Lexmark X651DE SCS/TNe Emulation User's Guide
Lexmark X651DE - Mfp Laser Mono P/f/s/c Manual
 |
UPC - 734646093729
View all Lexmark X651DE manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark X651DE manual content summary:
- Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 1
Card for IPDS and SCS/TNe - SCS/TNe Emulation User's Guide Getting Started SCS/TNe in a LAN environment IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Thank you for purchasing the Card for IPDS and SCS/TNe. The card provides high quality IBM - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 2
Emulation User's Guide. Information on how to install the Card is in separate documentation shipped with your printer. If you need basic information on your printer and how to use it, please refer to the printer's specific documentation. Equipment Requirements and Specifications Supported Products - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 3
printer in this manual refers to both printers and MFPs. • Lexmark X466dte, X466dtwe • Lexmark X651de, X652de • Lexmark X654de, X656de • Lexmark X658de • Lexmark X734de, X736de, X738de • Lexmark X860de, X862de, X864de Required LAN Connection To use the SCS/TNe Emulation, the printer must have one - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 5
Basics Introduction IMPORTANT: Unless otherwise noted, the term printer refers to printers and MFPs, and the term control panel refers to operator panels and touch screens on these types of products. SCS/TNe MENU options settings can be changed and saved in three ways: • Use the control panel - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 6
Emulation user default settings remain in effect until you save new settings or restore the factory defaults by using one of the SCSxxxx Defaults options under MENU/Menus > Option Card Menu > SCS/TNe MENU > TNxxxE STEUP > TEST OPTIONS. xxxx stands for 3270 or 5250. Important Configuration Basics - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 7
may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings. Printer Setup Options Changes to printer settings under the various printer menus, such as Paper Menu and Settings, will - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 8
Understanding the Control Panel Introduction This chapter introduces the SCS/TNe MENU options as well as illustrating how how the control panel works. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs are illustrated here. If you are familiar with the use of - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 9
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 From a Ready status, press the MENU button . on the operator panel. This opens the menu index in the operator panel's screen. 2 Use the - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 10
. User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 11
the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel 13 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 12
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 14 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 13
the on-screen checkmark is next to the desired setting. press the Select button Country Code English (US) Fin/Swe Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 14
7 When the setting is saved, the display will revert to the previous menu level. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page If you want to check the value of a setting, press the Select button again. - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 15
is that the value you select consists of several fields. For example, if you select MENU > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #1 > SERVER 1 INFO > MSGQ 1 Name, you see the following display all the characters. Understanding the Operator Panel: Printer operator panel 17 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 16
a menu item that has a numerical value, you can usually choose between scrolling just as you would to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 17. Understanding the Operator Panel: Printer operator - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 17
MFP Touch Access the SCS/TNe Emulation options and settings from the operScreen ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer a New Value as a Setting" on page 20), enter a number ("Changing a Numerical Setting" on page 22), or enter a text - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 18
a new value 1 Navigate to the SCS/TNe MENU as explained in "MFP Touch Screen" on page 19. 2 For this example, touch SCS/TNe MENU. 3 Now you will see a list of menus. Touch or to scroll to the desired item. In this example locate and touch TN3270E SETUP. 4 Now you will see a list of menus - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 19
, touch (Back) and no changes will be saved. 9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e Setup > Network Setup > Server Info. 2 Touch the Keyboard symbol by - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 20
Enter (on some MFPs touch Submit) when you have completed the name. The screen returns to the previous menu level. 6 Touch (Submit) to save changes. Changing a Numerical Setting Example: If you select Menus > Option Card Menu > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > Keep - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 21
Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 23 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 22
both printers and MFPs. The Card for IPDS and SCS/TNe includes an http user interface. You can use a browser, such as Microsoft Internet Explorer or Netscape, to remotely configure most SCS/TNe settings. The only requirement is that the printers are attached to a LAN using a Standard Network port - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 23
These new option value settings are saved in the printer and will become active when the next SCS/ all sessions have been disconnected. Click on each TNxxxx Connection Status menu item to check the status of each session. Remote Configuration Using A Browser: How to Use the Browser Interface 25 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 24
TNe Settings. 9 Select one of the TN3270E or saved in the printer and will become active when the next session is started. 12 The browser will then display a confirmation that settings have been submitted. 13 Repeat with the other TN3270E or TN5250E menus as desired. 14 Select the TNe Common menu - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 25
reconnect to the host. 17 Check to be sure that all sessions have been reconnected. Click on each TNxxxx Connection Status menu item to check the status of each session. If all configured sessions have not been established within 90 seconds, you may need to end and reset the sessions at the host and - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 26
version of the MarkNet internal print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For TN3270e Printing Task - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 27
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 29 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 28
to a LAN attached printer. "Mainframe Software" on page 279 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Three sample configurations follow. Sample Configuration number 1: Remote Device - Line definition - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 29
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1), =MTP3816, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1A - Configuring the Host 31 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 30
EJ3270 APPL AUTH=NVPACE,EAS=1,PARSESS=NO, MODETAB=MODETAB2,SESSLIM=YES,DLOGMOD=SCS NOTE: IMLU1; DHW3270; and EJ3270; are the printer devices. SC0TCP01 is a terminal device, and is not needed for printer definitions in this node. Mainframe Installation Setup: Task 1A - Configuring the Host 32 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 31
defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields that are not required, and therefore have been commented out. Mainframe Installation Setup: Task 1A - Configuring the Host 33 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 32
