source that was selected from the printer control panel or by the printer
language.
•
If the requested size and the size loaded in the active source do not match, the sources are searched in the order
defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.
•
If the requested media size is not found by the previous search, the following search order is used:
–
Tray 1
–
Tray 2
–
Tray 3
–
Multipurpose Feeder
–
Tray 4
–
Tray 5
•
If the requested size cannot be located in any automatic source, a
configurationerror
is issued and the job is
flushed.
For printers that support automatic duplexing:
•
Automatic duplexing is not supported for custom-size paper or for envelopes in the multipurpose feeder.
Automatic duplexing is supported from the multipurpose feeder for all other papers.
•
If the paper source is changed before the back side of a duplexed page prints, a blank back page prints, the paper
source changes, and the information for the back side of the page is printed on the front side of a page sent from
the new paper source.
When these operators are used, it is equivalent to executing the following PostScript emulation sequence:
<< /PageSize [x y]/ImagingBBox null /Policies << /PageSize 0>> >>
setpagedevice
where
x y
are the PageSize in points.
Tray selected with tray operators
= Supported
X = Not supported
Printer models
Operator
Tray selected (corresponding image
size is set)
X264dn, X363dn, X364dn,
X364dw
X463de, X464de, X466de,
X466dte, X466dwe
11x17tray
tray with 279.4 x 431.8-mm (11 x 17-in.)
paper
X
X
a3tray
tray with A3-size paper
X
X
PostScript (PS) emulation
12