Marantz SR4200 User Guide - Page 19

ENGLISH BASIC OPERATION LISTENING TO THE TUNER MANUAL TUNING 1. To select the tuner as the source, press the TUNER button t on the front panel or press the TUNER button c on the remote. 2. Press the TUNER button t on the front panel or press the TUNER button c on the remote to select the desired frequency band if required. 3. Press the F/P button !4 on the front panel to display the frequency. 4. Press the TUNING/PRESET or button !3 on the front panel or press the 1 or ¡ button ⁄2 on the remote. 5. If FM is selected, press the MODE button !5 on the front panel or press the MODE button ⁄2 on the remote control to select the desired audio mode. (FM) MODE BUTTON OPERATION When "M" indicator is on in the display, FM stations that broadcast in stereo will be received in stereo and the "STEREO" indicator lights. When "M" indicator is off, all the FM stations will be received in mono regardless of whether or not they are broadcasting in stereo. AUTO TUNING (USING THE SR4200) 1. Press the F/P button !4 on the front panel to display the frequency. 2. Press the TUNING/PRESET or button !3 on the front panel for more than 1 second to start the Auto tuning function. AUTO TUNING (USING THE REMOTE CONTROL UNIT) Press 1 or ¡ button ⁄2 for more than 1 second to start the Auto tuning function. PRESET TUNING With this unit you can preset up to 50 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. 1-a. Manual Presetting (Using the SR4200) 1. Refer to the "MANUAL TUNING" or "AUTO TUNING" section above to tune in a desired station. 2. Press the MEMORY button !2. "MEMO" indicator starts blinking on the display. While "MEMO" is still blinking (approx. 5 seconds), select the preset number by pressing the TUNING/PRESET or button !3 then press the MEMORY button !2 again. 3. When a number has been properly input, "MEMO" indicator stops blinking and goes out. The station is now stored in the specified preset memory location. 1-b. Manual Presetting (Using the remote control unit) 1. Tune in a desired station. 2. Press the MEMO button ⁄6. 3. Enter the desired preset number with ten keypad .. * When entering a single digit number (2, for example), either input "02" or just input "2" and wait for a few seconds. 2. Auto Presetting This function automatically scans the AM and FM band and enters all stations with sufficient signal strength into the memory. 1. Select the FM band with the TUNER button t. 2. Tune in the lowest receivable frequency. 3. Press and hold down the MEMORY button !2 and TUNING/ PRESET button !3 simultaneously, auto presetting will starts. 4. Each time the tuner finds a station, the scanning will pause and memory. 5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. To stop the auto preset function at anytime, press the CLEAR button !1. 3. Recalling a Preset Station 1. Press the F/P button !4 to change the display to preset. 2. Select the desired preset station by pressing TUNING/PRESET or button !3 on the front panel or press CHANNEL button ⁄2 on the remote. Note: To directly access the preset stations using the numeric keypad, select the desired preset station by entering one or two digits using the numeric keypad .. To return to the Manual Tuning mode, press the F/P button !4. 4. Preset Scan Tuning (Using the remote control unit) 1. Press the P.SCAN button ⁄0 on the remote control. (The preset station with the smallest preset number is recalled first. If no stations have been preset, CH "00" blinks in the display and the unit returns to the previous mode.) 2. Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5 seconds each. Preset numbers that do not contain stations are skipped. 3. You can fast forward the preset stations by pressing the CHANNEL ¢ button ⁄2 continuously. When the desired preset station is received, cancel the preset scan operation by pressing the CHANNEL 4 button ⁄2 or the CLEAR button !.1 5. Clearing Preset Stations You can remove preset stations from memory using the following procedure. 1. Recall the preset number to be cleared with the method described in "Recalling" a preset station . 2. Press the MEMORY button !2 on the front panel or MEMO button ⁄6 on the remote unit, "MEMO" blinks in the display for 5 seconds. While "MEMO" is still blinking, press the CLEAR button !1 on the front panel or CLEAR button ⁄7 on the remote unit. "CLEAR" appears on the display to indicate that the specified preset number has been cleared. 12