Netgear CSM4532 Installation Guide - Page 2

Option 1. Configure the IP address for access over the service port To disable DHCP and manually configure the IP address so that you can access the switch over the service port, enter the following commands: (switch)#configure (switch)#serviceport protocol none (switch)#serviceport ip ipaddress netmask [gateway] The following configuration is an example: (switch)#serviceport ip 192.168.2.23 255.255.255.0 192.168.2.1 Option 2. Configure the switch as a DHCP client for access over the service port To enable the DHCP client for dynamic IP address assignment so that you can access the switch over the service port, enter the following commands: (switch)#configure (switch)#serviceport protocol dhcp Option 3. Configure the switch IP address for access over an Ethernet port To disable DHCP and manually configure the IP address settings so that you can access the switch over an Ethernet port, enter the following commands: (Switch)#configure (Switch)(config)#interface vlan 1 (Switch)(if-vlan 1)#ip address ipaddress netmask (Switch)(if-vlan 1)#exit (Switch)(Config)#ip default-gateway gateway The following configuration is an example: (Switch)(if-vlan 1)#ip address 192.168.1.253 255.255.255.0 (Switch)(Config)#ip default-gateway 192.168.1.254 August 2019 © NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only. Option 4. Configure the switch as a DHCP client for access over an Ethernet port To enable the DHCP client for dynamic IP address assignment so that you can access the switch over an Ethernet port, enter the following commands: (Switch)#configure (Switch) (Config)#interface vlan 1 (Switch) (if-vlan1)#ip address dhcp Note: For information about CLI management, see the CLI reference manual, which you can download by visiting netgear.com/support/download/. Find the IP address assigned by the DHCP server To find the IP address that the DHCP server assigned to the switch's service port or management interface, connect a computer or VT100/ANSI terminal to the RJ-45 RS232 console port on the switch. 1. Make sure that the switch is connected to a DHCP server. 2. Set up a console connection with the switch. For information about setting up a console connection, see . After you are logged in and at the CLI command prompt, continue with the next step. 3. At the command prompt, type one of the following commands: • To find the IP address of the service port, type the show serviceport command, and press Enter. • To find the IP address of the management interface, type the show ip interface command, and press Enter. The active IP address displays. 4. Write down the IP address for later use. 3. Configure and manage the switch To configure and manage the switch, log in to the switch over a Telnet connection to port 1223 and the IP address of either the service port or the management interface, type the telnet IP address 1223 command, and press Enter. You must use port 1223. For example, if the IP address of the management interface is 192.168.1.253, type the telnet 192.168.1.253 1223 command, and press Enter. Available publications For more information, see the following guides and manual, which you can download by visiting netgear.com/support/download/: • Hardware installation guide • Software administration and configuration guide • CLI reference manual Support Thank you for purchasing this NETGEAR product. You can visit https://www.netgear.com/support/ to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources. Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français canadien à https://www.netgear.com/support/download/. (If this product is sold in Canada, you can access this document in Canadian French at https://www.netgear.com/support/download/.) For regulatory compliance information including the EU Declaration of Conformity, visit https://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply. Do not use this device outdoors. If you connect cables or devices that are outdoors to this device, see https://kb.netgear.com/000057103 for safety and warranty information. NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA NETGEAR INTERNATIONAL LTD Floor 1, Building 3 University Technology Centre Curraheen Road, Cork, T12EF21, Ireland