to the host like a normal LU-1 (SCS) printer. Two sample configurations are shown below. Sample Configuration number 1 Remote Device - Line definition In VTAM NCP * LNACC=SDLC PUTYPE=(1,2), NPACOLL=YES Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 34 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 33
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 35 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 34
Guide, Volume 1: Configuration and Routing (document no. SG24-5227-00). The printer with one-to-one mapping of display LUs to printer LUs. This means that a single display LU is mapped to a single printer LU or a display LU group is mapped to a printer LU group. Each group must have the same number - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 35
.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 37 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 36
(PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 38 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 37
in order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways printer connection 1 Choose Insert > 3270 > Application LU (LUA). This opens the 3270 LU Properties box. Mainframe Installation Setup: Task 2B - Configuring - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 38
> TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK| button to finish. Mainframe Installation Setup: Task - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 39
the Standard Network Card menu settings page. b If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot in which the print server is installed. Mainframe Installation Setup: Task 3 -Configuring a Print - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 40
the print server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. Mainframe Installation Setup: Task 3 -Configuring a Print Server 42 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 41
. Select the print server to be used for SCS printing, for example Standard Network. Select Standard Network > Std Network Setup > Network Card > Job Timeout. Scroll down to 0. Touch Submit to save. Option Value Network Job 0 Timeout Description This is the recommended setting and corresponds to - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 42
Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network administrator. Enable DHCP of your DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 44 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 43
Value Comments Your preferred defaults Choose between Do Not Restore *, US-Default, or Non-US-Default 2 Scroll to the desired value. Touch Submit to save one of the factory defaults. 3 Exit the menu by touching Home. Mainframe Installation Setup: Task 4 - Configuring the SCS Settings 45 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 44
the desired value. Touch SelectSubmit to save one of the factory defaults. 3 Exit the menu by pressing touching Home. C. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > SCS OPTIONS > MISC SETTINGS > Euro Support. MISC SETTINGS Option Default Value Euro - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 45
print session 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > SERVER INFO. 2 Configure the SERVER INFO options. Enter or scroll to new values and touch Submit to save your settings. The menu will return to the SERVER INFO menu group within which you scroll to the - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 46
setting values found in the table are described in section "NETWORK SETUP> SERVER INFO Menu: Options Overview" on page 95. SERVER INFO Option Name whether another TCP port number is defined for the Telnet service. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe Emulation 48 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 47
LU Names. Specific Check with your system administrator for the correct setting. The device type must be Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes and touch Submit to save. 4 Exit the menu by touching Home. Mainframe Installation Setup: Task 5 - Configuring - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 48
and change the Connect Status from Print Inactive to another status (there are examples of Connect Status messages on page 92. Mainframe users should continue with Task 6A. SNA Server users should continue with Task 6B. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe Emulation - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 49
one or more of the following actions: 1 Check the TN3270E Connection Status (see page 92) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu >SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 50
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. 3 From the main frame host give the following TCP/IP display - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 51
one or more of the following actions: 1 Check the TN3270E Connection Status (see page 92) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 52
IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 53
of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring the SCS Settings Task 4 - Configuring the SCS/TNe - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 54
. Section "AS/400 and iSeries Software" on page 279 lists host software which supports these protocols. To configure the host check and set the following three system values. System Value QAUTOCFG QAUTORMT Required Value Controls the automatic configuration of devices. Must be set to '1' Sample - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 55
QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto configure devices and writers with the information received from the SCS/TNe Emulation. AS/400 and iSeries Installation Setup: Task 1 - Configuring the Host 57 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 56
Standard Network Card menu settings page. b If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot in which the print server is installed. AS/400 and iSeries Installation Setup: Task 2 - Configuring - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 57
server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 59 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 58
. Select the print server to be used for SCS printing, for example Standard Network. Select Standard Network > Std Network Setup > Network Card > Job Timeout. Scroll down to 0. Touch Submit to save. Option Network Job Timeout Value Description "0" This is the recommended setting and corresponds to - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 59
Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network administrator. Enable DHCP On Server AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 61 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 60
are many other possibilities. IMPORTANT: One set of TN5250e SCS OPTIONS menu values is saved. All four TN5250e connections use the same set of SCS OPTIONS values. A. To select settings for your specific country 1 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > MISC - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 61
, locate Lines Per Page. Scroll to the desired Number and touch Submit to save it. Option Lines Per Page (IDB Option 107) users in the USA 4 (Select other settings within MISC SETTINGS) 5 Exit the MISC SETTINGS menu by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 62
Value Comments 12240 (for Letter). Recommended value for users in (same for Legal). the USA 8 Exit the PAPER SETTINGS menu by touching Back. 9 Change other settings as desired. 10 Exit the menu by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS Settings 64 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 63
Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS Settings - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 64
and touch Submit to save your settings. The menu will return to the SERVER # INFO menu group within which you scroll to the next desired option. When you are finished with all options within SERVER # INFO, touch Home to exit. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 65
section "CONNECTION # > SERVER # INFO Menu: Options Overview" on page 165. Option to specify the specific IP address or the name of the host which the printer will contact to number may be defined for the Telnet service. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 66
