Maytag MDB7749SAW Installation Guide - Page 11

Option C, Waste disposer - with air gap, Option D, No waste disposer - with air gap

Get Maytag MDB7749SAW PDF manuals and user guides View all Maytag MDB7749SAW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Option C, Waste disposer - with air gap Option D, No waste disposer - with air gap 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle-nose pliers to remove plug. 3. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 4. Attach drain hose to air gap with large blue drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp (not provided). 5. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from air gap to disposer inlet. 1. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 2. Attach drain hose to air gap with large blue drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to 5.1 cm) screw-type clamp (not provided). 3. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from waste tee to air gap. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
11
Option C, Waste disposer – with air gap
Option D, No waste disposer – with air gap
1.
Using a hammer and screwdriver,
knock plug into disposer.
2.
Use needle-nose pliers to remove
plug.
3.
Connect rubber end of drain hose to
air gap and cut if needed.
NOTE:
Do not cut ribbed section.
4.
Attach drain hose to air gap with
large blue drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1
¹⁄₂
"
to 2" (3.8 to 5 cm) screw-type clamp
(not provided).
5.
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from air gap to
disposer inlet.
1.
Connect rubber end of drain hose to
air gap and cut if needed.
NOTE:
Do not cut ribbed section.
2.
Attach drain hose to air gap with
large blue drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1
¹⁄₂
"
to 2" (3.8 to 5.1 cm) screw-type
clamp (not provided).
3.
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from waste tee
to air gap.