Marantz ZS5300 User Manual - Page 12

ID Code Setup

Get Marantz ZS5300 PDF manuals and user guides View all Marantz ZS5300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

ENGLISH ID Code Setup ❖ Setting ID code Ex.) Set to ID-1 Remote control unit INPUT 1 2 VOLUME 3 SET ID-1 ID-2 ID-3 REMOTE CONTROLLER RC5300ZS Press and hold SET, then Press ID-1 and release both. Rear panel of the unit ZONE 3 PRE OUT R L AUDIO IN R L AUDIO OUT ZONE DIRECT IN R L R L SPEAKERS (MINIMUM 6 OHMS) ZONE 1 ZONE 2 ZONE 3 R L R L R L 1 STATUS OUT REMOTE CONTROL ID ZONE 1 ZONE 3 SELECTOR 2 IN EXT. INT. 123 3 OUT ZONE 2 FLASHER IN Set to "1". The ZS5300 system can be expanded up to 3 units. When using 1 unit alone, set the ID switch on the rear panel to "1". To set the remote control unit to the ID number of the unit, follow the procedure below. 1. Press the SET button and hold it, then press the ID-1 button , then release both buttons. 2. This remote control unit has been set as ID-1. To set the ID to 2 and 3, follow the same procedure. 3. When the batteries are replaced, the unit defaults to the factory setting of ID-1. Note: This is important, because if you have changed ID numbers, you will have to reset the ID number when the batteries are replaced. *Default setting for both the remote control unit and the unit is ID-1 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
8
ENGLISH
❖
Setting ID code
Ex.)
Set to ID-1
Remote control unit
Press and hold
SET
, then
Press
ID-1
and release both.
Rear panel of the unit
Set to
“
1
”
.
R
3
2
1
3
ER
ER
REMOTE CONTROL
REMOTE CONTROL
OUT
OUT
T
T
ZONE
ZONE
1
L
SPE
SPE
SELECTOR
SELECTOR
INT.
INT.
EXT.
EXT.
IN
IN
ID
ID
T
T
VOLUME
ID-2
SET
ID-3
ID-1
INPUT
3
2
1
REMOTE CONTROLLER RC5300ZS
ID Code Setup
The ZS5300 system can be expanded up to 3 units.
When using 1 unit alone, set the ID switch on the rear panel to
“
1
”
.
To set the remote control unit to the ID number of the unit, follow the procedure below.
1.
Press the
SET
button and hold it, then
press the
ID-1
button , then release both buttons.
2.
This remote control unit has been set as ID-1. To set the ID to 2 and 3, follow the same procedure.
3.
When the batteries are replaced, the unit defaults to the factory setting of ID-1.
Note:
This is important, because if you have changed ID numbers, you will have to reset the ID number when the
batteries are replaced.
*Default setting for both the remote control unit and the unit is ID-1