Your device name The host will autoconfigure a device and writer with this (up to 10 characters) name if it does not exist. None or own preference Leave this at the factory default if the host is configured will not be auto configured. Contact your system auto configured. Contact your system - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 67
Submit to save. 7 Exit the menu by touching Home. 8 To activate the new settings, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. AS/400 and iSeries Installation Setup: Task 4 - Configuring the - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 68
, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 92. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 70 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 69
through one or more of the following actions: 1 Check the TN5250E Connection Status (see page 162). From the Operator Panel: Display the TN5250E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN5250 SETUP > CONNECTION # SETUP > Connect # Status. Through the http (browser) user - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 70
IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 71
SCS/TNe Cancel About Cancel Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 72
operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only one Print Job shown, as in the example below. To - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 75 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 74
MFP Cancel Job 1 While any job is printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you want to that the job is being deleted. 5 The screen will return to the Home display. Important Configuration Basics: MFP Cancel Job 76 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 75
SCS/TNe Emulation From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 76
Operator Panel: Select Menus > Reports > Menu Settings Page. • Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Reports and choose Device Settings. In the following reference tables - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 77
Menu Options Overview . Option name Values Disconnect Ses Do Not Disconn., Disconnect Ses. Reset TN Session Do Not USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows. Operations - Common Setup: Menu Options Overview 79 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 78
TNe Emulation will attempt to reconnect when the printer is powered Off and On or when Disconnect Ses. should be performed before powering Off the printer. Operator panel text Comments Do Not Disconn. Do Ses. Disconnect ALL active TNe sessions. The printer must be powered Off and On or a - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 79
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. This option disconnects ALL active TNe sessions on TCP/IP - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 80
) and output (ASCII) data. The trace menu option allows you to enable tracing and choose where the trace data should be sent. Because tracing will decrease printing performance, it should only be enabled when needed by service personnel for troubleshooting and service. NOTE: If the SCS/TNe Emulation - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 81
optional parallel port in slot # for trace data output. # is a number representing the slot in which the optional parallel port card is installed. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 82
panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 83
are used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TNE3270E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction 86 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 85
one or more SCS settings are missing from a job, the SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu configured display the text string "[undefined]" and show "[undefined]" on the Menu the current setting. The Menu Settings page shows the been uninstalled. Select one of the currently - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 248 ff.) Operations - TN3270E SETUP: Introduction 88 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 87
NETWORK SETUP Menu: Options Overview The NETWORK SETUP menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the NETWORK SETUP menu. NETWORK SETUP Option name Print Active TN3270 Defaults Connect Status SERVER INFO Values No *, Yes Do Not - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 88
Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active 90 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 89
restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN3270e NETWORK SETUP menu options to factory default settings. All TN sessions will be disconnected. All TN sessions will be reconnected except for the TN3270e session - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 90
in the TN3270E SERVER INFO menu has not been configured. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP). 2 NPA Mode = Off. Solution - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 91
. The device name or resource name requested by the SCS/TNe Emulation is incompatible with the requested device type. Change the device name or device type on the host or check the configuration of the host and of the SCS/TNe Emulation. Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 93 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 92
SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has occurred. Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 94 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 93
to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 *, range: 1 - 32000 [seconds] A description of each SERVER INFO menu option follows. Operations - TN3270E SETUP: NETWORK SETUP> SERVER INFO Menu: Options Overview 95 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact the with the IP Address option. Use the hostname specified with the Hostname option. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Name / IP Address 96 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > IP - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Hostname 98 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 97
. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN Server Port - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 98
to connect to the host or SNA gateway. This Network Setup > Server Info option specifies the LU name assigned to the SCS/TNe Emulation on the host or SNA gateway. Remember also to check the setting of the Device Type option. If a specific LU name is requested, then the name must be defined - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 99
been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU names. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Device Type 101 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 100
be configured to send a keep alive signal. The SCS/TNe Emulation can receive and respond to a Telnet NOP or a Timing Mark keep alive signal. Send a Telnet No Operation as the keep alive signal. Send a Telnet timing mark as the keep alive signal. Operations - TN3270E SETUP: NETWORK SETUP > SERVER - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive signal sent set to None. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep Alive Time 103 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 102
106) and FF Support (IDB Option 5) (page 108). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 133) and Left Margin (IDB Option 103) (page 135). A description of each of the SCS OPTIONS menu item follows. Operations - TN3270E SETUP: SCS OPTIONS Menu: Options Overview 104 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 103
, the orientation is changed to landscape. Option Value No Yes * IDB Value 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:2:EXIT Operations - TN3270E SETUP: SCS OPTIONS > COR/APO Sett (IDB Option 122) 105 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 104
Menu: Options Overview The MISC SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS >MISC SETTINGS Option name FF Support - TN3270E SETUP: SCS Options > MISC SETTINGS Menu: Options Overview 106 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 105
IBM Trn Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range: 1 - 255 6 *, range Translation Normal *, Without '&%' No *, Yes Sub-menu. See SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview (page 129) and Bold On - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 106
