Lowrance Elite-12 Ti Installation Manual EN - Page 41

Fuel Level, Set to full, Calibrate, actual amount used, Fuel K-Value

Get Lowrance Elite-12 Ti PDF manuals and user guides View all Lowrance Elite-12 Ti manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

1. Start with a full tank and run the engine as it would normally be operated. 2. After at least several liters (a few gallons) have been used, the tank should be fully refilled, and the Set to full option selected. 3. Select the Calibrate option. 4. Set the actual amount used based on amount of fuel added to the tank. 5. Select OK to save settings. The Fuel K-Value should now show a new value. Ú Note: To calibrate multiple engines repeat the steps above, one engine at a time. Alternatively, run all engines simultaneously, and divide the Actual amount used by the number of engines. This assumes reasonably even fuel consumption on all engines. Ú Note: The Calibrate option is only available when Set to full is selected, and a Fuel Flow is connected and set up as a source. Ú Note: A maximum of 8 engines is supported using Fuel Flow sensors. Fuel Level Fuel level configuration is not available on the ELITE-5Ti. With the use of a Navico Fluid Level device connected to a suitable tank level sensor, it is possible to measure the amount of fuel remaining in any equipped tank. The number of tanks must be set in Vessel Setup dialog, initiated from the Fuel setting options page, to allow discrete tank assignment of the Fluid Level devices. Software Setup | ELITE Ti Installation Manual 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
1.
Start with a full tank and run the engine as it would normally be
operated.
2.
After at least several liters (a few gallons) have been used, the
tank should be fully refilled, and the
Set to full
option selected.
3.
Select the
Calibrate
option.
4.
Set the
actual amount used
based on amount of fuel added
to the tank.
5.
Select
OK
to save settings. The
Fuel K-Value
should now show
a new value.
Ú
Note:
To calibrate multiple engines repeat the steps above, one
engine at a time. Alternatively, run all engines simultaneously,
and divide the
Actual amount used
by the number of engines. This
assumes reasonably even fuel consumption on all engines.
Ú
Note:
The
Calibrate
option is only available when
Set to full
is
selected, and a Fuel Flow is connected and set up as a source.
Ú
Note:
A maximum of 8 engines is supported using Fuel Flow
sensors.
Fuel Level
Fuel level configuration is not available on the ELITE-5Ti.
With the use of a Navico Fluid Level device connected to a suitable
tank level sensor, it is possible to measure the amount of fuel
remaining in any equipped tank. The number of tanks must be set
in Vessel Setup dialog, initiated from the Fuel setting options page,
to allow discrete tank assignment of the Fluid Level devices.
Software Setup
| ELITE Ti Installation Manual
41