Maytag MRT118FFF Owners Manual 1 - Page 7

Reverse Freezer Door, Reverse Refrigerator Door

Get Maytag MRT118FFF PDF manuals and user guides View all Maytag MRT118FFF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

NOTE: Make sure the washers are in place on both the top and bottom pins of the center hinge. 4. Remove the shoulder screw and its washer from the left-hand side of the door and fasten it into the hole that was behind the brand badge. 5. Remove the door stop from the bottom of the freezer door. A B A A hex-head hinge screws B. Washers Reverse Freezer Door 1. Remove the three cabinet hole plugs from the top of the cabinet and place them in the hinge holes on the opposite side. A AB A. Door stop screw B. Door stop 6. Move the door stop to the opposite side, making sure that the hole in the door stop plate is aligned perfectly with the hole for the center hinge pin. 7. Using the screw removed earlier, fasten the door stop to the bottom of the freezer door. A A. Cabinet hole plugs 2. Remove the door handles. ■ Remove the two flat-head handle screws from the bottom of the freezer door handle. ■ Using the ¹⁄₈" hex key, loosen the setscrew attaching the top of the handle. ■ Pull the handle away from the door to release it from the shoulder screw. Keep all parts together. A B A. Door stop screw 8. Place the handle on the shoulder screw and push the handle toward the door until the mounting base is flush against the door. 9. Fasten the bottom of the handle to the bottom of the freezer door. 10. Tighten all screws. Set aside the freezer door until the hinges and refrigerator door are in place. Reverse Refrigerator Door 1. Remove the door stop from the bottom of the refrigerator door. C A. Shoulder screw B. Setscrew C. Flat-head handle screws 3. Using the plastic tool (provided), remove the brand badge from the freezer door by prying up the right-hand side and slowly peeling the badge away from the door, revealing the hole to mount the door handle. NOTES: ■ To avoid scratching the finish, do not use a sharp or metallic object to pry the brand badge from the door. ■ Rub a small amount of liquid dish soap over any adhesive residue with your fingers. Rinse the door with warm water and dry with a soft cloth. AB A. Door stop screw B. Door stop 2. Replace the door stop on the opposite side of the refrigerator door, making sure that the hole in the door stop plate is aligned perfectly with the hole for the bottom hinge pin. 3. Fasten the door stop to the door. 4. Remove the door handles. ■ Remove the screws from the top of the refrigerator door handle. ■ Remove the setscrew from the lower part of the handle. ■ Pull the handle away from the door to release it from the shoulder screw. Keep all parts together. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
7
NOTE:
Make sure the washers are in place on both the top
and bottom pins of the center hinge.
Reverse Freezer Door
1.
Remove the three cabinet hole plugs from the top of the
cabinet and place them in the hinge holes on the opposite
side.
2.
Remove the door handles.
■
Remove the two flat-head handle screws from the bottom
of the freezer door handle.
■
Using the
¹⁄₈
" hex key, loosen the setscrew attaching the
top of the handle.
■
Pull the handle away from the door to release it from the
shoulder screw. Keep all parts together.
3.
Using the plastic tool (provided), remove the brand badge
from the freezer door by prying up the right-hand side and
slowly peeling the badge away from the door, revealing the
hole to mount the door handle.
NOTES:
■
To avoid scratching the finish, do not use a sharp or
metallic object to pry the brand badge from the door.
■
Rub a small amount of liquid dish soap over any adhesive
residue with your fingers. Rinse the door with warm water
and dry with a soft cloth.
4.
Remove the shoulder screw and its washer from the left-hand
side of the door and fasten it into the hole that was behind the
brand badge.
5.
Remove the door stop from the bottom of the freezer door.
6.
Move the door stop to the opposite side, making sure that the
hole in the door stop plate is aligned perfectly with the hole for
the center hinge pin.
7.
Using the screw removed earlier, fasten the door stop to the
bottom of the freezer door.
8.
Place the handle on the shoulder screw and push the handle
toward the door until the mounting base is flush against the
door.
9.
Fasten the bottom of the handle to the bottom of the freezer
door.
10.
Tighten all screws. Set aside the freezer door until the hinges
and refrigerator door are in place.
Reverse Refrigerator Door
1.
Remove the door stop from the bottom of the refrigerator
door.
2.
Replace the door stop on the opposite side of the refrigerator
door, making sure that the hole in the door stop plate is
aligned perfectly with the hole for the bottom hinge pin.
3.
Fasten the door stop to the door.
4.
Remove the door handles.
■
Remove the screws from the top of the refrigerator door
handle.
■
Remove the setscrew from the lower part of the handle.
■
Pull the handle away from the door to release it from the
shoulder screw. Keep all parts together.
A.
⁵⁄₁₆
" hex-head hinge screws
B. Washers
A. Cabinet hole plugs
A. Shoulder screw
B. Setscrew
C. Flat-head handle screws
A
A
B
A
B
A
C
A. Door stop screw
B. Door stop
A. Door stop screw
A. Door stop screw
B. Door stop
A
B
A
A
B