FF Support (IDB Option 5) This SCS Options > MISC Settings option defines if a form feed and/or a line feed is Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 108 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 107
. Option Value ASCII Value 45 * ASCII Value [0..255] IDB Value 45 0 - 255 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Non-Print Char (IDB Option 3) 109 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 108
the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are ASCII line to the right. This is done by writing the number of the first option and separating the values for the preceding - TN3270E SETUP: MISC SETTINGS > CSC Characters (IDB Options 8 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 109
list of characters and their values. Option Value : * IDB Value 58 [colon (:)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IDB Delimiter (IDB Option 7) 111 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 110
(IR) reporting to the host. If the option is enabled, IR signals are sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description default: &%IDB_EDIT: OPTION 21:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Use IR (IDB Option 21) 112 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 111
>-M command. Note: Because control codes are suppressed, horizontal/vertical tab and other commands which depend on correct page format will not work correctly. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 113 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 112
default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 114 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 113
suppressed and the auto-NL function is disabled. Control codes can only be sent to the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job IDB_EDIT: OPTION 177:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 115 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 114
Canadian bilingual Canadian French Danish/Norwegian Danish/Norwegian Alternate English, U.K. English, U.S. See note. Finnish/Swedish Finnish/Swedish Alternate French/Azerty 105 International Italian Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 116 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 115
value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:1:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 117 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 116
or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 32:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Skip Blank Page (IDB Option 32) 118 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 117
SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI (IDB Option 100) 119 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 118
SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos (IDB Option 102) 120 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 121 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 122 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 121
LPP (IDB Option 107) This SCS Options > MISC Settings option defines the number of lines per page. NOTE: If the SCS options are restored to non-US 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:64:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPP (IDB Option 107) 123 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 122
167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency (IDB Option 167) 124 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 123
- 57), A - F (ASCII 65 - 70). Also, avoid using one of the characters used as lead in for one of the other CSC commands. This SCS Options > MISC Settings option defines the factory default: &%IDB_EDIT: OPTION 168:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Form Strings (IDB Option 168) 125 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 124
is printed, even invalid data, ie data in the range 40H - FEH. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IBM Trn Code (IDB Option 169 bit 1) 126 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 125
trans- parent handling. 1 User defined transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options 8 & 9) option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Leadin - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 126
(IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E SETUP: MISC SETTINGS > Euro Support (IDB Event 191) 128 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 127
BS (IDB Option 22 bit 2) Bold On Multi BS (IDB Opt. 22 bit 3) Values Yes *, No Yes *, No Yes *, No A description of each BOLD PRINT menu option follows. Operations - TN3270E SETUP: MISC SETTINGS > SCS Options> MISC SETTINGS > BOLD PRINT 129 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 128
on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On CR (IDB Option 22 bit 1) 130 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 129
enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On BS (IDB Option 22 bit 2) 131 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 130
enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On Multi BS (IDB Opt. 22 bit 3) 132 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 131
Portrait *, Landscape, COR Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 133 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 134 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 133
of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Left Margin (IDB Option 103) 135 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 134
(IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:132:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Right Margin (IDB Option 104) 136 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 135
(IDB Option 108) This SCS Options > Paper Settings option defines line number position of the top margin. The line height depends on the setting of to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Top Margin (IDB Option 108) 137 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 136
Option 109) This SCS Options > Paper Settings option defines the line number position of the bottom margin. The line height depends on the setting of set factory default: &%IDB_EDIT: OPTION 109:64:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Bottom Margin (IDB Option 109) 138 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 137
the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from Tray 4 Paper is fed from Tray 5 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 113:1:EXIT Operations - TN3270E SETUP - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 138
) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 1 Orient (IDB Option 123) 140 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 139
) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 2 Orient (IDB Option 124) 141 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 140
) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 3 Orient (IDB Option 125) 142 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 141
) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 4 Orient (IDB Option 126) 143 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 142
) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 5 Orient (IDB Option 127) 144 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 143
value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 90:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray1 Paper Size (IDB Option 90) 145 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 144
value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 91:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray2 Paper Size (IDB Option 91) 146 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 145
value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 92:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray3 Paper Size (IDB Option 92) 147 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 146
value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 93:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray4 Paper Size (IDB Option 93) 148 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 147
value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 94:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray5 Paper Size (IDB Option 94) 149 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 148
