Marantz SR-19EX Marantz AV Receiver IR Remote Code List - Page 23
Other, Functions
View all Marantz SR-19EX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
OTHER FUNCTIONS MULTI ROOM SELECTOR The Multi Room Selector is a function which allows you to listen to the same or a different source in a room other than the room in which the SR-19 is located. To use this function, a multi room remote unit and remote control signal receiver available from your Marantz dealer are necessary. The operations possible with the multi room function are explained briefly below. For details, refer to the instruction manual supplied with the multi room remote control unit and receiver. MULTI ROOM SELECTOR OPERATION 1, Press the MULTI button 0. The unit enters multi room mode and the display indicates "SEL SOURCE" and flashes the "MULTI" indicator for approx. 10 seconds. In this time, you can select the input source by turning the INPUT SELECTOR knob (D. 2. Then, the display indicates "MULTI VOL" "VOLUME xx dB" for approx. 5 seconds. At this time, you can set the volume level of the multi room. MULTI ROOM SELECTOR OPERATION (USING THE MULTI ROOM REMOTE CONTROL UNIT) 1. Press the MULTI button, the POWER ON button, or select the desired source on multi room remote control unit from the MULTI ROOM. Any of these operations will put the SR-19 into multi room mode and "MULTI" will light in the display. 2. Press the VOL.UP or VOL.DOWN button on the multi room remote control unit to set the desired sound volume. 3. In multi room mode, the multi room remote control unit can be used in the multi room to operate the following functions. You can select a tuner preset channel and tuning up or down, and direct selection. And you can control the CD player LD player, DVD player and tape deck connected to the SR-19. Caution: Multi room mode can be selected when the SR-19 POWER switch is turned on. If the main room is active (not standby mode), you cannot select the frequency band except the band of the main room. For example; if the FM band is selected in the main room, you cannot select the AM band in the multi room. The operating procedure for this is the same as the Multi-room operations using the remote unit. TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV IN jack to control the power (ON/OFF) to the SR-19. AUTO POWER ON 1. Be sure TV auto mode is on. (Refer page 9 : System Setup 2/2 ) 2. Connect your TV TUNER (etc) to the TV IN terminal. Be sure to connect the video input. 3. Turn OFF the power to the TV TUNER and the SR-19. 4. Turn ON the TV TUNER and tune in a receivable station. 5. When the station is received, the SR-19 turns ON and TV is selected automatically. AUTO POWER OFF 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. 2. The SR-19 switches to STANDBY after approx. 5 minutes. Note: AUTO POWER OFF is canceled if the INPUT SELECTOR knob el is set to a source other than TV. The function reactivates when TV is selected again. Caution: Some TV broadcasts may cause the TV AUTO FUNCTION to be turned ON. To set this function ON/OFF, refer to the SETUP MENU. SETTING THE SLEEP TIMER (ONLY REMOTE CONTROL UNIT) Set the sleep timer while the power is turned on. 1. Turn the power ON and presS the SLEEP button D5 on page 4 at AMP mode. "SLEEP" blinks on the display. 2. Press the SLEEP button D5 the number of times to set the desired sleep time. Each press of the SLEEP button D5 changes the display in the following order: 10 20 ). 30 40 50 I OFF 4---- 90 80 4 70 4-- 60 "SLEEP" stops blinking and lights steadily. * While the sleep timer is activated, the remaining time can be is DIALOGUE NORMALIZATION MESSAGE Dialogue Normalization (Dial Norm) is a feature of Dolby Digital. displayed for approx. 2 seconds by pressing the SLEEP button. When playing back software which has been encoded in Dolby Digital, sometimes you may see a brief message in the front panel display which will read "Dial Norm X dB" (X being a numeric value). To cancel the sleep timer, press the SLEEP button D5 and then press the C (CLEAR) button Cl. Dialogue Normalization serves to let you know if the source material has been recorded at a higher or lower level than usual. For example, if you see the following message: "Dial Norm + 4 dB" in the front panel display, to keep the overall output level constant just turn down the volume control by 4 dB. In other words, the source material that you are listening to has been recorded 4 dB louder than usual. If you do not see a message or see "Dial Norm 0 dB" in the front panel display, then no adjustment of the volume control is necessary. 14