Makita LC1230 Owners Manual

Makita LC1230 Manual

Get Makita LC1230 PDF manuals and user guides View all Makita LC1230 manuals
Add to My Manuals
Save this manual to your list of manuals

Makita LC1230 manual content summary:

  • Makita LC1230 | Owners Manual - Page 1
    A A. A A.. Metal Cutting Saw 305 mm (12") MODEL LC1230 INSTRUCTION MANUAL O a DOUBLE INSULATION SPECIFICATIONS Blade diameter Hole (arbor) diameter No load speed (RPM) Dimensions (L x W x Hl Net weight Cutting capacity Workpiece shape 305 mm (12") 25.4 mm (1") 1 300 516 mm x 306 mm 603 mm (20
  • Makita LC1230 | Owners Manual - Page 2
    . It's safer than using your hand and it frees both hands to operate tool. 13. DON'T OVERREACH. Keep proper footing and balance at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 2
  • Makita LC1230 | Owners Manual - Page 3
    POWER OFF. Don't leave tool until it comes to a complete stop. 23. When servicing use only identical replacement parts. 24. POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only
  • Makita LC1230 | Owners Manual - Page 4
    1. Wear eye protection. 2. Do not operate saw without guards in place. 3. Don't use the tool in the presence of flammable liquids or gases. 4. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 5. Use only flanges specified for this tool
  • Makita LC1230 | Owners Manual - Page 5
    pipe or workpieces which cannot be secured firmly with the vise. The piece cut off may be caught by the blade, causing dangerous scattering of chips and/or damage to the carbide-tips. Possible serious injury may result. 26. Unplug tool before changing blade or servicing. SAVE THESE INSTRUCTIONS. 5
  • Makita LC1230 | Owners Manual - Page 6
    Socket wrench The socket wrench is stored on the left side of the tool base. When using the socket wrench, pull it out of the wrench holder. After using the socket wrench, return it to the wrench holder. Base Positioning the tool When the tool is shipped from the factory, the handle is
  • Makita LC1230 | Owners Manual - Page 7
    saw blade CAUTION: •Always be sure that the tool is switched off and unplugged before removing or installing the blade. •When mounting the blade, make sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case. •Use only the Makita
  • Makita LC1230 | Owners Manual - Page 8
    sure that the safety cover moves properly. Carbide•tipped saw blade Hex bolt Spindle Inner flange 6 Outer flan e Setting for desired cutting angle CAUTION: Always tighten the hex bolt securely after changing the cutting angle. To change the cutting angle, loosen the lever. Move the vise stop so
  • Makita LC1230 | Owners Manual - Page 9
    supported using the tool, remove blade, workpiece or cutting chips immediately after operation; they may be extremely hot and could burn your skin. •If the blade stops during operation, makes an odd noise or begins to vibrate, switch off the tool immediately. Replace cracked or damaged blade
  • Makita LC1230 | Owners Manual - Page 10
    block up against the workpiece as shown in figure D so that the saw blade will enter area A at an angle. This will help to extend the saw blade life. The allowable cutting dimensions are reduced when a wooden block is used. Use a wooden block whose dimensions are equivalent to the maximum allowable
  • Makita LC1230 | Owners Manual - Page 11
    as shown in figure H and figure I so that the saw blade will enter areas A and B at an angle. This will help to minimize the shortening of the saw blade life. The allowable cutting dimensions are reduced when a wooden block is used. Use a wooden block whose dimensions are equivalent to the maximum
  • Makita LC1230 | Owners Manual - Page 12
    Dust collection CAUTION: Do not touch any part of the dust box except its handle immediately after operation; it may be extremely hot and could burn your skin. This tool is equipped with the dust box to collect dust and cut chips. When the dust box is full, hold the handle of the
  • Makita LC1230 | Owners Manual - Page 13
    Replacing saw blade Continuing to use a dull and worn blade may cause motor overload and decreased cutting efficiency. Replace with a new blade as soon as it is no longer effective. Replacing be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts,. 13
  • Makita LC1230 | Owners Manual - Page 14
    /64" 3/64" - 13/64" 5/32" or more 3/84" - 13/64" 1/8" - 5/32" INA . Not applicable) CAUTION: • Always use carbide-tipped saw blades appropriate for your job. Do not cut aluminum, wood, plastics, concrete, tiles, etc. • Carbide-tipped saw blades for metal cutting saw are not to be re-sharpened. 14
  • Makita LC1230 | Owners Manual - Page 15
    305 mm (12") METAL CUTTING SAW Model LC1230 June-7-'99 US 7,1" 19 20 21 25 23 34 35 E15 GLE17 El3 E08 ,L E: 91..E07 EIO E12 E16 E06 AI E05 Ell E14 10
  • Makita LC1230 | Owners Manual - Page 16
    100 102 101 110 69 70 71 4- 72 76 - 73 74 103 -- 104 99 78- 1 79 1 80 109 0--98 81 84 82 83 86 87 85 108 88 89 90 91 115 92-0'-0 9 g-94 96 97 95 114 Note: The switch and other part configurations may differ from country to country. 16
  • Makita LC1230 | Owners Manual - Page 17
    LC1230 ITEM NO. NO. USED DESCRIPTION ITEM NO. NO. USED Guide Screw M6 Ring 20 Ball Bearing 6204DDW Key 5 Spindle Inner Flange 70 Outer Flange 70 Hex. Flange Heed Bolt M10x20 Blade Case Set With Item 561 Pin 6-7' Makita Note: The switch and other part specifications may differ from country Support
  • Makita LC1230 | Owners Manual - Page 18
    18
  • Makita LC1230 | Owners Manual - Page 19
    19
  • Makita LC1230 | Owners Manual - Page 20
    sanding, sawing, Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
A
A.
A
A..
Metal
Cutting
Saw
305
mm
(12")
MODEL
LC1230
INSTRUCTION
MANUAL
O
a
DOUBLE
INSULATION
SPECIFICATIONS
Blade
diameter
305
mm
(12")
Hole
(arbor)
diameter
25.4
mm
(1")
No
load
speed
(RPM)
1
300
Dimensions
(L
x
W
x
Hl
516
mm
x
306
mm
603
mm
(20-1/3"
x
12"
x
23-5/8")
Net
weight
19.0
kg
(41.8
lbs)
Cutting
capacity
Workpiece
shape
Cutting
angle
OA
Axe
r
A
1
.--
B
--b-
90°
115
mm
(4-1/2")
75
mm
x
150
mm
(2-15/16"
x
5-7/8")
100
mm
x
100
mm
(3-15/16"
x
3-15/16")
45°
90
mm
(3-1/2")
85
mm
x
85
mm
(3-5/16"
x
3-5116")
•
Manufacturer
reserves
the
right
to
change
specifications
without
notice.
•Note:
Specifications
may
differ
from
country
to
country.
WARNING:
For
your
personal
safety,
READ
and
UNDERSTAND
before
using.
SAVE
THESE
INSTRUCTIONS
FOR
FUTURE
REFERENCE.