: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print SCS3270 Defaults Do - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 149
SCS3270 Hex Dump This Test option enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 150
Print 3270 IDB This Test option prints a tabular report of the current IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 151
option restores the TN3270e SCS OPTIONS setting to their factory default settings. Other printer emulation defaults are unchanged. The restored settings become active on the next SCS job US) English (UK) 64 66 64 66 Letter A4 Operations - TN3270E SETUP: TEST OPTIONS > SCS3270 Defaults 153 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 152
Tray2 Paper Size (IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 153
printing from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TN5250E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 154
Tree diagram of the TN5250E SETUP menu structure. Operations - TN5250E SETUP: Introduction 156 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 155
one or more SCS settings are missing from a job, the SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu configured display the text string "[undefined]" and show "[undefined]" on the Menu the current setting. The Menu Settings page shows the been uninstalled. Select one of the currently - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 156
command is shown at the end of menu options which may be set by remote configuration. Following this are two command lines, one for the User IDB language and another for the Advanced IDB language. These show how to remotely set the menu option to the factory default or how to perform the described - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 157
: Options Overview The SCS/TNe Emulation supports four concurrent TN5250E sessions. Each session has its own unique set of network settings. These are located in the CONNECTION#1 - CONNECTION#4 menus. The SCS OPTIONS (pp.177 ff) menu settings are common to all four sessions. This means that changes - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 158
the activation of the SCS/TNe Emulation for TN5250E communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 159
to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN5250 CONNECTION ## menu options for the current connection to factory default settings. All TN sessions will be disconnected. All TN sessions will be reconnected except for the - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 160
been configured. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 161
Connect # Status: Primary status messages Comments Session Disconnected and Halted All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 162
error Lst Rsp:8922:Negative response received Lst Rsp:8923:Start-up record incorrectly Lst Rsp:8925:Creation of device failed Lst Rsp:8928:Change of device . An exisisting device configuration was not found and the autoconfiguration of virtual devices did not allow any new device descriptions to be - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 163
Connect # Status: Last response messages Lst Rsp:8935:Session rejected Lst the range 0 - 65000 Device # Name [undefined] *, ASCII name with up to 10 characters Keep Alive Type None *, Telnet NOP, Timing Mark Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO Menu: Options Overview 165 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 164
characters. Normal *, Offline, No Reply No *, Yes A description of each SERVER # INFO menu option follows. Name / This Connection# > Server# Info option specifies the kind of IPaddress # with the Hostname # option. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Name / IPaddress # 166 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 165
This Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IP # Address 167 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 166
. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Hostname # 168 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 167
. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server # TN - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 168
associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Device # Name 170 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 169
Mark Comments Do not send keep alive signals. When this setting is selected, the host should be configured to send a keep alive signal. The SCS/TNe Emulation can receive and respond to a Telnet as the keep alive signal. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Type 171 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 170
smaller than the session's inactivity timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires is 1 to 32000 seconds. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Time 172 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 171
default if you do not know the message queue name. Option Value QSYSOPR * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ # Name 173 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 172
the default if you do not know the library name. Option Value *LIBL * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ # Lib 174 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 173
out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the use of IR replies. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IR # Reply 175 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 174
senses automatically if the host has ended the Writer. This may be necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer ends, reconnect, and reconfigure automatically - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 175
The SCS OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. One set of TN5250E SCS OPTIONS menu values are saved. All four TN5250E connections use the same SCS OPTIONS values. The following table lists menu options and sub-menus found under the SCS OPTIONS menu. SCS OPTIONS Option - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 176
208) and Country Code (IDB Option 2) (page 210). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options Overview (page 231) and Left Margin COR (IDB Opt. 78 & 79) (page 232). A description of each SCS OPTIONS menu item follows. Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 178 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 177
2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: OVLCAL OFF:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 179 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 180 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 179
proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which * Use IDB Value 0 1 User IDB parameter OFF ON User IDB command: PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E SETUP: SCS OPTIONS > Prop Font - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 182 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 181
. The command is used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 49 Option Value Off * On IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 183 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 184 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 183
VERMOV : Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 185 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 186 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 185
is incorrectly double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: CTLCODSUP ON:EXIT Advanced - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 186
that these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 189 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 188
Euro Support (IDB Option 139) This SCS Options option controls Euro character printing. If the option is set to Yes, 1144 Spain 284 1145 UK 285 1146 France 297 1147 Multinational 500 1148 Iceland 871 1149 Operations - TN5250E SETUP: SCS OPTIONS > Euro Support (IDB Option 139) 190 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 189
Euro character a font supporting the character also has to be selected and available in the printer. See the Download Font (IDB Option 244) option on page 188 and the Font (IDB Options 242 and 243) option on page 215. Option Value No * Yes IDB Value 0 1 User IDB parameter OFF ON User IDB command - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 190
