Linksys WRE54G Cisco WAP54GP Wireless-G Access Point with Power Over Ethernet - Page 35

SNMP Trusted Host, Get Community - password

Get Linksys WRE54G - Wireless-G Range Expander Repeater PDF manuals and user guides
UPC - 745883559046
View all Linksys WRE54G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Wireless-G Access Point with Power Over Ethernet Device Name. Enter the name you wish to give to the Access Point. Location. Enter the location of the Access Point. Get Community. Enter the password that allows read-only access to the Access Point's SNMP information. The default is public. Set Community. Enter the password that allows read/write access to the Access Point's SNMP information. The default is private. SNMP Trap-Community. Enter the password required by the remote host computer that will receive trap messages or notices sent by the Access Point. SNMP Trusted Host. You can restrict access to the Access Point's SNMP information by IP address. Enter the IP address in the field provided. If this field is left blank, then access is permitted from any IP address. SNMP Trap-Destination. Enter the IP address of the remote host computer that will receive the trap messages. Change these settings as described here and click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Help information is displayed on the right-hand side of the screen, and click More for additional details. Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet 29 The Administration - Management Tab

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
29
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Administration - Management Tab
Wireless-G Access Point with Power Over Ethernet
Device Name
. Enter the name you wish to give to the Access Point.
Location
. Enter the location of the Access Point.
Get Community
. Enter the password that allows read-only access to the Access Point’s SNMP information. The
default is
public
.
Set Community
. Enter the password that allows read/write access to the Access Point’s SNMP information. The
default is
private
.
SNMP Trap-Community
. Enter the password required by the remote host computer that will receive trap
messages or notices sent by the Access Point.
SNMP Trusted Host
. You can restrict access to the Access Point’s SNMP information by IP address. Enter the IP
address in the field provided. If this field is left blank, then access is permitted from any IP address.
SNMP Trap-Destination
. Enter the IP address of the remote host computer that will receive the trap messages.
Change these settings as described here and click
Save Settings
to apply your changes, or click
Cancel
Changes
to cancel your changes. Help information is displayed on the right-hand side of the screen, and click
More
for additional details.