NEC 50016755 E900 User Manual
NEC 50016755 - MultiSync E900 Plus Manual
 |
UPC - 050927215360
View all NEC 50016755 manuals
Add to My Manuals
Save this manual to your list of manuals |
NEC 50016755 manual content summary:
- NEC 50016755 | E900 User Manual - Page 1
NEC Enterprise Series MultiSync®® E900™™ UUsseerr''ss MMaannuuaall Contents 1 Quick Start 2-3 Controls 4-5 Recommended Use 6-7 Specifications 8 Features 9 Troubleshooting 10 References 11 Limited Warranty 12 Untitled-1 1 6/15/98, 1:24 PM - NEC 50016755 | E900 User Manual - Page 2
VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF avoid any problems. Canadian Department cables with the JC-1941UMA color monitor so as not to interfere with accordance with the instructions, may cause television technician for additional suggestions. The - NEC 50016755 | E900 User Manual - Page 3
Your new NEC Technologies MultiSync® E Series monitor box* should contain the following: • MultiSync E900™ (JC-1941UMA) Monitor with tilt/swivel base • Power Cord • Captive Signal Cable • User's Manual • Registration Card Power Cord NEC Advanced Series MEu9l0t0iSync User's Manual ®® PRODUCT - NEC 50016755 | E900 User Manual - Page 4
of the power cord to the MultiSync E900 monitor and the other end to the power outlet (Figure C.1). 5. Turn on the monitor (Figure D.1) and the computer. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. Captive Signal Cable Untitled-1 15-pin mini - NEC 50016755 | E900 User Manual - Page 5
Quick Start Captive Signal Cable Computer Power Outlet Mac Adapter (Not included) Figure B.1 15-pin mini D-SUB Power Cord Figure C.1 Untitled-1 EXIT PROCEED RESET CONTROL Figure D.1 3 5 MultiSync E900 6/15/98, 1:24 PM - NEC 50016755 | E900 User Manual - Page 6
(On-Screen Manager) control buttons on the front of the monitor function as follows: EXIT Exits the OSM controls. CONTROL ᮤ PROCEED Enters OSM menu and selects icons at the top of the menu. RESET Resets the highlighted control to the factory setting. Brightness/Contrast Controls Adjusts the - NEC 50016755 | E900 User Manual - Page 7
the electron beams and monitor. IPM™ System: On: The IPM System works normally and all stages of energy savings are utilized. Off: The Off Mode of the IPM System is not used. NOTE: For standard systems and graphics boards, keep the factory setting at ON. Selecting ALL RESET allows you to reset - NEC 50016755 | E900 User Manual - Page 8
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC® E900™ COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock - NEC 50016755 | E900 User Manual - Page 9
look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from checkups. For more detailed information on setting up a healthy work environment, call NEC at (800) 820-1230, NEC FastFacts™ information at (800) - NEC 50016755 | E900 User Manual - Page 10
Supported Resolution based on horizontal and vertical frequencies only Active Display Area (Factory Setting E900™ Monitor Notes 19 inch 18.0 inch 1330 mm 90° deflection, 0.28 mm trio dot pitch, medium short persistence phosphor, multi-layered, anti-static screen coating NEC 35°C 30% to 80% 0 to 10, - NEC 50016755 | E900 User Manual - Page 11
precise, continuous focus adjustments of the electron beams and optimum image quality, even Allows you to change between two color settings on your display to match your personal setup and installation by allowing the monitor to send its capabilities (such as screen size and resolutions supported - NEC 50016755 | E900 User Manual - Page 12
Troubleshooting No picture • Display card should be completely seated in its slot. • the picture • Move electrical devices that may be causing electrical interference away from the monitor. • See inside cover of User's Manual for FCC information. Edges of the display image are not square • Use the - NEC 50016755 | E900 User Manual - Page 13
-4298 • Electronic Channels: Internet e-mail: [email protected] Internet ftp site: ftp.nectech.com CompuServe: go NECTECH World Wide Web: http://www.nec.com • FastFacts™ Information (800) 366-0476 INFORMATION DESCRIPTION DOCUMENT # MultiSync® E900™ monitor Detailed monitor information - NEC 50016755 | E900 User Manual - Page 14
NEC Technologies, Inc. (hereinafter "NECTECH"), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set supplied components. Service required as an original bill of sale or receipt containing name instructions contained in the User's Manual software, - NEC 50016755 | E900 User Manual - Page 15
t t Notes Untitled-1 13 15 6/15/98, 1:25 PM - NEC 50016755 | E900 User Manual - Page 16
Monitor Equipment Classification: Class B Peripheral Models: JC-1941UMA We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. MultiSync is a registered trademark of NEC Technologies, Inc. in the U.S. and of NEC Home Electronics
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
MultiSync
®
E
900
™
User’s Manual
MultiSync
®
E
900
™
User’s Manual
NEC Enterprise Series
Contents
1
Quick Start
2-3
Controls
4-5
Recommended Use
6-7
Specifications
8
Features
9
Troubleshooting
10
References
11
Limited Warranty
12
Untitled-1
6/15/98, 1:24 PM
1