in the decimal range: 33 - 126 : * (ASCII character 58 [colon]), any single ASCII character in the decimal range: 33 - 126 A description of each CSC CHARACTERS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > SCS OPTIONS > CSC CHARACTERS - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 191
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in Value 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 194 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 193
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in Value 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 196 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 195
IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Delimiter - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 196
PPM Quality Dis (IDB Opt.126) Off *, On, Enable APO COR LSI Reduc (IDB Option 127) 70% *, range: 1 - 100 [%] A description of each COR/APO SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 197
IDB command: ORTDRW 1 : Parameter: DEF, POR, LAN User IDB language to set factory default: &%IDB_EDIT: ORTDRW 1 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 121:1:EXITz Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > Def Page Ori 1 (IDB Option - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 198
IDB command: ORTDRW 2 : Parameter: DEF, POR, LAN User IDB language to set factory default: &%IDB_EDIT: ORTDRW 2 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:1:EXI Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > Def Page Ori 2 (IDB Option 200 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 199
to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape and Portrait (APO) only, or it with the compressed CPI. Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option 123) 201 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 200
command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 201
to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape and Portrait (APO) only, or it can with the compressed CPI. Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option 124) 203 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 202
command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 203
and print all print jobs fulfilling the requirements in computer output reduction mode. Refer to "Appendix D - COR/APO Logic (TN5250e)" on page 287 Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) 205 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 204
IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) 206 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 205
LINSPRED : Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default: &%IDB_EDIT: LINSPRED 70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:70:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR LSI Reduc (IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 206
, 1653, 2103 10 CPI *, 5 CPI, 12 CPI, 15 CPI, 16.7 CPI 80 *, range: 1 - 254 1 *, range: 1 - 255 1 *, range: 1 - 255 6 LPI *, 3 LPI, 4 LPI, 8 LPI, 9 LPI Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS Menu: Options Overview 208 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 207
2, Output Bin 3 Prtr Setting *, Simplex, Duplex, Duplex (Tumble) ASCII Value 45, any single ASCII character in the decimal range: 0 - 255 A description of each MISC SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS Menu: Options Overview 209 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 208
System 36 and 38, and applications migrated from these systems. The codes other than International country specific characters replace selected characters. Option 6 7 8 9 10 11 12 User IDB parameter 0 1 2 3 4 5 6 7 8 9 10 11 12 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 209
Value 13 14 15 User IDB parameter 13 14 15 User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 210
by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 280 Jap/Eng 281 Portugal 282 Spain 284 Eng (UK) 285 France 297 IDB Values (Option 240 and 241) User IDB parameter 37 + 0 37 3 + 1 259 17 + 1 273 18 + 1 274 19 + 1 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 211
and 241) User IDB parameter OCR 340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this 4 1148 Iceland 1149 125 + 4 1149 User IDB command: DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 214 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 213
system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option Value ( 12 110 Let.Got. Bld 12 111 Pres. Bold 12 112 Pres. It 12 IDB Value (Option 242 and 243) User IDB parameter 3 + 0 3 11 + 0 11 18 + 0 18 39 + 0 39 40 + 0 40 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 214
Son.Ser. 7 1051 Son.Ser. 10 1053 Son.Ser.Bld 10 IDB Value (Option 242 and 243) User IDB parameter 155 + 0 155 159 + 0 159 160 + 0 160 163 + 0 163 175 + 239 + 2 751 27 + 4 1051 29 + 4 1053 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 216 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 215
: DEFFNT : Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 242:11: OPTION 243:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 216
parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > CPI - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 217
IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:80:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Max Print Pos (IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 218
IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Left Margin (IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 219
IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Right Margin (IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 220
SCS Options > Misc Settings option selects the number of 105) lines per inch (LPI). Option Value 3 LPI 4 LPI 6 LPI * 8 LPI 9 LPI IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 221
Per Page This SCS Options > Misc Settings option defines the number of (IDB Option 107) lines per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 222
IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Top Margin (IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 223
contain a string which selects a specific tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 224
IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory default: &%IDB_EDIT: DEFFRMSEL DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 114:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Forms Media (IDB Option 114 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 225
IDB command: DEFDSTDRW : Parameter: DEF, 1, 2, 3 User IDB language to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 115:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Output Bin (IDB Option 115) 227 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 226
or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB parameter DEF SIM DUP TUM User IDB command: DEFSIMDUP : Parameter: DEF, SIM, DUP, TUM - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 229 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 228
when the host sends an unprintable character or a character not supported by the SCS/TNe Emulation. Refer to "Appendix B - User IDB language to set factory default: &%IDB_EDIT: UNPCHR /2D:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN5250E SETUP - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 229
& 85) Values 634 *, range: 0 - 2880 0 *, range: 0 - 2880 0 *, range: 0 - 2880 147 *, range: 0 - 2880 16848 *, range: 1 - 65535 11908 *, range: 1 - 65535 A description of each PAPER SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 231 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 230
(1/1440 inch) IDB Values (Option 78 and 79) User IDB parameter 634 * [0..2880] 122 + 2 0.44 User IDB command: LFTOFFCOR : Parameter 1: 00 .. 2.009 or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44: - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 231
× 1440) - (256 × Value stored in option 79) Round off to nearest whole number. The values stored in option 78 and 79 for a left margin offset of 0.440 inch to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 232
Value (1/1440 inch) IDB Values (Option 80 and 81) User IDB parameter 0 * [0..2880] 0 + 0 0.00 User IDB command: TOPOFFCOR : Parameter 1: .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 233
