Netgear GSM7324 FSM7326P Command line reference manual

Netgear GSM7324 - ProSafe Layer 3 Managed Gigabit Switch Manual

Get Netgear GSM7324 - ProSafe Layer 3 Managed Gigabit Switch PDF manuals and user guides
UPC - 606449029062
View all Netgear GSM7324 manuals
Add to My Manuals
Save this manual to your list of manuals

Netgear GSM7324 manual content summary:

  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 1
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Version 6.0 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10236-01 February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 2
    document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. EN 55 022 Declaration of Conformance This is to certify that the ProSafe 7300 Series Layer-3 Managed Switch operating instructions. The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 3
    : Publication Date: Product Family: Product Name: Home or Business Product: Language: Publication Part Number: Publication Version Number FSM7326P, GSM7324, GSM7312 February 2007 managed switch ProSafe 7300 Series Layer-3 Managed Switch Business English 202-10236-01 1.0 iii v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 4
    iv v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 5
    Contents Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Version 6.0 Chapter 1 About This Manual 1.1...Audience 1-1 1.2...Scope 1-1 1.3 Typographical Conventions 1-2 1.4 Special Message Formats 1-2 1.5 How to Use This Manual 1-3 1.6 How to Print this
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 6
    show network 3-3 3.2 Configuring the Switch Management CPU (ezconfig) 3-5 ip http secure-port 3-17 3.6.2 ip http secure-protocol 3-18 3.6.3 ip http secure-server 3-18 3.6.4 ip http server 3-18 3.6.5 network javamode 3-19 3.6.6 ...show ip http 3-19 3.7 User Account Commands 3-20 3.7.1 ...users
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 7
    users snmpv3 authentication 3-22 3.7.5 users snmpv3 encryption 3-22 3.7.6 show loginsession 3-23 3.7.7 ...show users 3-23 3.7.8 ...disconnect 3-24 Chapter 4 Port and System Setup Commands 4.1 Port Configuration Commands 4-1 4.1.1 ...interface 4-1 4.1.2 interface range 4-2 4.1.3 interface vlan
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 8
    mac-address-table multicast 4-18 4.4.6 show mac-address-table static 4-19 4.4.7 show mac-address-table staticfiltering 4-20 4.4.8 show mac-address-table stats 4-20 4.5 DNS Client Commands 4-21 4.5.1 ip domain-lookup 4-22 4.5.2 ip domain-name 4-22 4.5.3 ip name-server 4-22 4.5.4 ...ip host
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 9
    ...vlan 6-2 6.1.4 vlan acceptframe 6-2 6.1.5 vlan ingressfilter 6-3 6.1.6 vlan makestatic 6-3 6.1.7 ...vlan name 6-4 6.1.8 vlan participation 6-4 6.1.9 vlan participation all 6-5 6.1.10 vlan port acceptframe all 6-5 6.1.11 vlan port pvid all 6-6 6.1.12 vlan port tagging all 6-6 6.1.13 vlan
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 10
    6-14 6.3.1 vlan port priority all 6-14 6.3.2 ...vlan priority 6-14 Chapter 7 DHCP Commands 7.1 DHCP Server Commands (DHCP Config Pool Mode) 7-2 7.1.1 ...ip dhcp pool 7-2 7.1.2 client-identifier 7-2 7.1.3 ...client-name 7-3 7.1.4 default-router 7-3 7.1.5 ...dns-server 7-4 7.1.6 hardware-address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 11
    ip dhcp ping packets 7-10 7.2.3 service dhcp 7-10 7.2.4 ip dhcp bootp automatic 7-11 7.2.5 ip dhcp conflict logging 7-11 7.3 DHCP Server Clear and Show Commands 7-12 7.3.1 clear ip dhcp binding 7-12 7.3.2 clear ip dhcp server statistics 7-12 7.3.3 clear ip dhcp conflict 7-12 7.3.4 show ip
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 12
    9-1 9.1.1 ...port-security 9-2 9.1.2 port-security max-dynamic 9-2 9.1.3 port-security max-static 9-3 9.1.4 port-security mac-address 9-3 9.1.5 port-security mac-address move 9-3 9.1.6 show port-security 9-4 9.1.7 show port-security 9-4 9.1.8 show port-security dynamic 9-4 9.1.9 show port
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 13
    11-3 11.1.4 dot1x defaultlogin 11-3 11.1.5 dot1x initialize 11-3 11.1.6 ...dot1x login 11-3 11.1.7 dot1x max-req 11-4 11.1.8 dot1x port-control 11-4 11 timeout 11-6 11.1.14 dot1x user 11-7 11.1.15 users defaultlogin 11-8 11.1.16 users login 11-8 11.1.17 show authentication 11-8 xiii v1.0,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 14
