Netgear GS516UP Installation Guide

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3,

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

Installation Guide

16-Port Gigabit Ethernet Unmanaged

Ultra60 PoE++ Switch, Model GS516UP

24-Port Gigabit Ethernet Unmanaged

Ultra60 PoE++ Switch, Model GS524UP

Package contents

•

Switch model GS516UP or GS524UP

•

Power cord (varies by region)

•

Rack-mount kit

•

Four rubber feet

•

Installation guide and Insight flyer

Note:

We recommend that you use a Category 5e (Cat 5e) cable or higher-rated cable for

Gigabit Ethernet connections.

This switch is designed for indoor use only. If you want to connect to a device located

outdoors, the outdoor device must be properly grounded and surge protected, and you

must install an Ethernet surge protector inline between the switch and the outdoor device.

Failure to do so can damage the switch.

WARNING:

Before connecting this switch to outdoor cables or devices, see

https://kb.netgear.com/000057103

for safety and warranty information.

1. Register with the NETGEAR Insight app

1.

Search for

NETGEAR Insight

and download the latest app.

2.

Set up a NETGEAR account if you do not have one.

3.

Tap the menu in the upper-left corner.

4.

Tap

REGISTER ANY NETGEAR DEVICE

.

5.

Enter the serial number located on the bottom of the switch, or use the

camera on your mobile device to scan the serial number bar code.

6.

Tap

GO

.

The switch is registered and added to your account. You can now view the

switch in the NETGEAR Insight app.

Note:

Because this is an unmanaged switch, you cannot configure or manage it

in NETGEAR Insight.

2. Connect the switch

PoE++ LED lighting

Internet

GS524UP switch

Sample connections

PoE++ PTZ camera

PoE+ security camera

Router

3. Check the LEDs

When you connect the power cord to the switch and plug it into an electrical

outlet, the LEDs indicate the status.

LED

Description

Power

Solid green

. The switch is powered on and operating normally.

Off

.

Power is not supplied to the switch.

Fan

Off

. The fan is working correctly.

Solid yellow

. The fan is not working correctly.

PoE Max

(The status of

the switch’s PoE

budget)

Off

. Sufficient (more than 7W of) PoE power is available.

Solid yellow

. Less than 7W of PoE power is available.

Blinking yellow

. At least once during the previous two minutes, less

than 7W of PoE power was available.

Left port LED

Solid green

.1000 Mbps link on this port.

Blinking green

. 1000 Mbps activity on this port.

Solid yellow

. 100 Mbps or 10 Mbps link on this port.

Blinking yellow

. 100 Mbps or 10 Mbps activity on this port.

Off

. No link is detected on this port.

Right Port LED

Solid Green

. The port is delivering PoE power..

Off

. The port is not delivering PoE power.

Solid yellow

. A PoE fault occurred.

PoE mode

The DIP switches on the front panel let you to select the following PoE++ modes:

•

802.3bt mode

. The mode for devices that are fully compliant with

IEEE 802.3bt (PoE++).This is the default mode for all PoE++ ports.

•

pre-802.3bt mode

. The mode for devices that

can

receive power higher

than 30W but that are not fully compliant with IEEE 802.3bt (PoE++).

Continued on the next page

.

Computer

Internet

PoE++

non-PoE

Model GS516UP provides PoE++ (802.3bt) power on ports 1–8 with up to 60W to

each port and PoE+ (802.3at) power on ports 9–16 with up to 30W to each port. The

total PoE power budget for the switch is 380W across all active PoE ports.

Model GS524UP provides PoE++ (802.3bt) power on ports 1–16 with up to 60W to

each port and PoE+ (802.3at) power on ports 17–24 with up to 30W to each port.

The total PoE power budget for the switch is 480W across all active PoE ports.

PoE++ speaker

PoE+

PoE+ access point

ReadyNAS

Netgear GS516UP Installation Guide

Netgear GS516UP Manual

Netgear GS516UP manual content summary: