Netgear FWG114Pv2 FWG114Pv2 Installation Guide - Page 1
Netgear FWG114Pv2 - Wireless Firewall With USB Print Server Manual
View all Netgear FWG114Pv2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
)NSTALLATION'UIDE ProSafe Wireless 802.11g Firewall/Print Server Model FWG114P v2 Start Here Please refer to the Reference Manual on your CD for instructions on advanced configuration options. Estimated Completion Time: 20 minutes. Prepare to Install Your FWG114P v2 • For Cable Modem Service: When you set up the wireless firewall/print server, be sure to use the computer you first registered with your cable modem service provider. • For DSL Service:You may need information such as the DSL login name and password in order to complete the wireless firewall/print server setup. First, Connect the FWG114P v2 to the Internet 1. Connect the wireless firewall/print server to your computer and modem a. Turn off and unplug your cable or DSL modem. b. Turn off your computer. c. At the computer end only, disconnect the Ethernet cable (point A in the illustration) that connects your computer to the cable or DSL A modem. &DEOH ,QWHUQHW &RPSXWHU 0RGHP d. Securely insert the Ethernet cable from your modem into the ,QWHUQHW3RUW FWG114P v2 Internet port (point B in the illustration). e. Securely insert one end of the B ,QWHUQHW blue NETGEAR cable that came with your FWG114P v2 into a Local port on the router such as 53" -/$%- ,/#!, ).4%2.%4 - 6$# ! ):*3Y &DEOH 0RGHP port 4 (point C in the illustration), and the other end into the Ethernet port of your computer (point D in the illustration). D %OXH1(7*($5 &DEOH C ,QWHUQHW &RPSXWHU 53" -/$%- ):*3Y ,/#!, ).4%2.%4 - 6$# ! /FDO3RUWV 0RGHP 2. Restart your network in the correct sequence Warning: Failure to restart your network in the correct sequence could prevent you from connecting to the Internet. a. First, plug in and turn on the cable or DSL modem.Wait about 2 minutes. b. Now, plug in the power cord to your FWG114P v2 and wait about 30 seconds. c. Last, turn on your computer. Note: For DSL customers, if ISP provided software logs you in to the Internet, do not run that software. You may need to go to the Internet Explorer® Tools menu, Internet Options, Connections tab page where you can select the "Never dial a connection" radio button and click Apply. d. Check the status lights and verify the following: Broadband ProSafe 802.11g Wireless Firewall/Print Server PWR ACT TEST ALERT PR IN TER ACT LINK M O DEM 100 1 LNK/ACT IN TER N ET 2 3 LO CA L MODEL FWG114P 100 4 LNK/ACT W LA N Power Test Internet Port Local Port 4 Wireless • Power: The power light should be lit. If after 2 minutes the power light turns solid amber, see the Troubleshooting Tips in this guide. • Test: The test light blinks when the the FWG114P v2 is first turned on. If after 2 minutes it is still on, see the Troubleshooting Tips in this guide. • Internet: The Internet light on the FWG114P v2 should be lit. If not, make sure the Ethernet cable is securely attached to the wireless firewall/print server Internet port and the powered on modem. • Wireless: The WLAN light should be lit. If the Wireless light is not lit, see the Troubleshooting Tips in this guide. • LOCAL: A LOCAL light should be lit. 3. Log in to the wireless firewall/print server a. On the computer connected to the FWG114P v2, open a browser such as Internet Explorer or Netscape® Navigator. b. Type http://192.168.0.1 in your browser and click Enter. If you did not connect to the router, verify that your computer is set up for DHCP. For help with this, please see the animated tutorials on the CD or Appendix C of the Reference Manual. c. When prompted, enter admin for the router user name and password for the router password, both in lower case letters. d. After logging in, you will see the Setup Wizard on the FWG114P v2 settings main page.