Marantz SR8500 SR7500 User Manual - Page 37

ENGLISH CLEARING STORED PRESET STATIONS You can remove preset stations from the memory using the following procedure. 2. 3. ST SPKR A B V-OFF PEAK ATT DISC 6.1 MT X 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR ENTER VOLUME DOWN DIGITAL AUX 1 INP S-VIDEO V TEST 1 7.1CH 4 DISP 7 CLEAR CH.SEL 2 ATT 5 OSD 8 THX 0 SURR 3 SPK-AB 6 SLEEP 9 MEMO 3. 2. TV DVD VCR DSS 1. Recall the preset number to be cleared with the method described in "Recalling" a preset station. 2. Press the MEMORY button on the front panel or press the MEMO button on the remote. 3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote. 4. "xx CLEAR" appears on the display to indicate that the specified preset number has been cleared. Note: • To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds. SORTING PRESET STATIONS AV SURROUND RECEIVER SR7500 INPUT SELECTOR DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MT X 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR STANDBY POWER ON/STANDBY PHONES ENTER VOLUME DOWN UP DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R If you have stations memorized, and there is a gap in the sequential order: I.e. the stations are stored as follows 1) 87.1 MHz 2) 93.1 MHz 3) 94.7 MHz 10) 105.9 MHz (notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press and hold the MEMORY and the cursor buttons. "PRESET SORT" will appear on the display and sorting will be done. NAME INPUT OF THE PRESET STATION. This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation. 4. 5. 2. 5. 6. AV SURROUND RECEIVER SR7500 INPUT SELECTOR DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MT X 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR VOLUME DOWN UP STANDBY POWER ON/STANDBY PHONES ENTER DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R CH VOL OK PREV 7 CLEAR LIP.SYNC 8 THX 0 MUTE 9 MEMO 5. 5. 2. 5. 6. SOURCE USE PAGE 2 M 4. D1 D2 4. D3 D4 4. D5 1. Recall the preset number to be inputted name with the method described in "Recalling" a preset station. 2. Press the MEMORY button on the front panel or press the MEMO button on the remote for more than 3 seconds. 3. The left most column of the station name indicator flashes, indicating the character entry ready status. 4. When you press the or cursor buttons on the front panel or the or buttons on the remote, alphabetic and numeric characters will be displayed in the following order: A → B → C ... Z → 1 → 2 → 3 ..... 0 Blank) → A UP → ← DOWN 5. After selecting the first character to be entered, press the MEMORY or ENTER button, or press the MEMO button on the remote. The entry in this column is fixed and the next column starts to flash. Fill the next column the same way. To move back and forth between the characters, press the / cursor buttons or press CH+ or CH- button on the remote. Note: • Unused columns should be filled by entering blanks. 6. To save the name, press the MEMORY or ENTER button on the front panel, or press the MEMO button on the remote for more than 2 seconds. Ten keypad 1 2 3 4 5 6 7 8 9 0 Press, press again, press again, etc. A → B → C → 1 → A D → E → F → 2 → D G → H → I → 3 → G J → K → L → 4 → J M → N → O → 5 → M P → Q → R → 6 → P S → T → U → 7 → S V → W → X → 8 → V Y → Z → space → 9 → Y 0 34