inch × 1440) - (256 × Value stored in option 81) Round off to nearest whole number. The values stored in option 80 and 81 for a top margin offset of 1 inch centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 234
(1/1440 inch) IDB Values (Option 86 and 87) User IDB parameter 0 * [0..2880] 0 + 0 0 User IDB command: LFTOFFLAN : Parameter 00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 235
1440) - (256 × Value stored in option 87) Round off to nearest whole number. The values stored in option 86 and 87 for a left margin offset in Landscape to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 & - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 236
(1/1440 inch) IDB Values (Option 88 and 89) User IDB parameter 147 * [0..2880] 147 + 0 0.10 User IDB command: TOPOFFLAN : Parameter 00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 237
) - (256 × Value stored in option 89) Round off to nearest whole number. The values stored in option 88 and 89 for a top margin offset in can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt. 88 & - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 238
29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 240 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 239
00 .. 115.60] with 2 decimals User IDB language to set factory default: &% below. 83: -L---e---n----g---t--h-----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 82: (Length inch × 1440 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 240
in cm 21.00 21.59 21.59 18.42 Width in inch. 8.27 8.50 8.50 7.25 Option value 11908 12240 12240 10440 User IDB command: PAGWDT : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 242 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 241
00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT . 85: W------i-d----t-h------i-n---c---h-----×-----1---4---4----0-- Reduce to nearest whole number. 256 84: (Width inch × 1440 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 242
: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print SCS5250 Defaults Do - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 243
SCS5250 Hex Dump This Test option enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 244
listing the current IDB settings. Print this report when asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB . Print the IDB settings. User IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN5250E SETUP: TEST OPTIONS > Print 5250 IDB 246 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 245
restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu settings. Operations - TN5250E SETUP: TEST OPTIONS > SCS5250 Defaults 247 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 246
for adapting the SCS/TNe Emulation to existing applications. The SCS options are programmed using the guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users can use the Advanced IDB Language to access and configure - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 247
to use. However, the User IDB Language is only available for working on approximately 20 of the most common IDB options. Working with the other options requires the use of the Advanced IDB Language. The IDB languages are to be used during initial setup or re-configuration of the SCS/TNe settings - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 248
the Control Panel" on page 10 ff. "Operations Reference - TN3270E SETUP" on page 85 and "Operations Reference - TN5250E SETUP" on page 155. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 249
one of the IDB command languages, the configuration data is sent as text to the SCS/TNe Emulation. Rules for configuration data 1 Send the data to the SCS/TNe Emulation device syntax or range errors are ignored. If the SCS/TNe Emulation prints out the commands, or prints out error messages, it could - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 250
mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings are active on the next SCS job. All configuration options must be separated by a colon. Line feed, form feed etc. should be avoided, but are accepted in some cases. IDB Basics - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 251
Programming examples Advanced IDB (TN3270E + TN5250E) User IDB (TN5250E) Valid &%IDB_EDIT: &%IDB_EDIT: - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 252
on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups. IDB Basics: IDB Configuration File Management 254 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 253
binary mode. This is necessary as data is transferred in binary mode. binary 4 Retrieve the IDB configuration file. get tn3270e.idb c:\tn3270e.idb (TN3270E users) get tn5250e.idb c:\tn5250e.idb (TN5250E users) This stores the file on the PC in the root directory c:. IDB Basics: Retrieving the IDB - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 256 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 255
is DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File TN3270E P01-xxxx.zip TN5250E P02-xxxx.zip Comments This contains the 3270 IDB configuration file editor program, also known as IDB.exe. This contains - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 256
Storing the IDB Configuration File When the IDB configuration file has been edited it can be downloaded to the SCS/TNe Emulation. The download file name is fixed. Downloading a file with a different name will result in an unreadable printout. No IDB settings will be changed. The procedure below - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 259 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 258
Commands Using IDB Introduction The IDB commands described here provide additional commands for controlling the printer. This chapter presents the syntax for creating these commands, which must be sent from the AS/400 or iSeries in order to be recognized, i.e. included - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 259
Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use commas to separate. 12,34 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 260
, it is possible to set up four strings of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 261
> : POWON DEL : Parameter: 1 - 4 Example: POWON 3 "Power initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 263 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 262
8. The events 74 - 78 require programming before they can be used to select a specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 263
on page 227. The command corresponds to event 59 - 61. Command: DSTDRW : DSTDRW DEL : Delete command Parameter: 1 - 3 Drawer number Example: DSTDRW 2 /1B,"&l2G": DSTDRW DEL 1: PCL command string for setting dest.drawer 2 to bin 1 Delete command string for dest.drawer - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 264
: SLTMED DEL : Delete command Parameter: PAP ENV Select paper media Select envelope media Example: SLTMED PAP "Paper media": SLTMED DEL ENV: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper / Envelope Media 266 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 265
This is triggered by the AS/400 or iSeries command SPSU (Set Print Setup) when a certain kind of paper feed is selected. The command corresponds to feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 267
used. This can be used to switch to a symbol character set or a special "symbol font" if it has been downloaded to the printer. It is also possible to select another font in the printer, e.g. a special mathematical font. The COD259 BEF command is executed each time there is a switch to code page 259 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 270 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 269
to event 55 - 56. Command: OVLDRW : OVLDRW DEL : Delete command Parameter: 1 - 2 Drawer number Example: OVLDRW 1 /1B,"&f3Y",/1B,"&f2X":PCL string for calling macro no. 3 OVLDRW DEL 1: TN5250e Printer Commands Using IDB: Miscellaneous > Overlay Command 271 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 272 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 271
selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 273 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 272
for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or Status printout subtitle Hexdump printout subtitle Example: SUBTIT IDB /0A,/0D,"SCS Printer": SUBTIT HEX "Setup for test 05-18-99": SUBTIT DEL HEX: TN5250e Printer - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 273
