LiftMaster 8160 8160 Installation Manual - Page 36

Remote Control, To Erase the Memory, TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN

Get LiftMaster 8160 PDF manuals and user guides View all LiftMaster 8160 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Operation Remote Control Your remote control has been programmed at the factory to operate with your garage door opener. Older LiftMaster remote controls are NOT compatible, see page 41 for compatible accessories. Programming can be done through the door control or the learn button the garage door opener. To program additional accessories refer to the instructions provided with the accessory or visit LiftMaster.com. If your vehicle is equipped with a Homelink®, you may require an external adapter depending on the make, model, and year of your vehicle. Visit www.homelink.com for additional information. TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN USING THE DOOR CONTROL 1. Press the LEARN button on the door control twice. The Command LED will blink. 2. Remote Control: Press the button on the remote control that you wish to operate your garage door. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button. The garage door opener lights will flash (or two clicks will be heard) and the Command LED will stop blinking when the code has been programmed. Repeat the steps above for programming additional remote controls or keyless entry devices. If programming is unsuccessful, program the remote using the learn button. PROGRAM USING THE GARAGE DOOR OPENER 1. Press and release the LEARN Button on the garage door opener. 2. Press and hold the button on the remote control that you wish to use. Release the button when the garage door opener lights blink or two clicks are heard. 1 2 "cli"cckl"ick" LEARN Button LEARN LED To Erase the Memory ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1. Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use. ERASE ALL DEVICES (Including MyQ® enabled accessories) 1. Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds). 2. Immediately press and hold the LEARN button again until the learn LED goes out. All codes are now erased. Reprogram any accessory you wish to use. 1 LEARN button Command LED 2 OR 4GHI 5 6 JKL MNO 7 8 9 PRS TUV WXY * * 0 QZ # 0 QZ # ENTER ENTER ???? PIN 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
36
Operation
Remote Control
Your remote control has been programmed at the factory to operate with your
garage door opener.
Older LiftMaster remote controls are NOT compatible, see page 41 for compatible
accessories. Programming can be done through the door control or the learn button the
garage door opener. To program additional accessories refer to the instructions provided
with the accessory or visit LiftMaster.com. If your vehicle is equipped with a Homelink
®
,
you may require an external adapter depending on the make, model, and year of your
vehicle. Visit www.homelink.com for additional information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE DOOR CONTROL
1.
Press the LEARN button on the door control
twice
. The Command LED will blink.
2.
Remote Control:
Press the button on the remote control that you wish to operate your garage
door.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless
entry keypad. Then press the ENTER button.
The garage door opener lights will flash (or two clicks will be heard) and the Command
LED will stop blinking when the code has been programmed. Repeat the steps above for
programming additional remote controls or keyless entry devices. If programming is
unsuccessful, program the remote using the learn button.
1
OR
PIN
?
?
?
?
4
5
7
8
9
0
*
#
ENTER
0
QZ
*
#
ENTER
6
2
LEARN button
Command LED
PROGRAM USING THE GARAGE DOOR OPENER
1.
Press and release the LEARN Button on the garage door opener.
2.
Press and hold the button on the remote control that you wish to use. Release
the button when the garage door opener lights blink or two clicks are heard.
LEARN LED
LEARN
Button
“click”
“click”
1
2
To Erase the Memory
ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES
1.
Press and hold the LEARN button on garage door opener until the learn LED goes
out (approximately 6 seconds). All remote control and keyless entry codes are
now erased. Reprogram any accessory you wish to use.
ERASE ALL DEVICES (Including MyQ
®
enabled accessories)
1.
Press and hold the LEARN button on garage door opener until the learn LED goes
out (approximately 6 seconds).
2.
Immediately press and hold the LEARN button again until the learn LED goes out.
All codes are now erased. Reprogram any accessory you wish to use.