Marantz SR6300 User Guide - Page 11

REMOTE CONTROLER RC7300SR ⁄2 (TV) CH 3/4 buttons Used to increase or decrease the TV channel. ENGLISH NAMES AND FUNCTIONS ⁄3 TOP MENU button z Infrared window Outputs and inputs an infrared control signals. x LCD (Liquid Crystal Display) Used to display information about currently selected functions. c / (open/close) button Used to open or close the door. v Source POWER ON/OFF button Used to turn specific sources (such as DVD players, etc.) ON and OFF independently from the rest of the system. b EQ button Used to turn on or off HT (Home Theater)-EQ mode when the surround mode is set as AUTO, DOLBY, DTS or STEREO. This mode compensates for the audio portion of a movie sounding "bright". When this button is pressed, "HT-EQ" indicator lights up. n V-OFF (video off) button Used to turn off the video signal. (when DVD mode is selected) Used to call up the top menu of the DVD. ⁄4 Tone / Deck cotrol buttons Tone cotrol buttons (when AMP mode is selected) The TREBLE buttons are used to adjust the tone control of high frequency sound for left and right speaker. The BASS buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker. Deck cotrol buttons (when Tape mode is selected) The DECK A button are used to select the deck A. The DECK B button are used to select the deck B. The 1 2 button are used to change the direction. ⁄5 CURSOR / OK button Used to operate on-screen and other displays used by receivers and other components. ⁄6 CH SEL. (channel select) button (when AMP mode is selected) Used to call up SETUP MAIN MENU and adjust speaker levels or 6.1 ch input level. Note: • This button is unavailable for SR6300. m DVD operating buttons (when DVD mode is selected) AUDIO button Used to select one of the audio language. ANGLE button Used to change the different camera angle. SUBTITLE button Used to select one of the subtitle language. , Numeric buttons 1 to 9, 0 / Surround mode buttons Numeric buttons Used to enter figures in the selection of a tuner preset station and station name preset or to set select a CD track number, etc. The functions of these buttons are dependent on the function button selected. Surround mode buttons (when AMP mode is selected) Used to select the surround mode. . CL (clear) / S-DIRECT (source direct) button Used to cancel for certain memory or programming operations. (when AMP mode is selected) Used to select the S-DIRECT (source direct) mode. In source direct mode, the tone control circuitry is bypassed. ⁄0 INPUT button Used to select monitor input. ⁄1 T.MODE button (when TUNER mode is selected) Used to select the auto stereo mode or mono mode when the FM band is selected. The "AUTO" indicator lights in the auto stereo mode. ⁄7 SETUP button (when DVD mode is selected) Used to call up the setup menu of the DVD. ⁄8 CONTROL buttons These buttons are used when operating the CD player, TAPE deck, etc. The function of these buttons are dependent on the function button selected. (when AMP mode is selected) SPK A/B button Speaker mode is switched in the following sequence. A → B → A+B → off ATT button When the input signal is too high and the voice distorts even by throttling the SR6300 VOLUME control, turn on this function. "ATT" is indicated when this function is activated. The input level is reduced. Attenuator is invalid for use with the output signal of "REC OUT". Note: • This function is unavailable during the digital input is selected. MULTI button This button is unavailable for SR6300. ⁄9 Input selector buttons/ FUNCTION SELECTOR buttons (AUDIO/VIDEO INPUT) Used to switch the remote controller to the command sets for specific sources (amplifier, receiver, etc.), thereby allowing a single remote controller to control up to 11 different components. To use these buttons to switch the amplifier's source, press the desired button twice within 2 seconds. The AMP button ⁄9 is used only to switch command set of the remote controller itself and therefore does not transmit any signal. Further, the function buttons may also be programmed to execute macros. (A macro allows a complex string of operations to be performed in series simply by pressing a single button.) One button can be programmed to learn sequences containing up to 10 commands. The following is an example of such a sequence that can be activated automatically using a macro: Turn the receiver ON → Switch the function to DVD → Set the Surround Mode to VIRTUAL → Set the DVD player to Play. Note: • The AUX2 button is unavailable for SR6300. 6