DEL: Delete command Example: MOVUPRLIN /1B,"&l0E",/1B,"&a0V":PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to Uppermost Line 275 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 276 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 275
AS/400, iSeries, or Mainframe host software and this option, the printer can emulate an IBM 3287/3812 in LU1 mode (3270 SCS) or an IBM 3812-01 (5250 SCS) printer. One TN3270e connection is supported. Up to four TN5250e connections are supported. The SCS/TNe Emulation autodetects installed features - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 278 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 277
Server for VTAM V4R4 or greater AS/400 and iSeries Software • Application System AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms 279 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 278
: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 279
Features List: 5250 SCS Features supported are dependent upon host software for selection and use. • SCS and SCS/DCA L2 transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC character conversion • SCS command conversion • Text - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 280
Appendix B - ASCII Character Table Printable The table shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 282
Appendix C Special TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 283
List of Larger numbers indicate higher precedence. Commands Precedence Command Comments 5 HEXDUMP Enter hex-dump mode (small format) 5 HEXDUMP_FULL Enter hex-dump mode (large format) 5 IDB_EDIT - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 10) if necessary. Appendix - TN3270e IDB Commands: List of Commands 286 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 285
TN5250e) can rotate the printout from portrait to landscape based on menu option settings. The distinction is between control of text, orientated . The focus of this discussion is on how the printer automatic controls operate, as the user does not always have the possibility of defining whether a - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 286
that no STO commands are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 287
PAGLNG = A4 and PAGWDT = A4 2 If the page format stated in the FCB is within (or equal to) the page size settings of the PAGLNG and PAGWDT option settings, the page size is "valid". In that case the printout will be in landscape provided the page length is smaller than the width, otherwise it will - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 288
sizes are compressed to the nearest smaller font. 4 Most program applications normally have a set of standard values for page length, characters per line etc. The user might have few or no possibilities off changing, e.g., the number of characters per line, which is normally set to 132 characters - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 289
file (CRTPRTF). Please consult your AS/400 or iSeries manuals for information on this subject. Defining the printer file to make the COR is normally done in connection with IPDS page printers as these printers do not support the APO/COR function. If the APO/COR is disabled (CORDRW 1/2 = OFF), the - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 292 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 293 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 292
Appendix E Special TN5250e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 293
List of Larger numbers indicate higher precedence. Commands Precedence Command 5 IDB_EDIT 5 IDB_PRINT 5 IDB_PRINT_FULL 5 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 294
the IBM font IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR fonts are made, it will print out a message and a font table status sheet. This status sheet has the IBM IDs indicated in the second column. To free font - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 295
), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded operator panel using the Download Font (IDB Option 244) option. See page 188. Appendix - SCS TN5250eFont Table: - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 296
FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the substitution font IDs set by the SETSUBFNT command. Appendix - SCS TN5250eFont Table: The "Font - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 298
The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM 154 - 200). The spacing command should only be used when using downloaded proportional fonts with the correct character spacing. N This value is - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 299
causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded proportional spaced - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 301
font table. The first 7 font positions listed in the status printout (&%IDB_STATUS) represent the substitution fonts for the following areas 3 7 4 5 6 2 Command: SETSUBFNT : NOTE: The font number must be a font number already present in the font table. Appendix - SCS TN5250eFont - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 302
ID 67, but all font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 304 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 303
User's Guide Fourth Edition July 2009, Rev 004. The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 304
or both. Intelligent Printer Data Stream and IPDS are trademarks or registered trademarks of Ricoh Co., Ltd in the United States, other countries, or both. Lexmark and Lexmark with diamond design, trademarks are the property of their respective owners. Trademarks: SCS/TNe Emulation User's Guide 306 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 305
User's Guide Getting Started ...1 SCS/TNe in a LAN environment ...1 Documentation Overview ...1 Equipment Requirements and Specifications ...2 Support ...4 Customer Support ...4 Important Configuration Basics ...5 Introduction ...5 What are "IDB Options", "IDB events etc.? ...6 Setup Options - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 306
the Host Connection ...69 SCS/TNe Cancel ...71 About Cancel Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset TN Session ...79 SCS Debug Trace ...80 : 306 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 307
: Options Overview ...87 Print Active ...88 TN3270 Defaults ...89 Connect Status ...90 NETWORK SETUP> SERVER INFO Menu: Options Overview 93 Name / IP Address ...94 IP Address ...95 Hostname ...96 TN Server Port ...97 LU Name ...98 Device Type ...99 Keep Alive Type ...100 Keep Alive Time ...101 SCS - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 308
IDB Option 168) ...123 IBM Trn Code (IDB Option 169 bit 1) ...124 Leadin Sequence (IDB Option 169 bit2) ...125 Euro Support (IDB Event 191) ...126 SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview 127 Bold On CR (IDB Option 22 bit 1) ...128 Bold On BS (IDB Option 22 bit 2) ...129 Bold - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 309
SETUP 153 Introduction ...153 CONNECTION # Menu: Options Overview ...157 Print # Active ...158 TN5250## Default ...159 Connect # Status ...160 CONNECTION # > SERVER # INFO Menu: Options Overview 163 Name / IPaddress # ...164 IP # Address ...165 Hostname # ...166 Server # TN Port ...167 Device - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 310
Option 114) ...224 Output Bin (IDB Option 115) ...225 Simplex/Duplex (IDB Option 116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 229 Left Margin COR (IDB Opt. 78 & 79) ...230 Top Margin COR (IDB Opt. 80 & 81) ...232 Left Margin Lan (IDB Opt. 86 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 311
References ...248 IDB Languages Usage ...249 IDB Configuration File Management ...252 Retrieving the IDB Configuration File ...253 Editing the IDB Configuration File ...255 Storing the IDB Configuration File ...256 Additional TN5250e Printer Commands Using IDB 258 Introduction ...258 Input Data - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 312
Specifications, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280 - Lexmark X651DE | SCS/TNe Emulation User's Guide - Page 313
SCS/TNe Emulation User's Guide ...303 Trademarks ...304 ...304 Table of Contents ...305 : 313
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 277
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA