Makita BMR100W Owners Manual - Page 8
Snooze function, Sleep function, Display illumination, Setting tuning step, Change Stereo to Mono, - battery
View all Makita BMR100W manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
1. The HWS buzzer alarm can be set either radio is on or off. 2. Press and release the HWS buzzer alarm button , the symbol will flash. 3. During the symbol flashes, long pressing the button for more than 2 seconds followed by a beep and display Hour digit will flash. 4. Rotate Tuning Control to select required alarm hour, then press time set button again. The minute digit will then flash. 5. Rotate Tuning Control to select required alarm minute, the press time set button again to complete HWS buzzer alarm setting. 6. Press and hold down buzzer alarm button for more than 2 seconds followed by a beep to switch on or off the HWS buzzer alarm. Display will appear when buzzer alarm has been set. Snooze function 1. Whilst the alarm is activated, pressing any buttons except the Power Button will activate the snooze function. The radio or HWS buzzer alarm will be silenced with interval of 5 minutes. 2. The display will flash both the snooze symbol and the alarm symbol. The snooze function can be repeatedly during one hour that the alarms are active. Sleep function The sleep timer will automatically switched off the radio after a preset time has elapsed. 1. Press and continue to hold down the Power button for more than 2 seconds, followed by a beep tone, the display will cycle through the available sleep times in the order 60-45-30-15-120-90-60. Release the Power button when the required sleep time appears in the display. The symbol will appear in the display and the radio will play the last station selected. 2. To cancel the sleep function, press the Power button. The Symbol will disappear and radio is off. Display illumination Press any buttons or rotate tuning/volume control will illuminate the LCD display for approx. 15 seconds. During scanning stations and alarm activated, will also automatically illuminate the display. Setting tuning step Tuning steps on some countries are different from where you purchase the radio. If you buy the radio in Europe and intend to use in Northern America or some Southern American countries, you may have to adjust tuning step so the radio may continue to serve you well. While radio is switched off, long pressing Step/Band button for more than 2 seconds will first show current FM tuning step. 8 Continue pressing Step/Band button for approx. another 5 seconds until display FM and 50 kHz (tuning step) flashing followed by a beep. By rotating the Tuning control, you may adjust to 100 kHz per tuning step. After FM tuning step is reset, pressing Step/Band button again, display will show AM (MW) and flash 9 kHz. By rotating Tuning control, you may adjust to 10 kHz per tuning step. Complete the setting by pressing Step/Band button. Change Stereo to Mono When the stereo FM station reception is weak, you can improve it by pressing Mono button for 2 seconds. The sound is no longer in stereo and stereo indicator disappears. Headphone socket A 3.5 mm headphone socket located in front of your radio is provided for use with either headphones or an hairpiece. Inserting a plug automatically mutes the internal speaker. Specifications: Power Requirements AC power adaptor DC12V 700mA, center pin positive Battery UM-3 (AA size) x 2 for back up Cluster battery: 9.6 - 18V Slide battery: 9.6 - 24 V Frequency coverage: FM 87.50 - 108 MHz AM 520 - 1710 kHz (10 kHz/step) Circuit feature Loudspeaker 3 inches 8 ohm Output Power 9.6V: 0.8 W x 2, 12V: 1.2 W x 2 14.4V: 2W x 2, 18V: 3W x 2 24V: 5W x 2 Headphone socket 3.5 mm dia. Antenna system FM: soft bended rod antenna AM: bar antenna Dimension (W x H x D) in mm: 263 x 305 x 166 Weight 4.2kg (without battery)