    -9 11.1.19 show dot1x 11-9 11.1.20 show dot1x users 11-13 11.1.21 show users authentication 11-13 11.2 RADIUS Commands 11-13 11.2.1 radius -channel 12-6 12.2.2 show port-channel 12-6 Chapter 13 Quality of Service (QoS) Commands 13.1 Class of Service (CoS) Commands 13-1 xiv v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 15
    13-14 13.3.11 match ip precedence 13-15 13.3.12 match ip tos 13-15 13.3.13 match protocol 13-16 13.3.14 match source-address mac 13-16 13.3.15 match srcip 13-17 13.3.16 match srcl4port 13-17 13.3.17 match vlan 13-17 13.4 DiffServ Policy Commands 13-17
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 16
    -19 13.4.5 ...class 13-20 13.4.6 ...mark cos 13-20 13.4.7 mark ip-dscp 13-21 13.4.8 mark ip-precedence 13-21 13.4.9 police-simple 13-21 13.4.10 policy-map rename 13-22 13.5 DiffServ Service Commands 13-23 13.5.1 service-policy 13-23 13.6 DiffServ Show Commands 13-24 13.6.1 show class
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 17
    Routing Commands 14-7 14.2.1 ...routing 14-7 14.2.2 ...ip routing 14-7 14.2.3 ...ip address 14-8 14.2.4 ...ip route 14-8 14.2.5 ip route default 14-9 14.2.6 ip route distance 14-10 14.2.7 ip forwarding 14-10 14.2.8 ip netdirbcast 14-11 14.2.9 ...ip mtu 14-11 14.2.10 encapsulation 14-12 14.2.11
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 18
    -19 14.3.2 ip irdp address 14-19 14.3.3 ip irdp holdtime 14-20 14.3.4 ip irdp maxadvertinterval 14-20 14.3.5 ip irdp minadvertinterval 14-21 14.3.6 ip irdp preference 14-21 14.3.7 show ip irdp 14-21 14.4 Virtual LAN Routing Commands 14-22 14.4.1 vlan routing 14-22 14.4.2 show ip vlan 14-23
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 19
    (OSPF) 14-38 14.6.22 default-metric (OSPF) 14-39 14.6.23 distance ospf 14-39 14.6.24 distribute-list out 14-40 14.6.25 exit-overflow-interval 14-40 14.6.26 external-lsdb-limit 14-41 14.6.27 ip ospf areaid 14-41 14.6.28 ip ospf authentication 14-42 14.6.29
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 20
    Information Protocol (RIP) Commands 14-60 14.7.1 ...router rip 14-60 14.7.2 enable (RIP) 14-60 14.7.3 ...ip rip 14-60 14.7.4 auto-summary 14-61 14.7.5 default-information originate (RIP) 14-61 14.7.6 default-metric (RIP) 14-61 14.7.7 distance rip 14-62 14.7.8 distribute-list out 14-62 14
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 21
    .2.1 show ip igmp 15-6 15.2.2 show ip igmp mrouter interface 15-8 15.2.3 show ip igmp mrouter vlan 15-8 15.2.4 show mac-address-table igmpsnooping 15-8 15.3 IGMP Querier Commands 15-9 15.3.1 ip igmpsnooping querier 15-10 15.3.2 ip igmpsnooping querier ip-address 15-10 15.3.3 ip igmpsnooping
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 22
    17.2.7 clear port-channel 17-18 17.2.8 clear traplog 17-18 17.2.9 clear vlan 17-19 17.2.10 ...copy 17-19 17.2.11 ...logout 17-21 17.2. 17-26 17.3.12 show logging traplogs 17-27 17.4 CLI Command Logging Command 17-27 17.4.1 logging cli-command 17-27 17.5 Configuration Scripting Commands 17-28
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 23
    Relay Commands 18.1 UDP Relay Configuration Commands 18-2 18.1.1 ip helper-address (global config mode) 18-2 18.1.2 ip helper-address (interface config mode) 18-3 18.2 UDP Relay Show Commands 18-3 18.2.1 show ip helper-address 18-3 Appendix A Command Changes from Release 3 to Release 5 xxiii
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 24
    xxiv v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 25
    used to view and configure the 7300 Series Managed Switch software. You can access the CLI by using a direct connection to the serial port or by using telnet or SSH over a remote network connection. 1.1 Audience This document is for system administrators who configure and operate systems using
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 26
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Note: Product updates are available on the NETGEAR Web site at http://kbserver.netgear.com/products/. 1.3 Typographical Conventions This guide uses the following typographical conventions: Table 1-2.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 27
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 1.5 How to Use This Manual The HTML version of this manual includes the following: • Buttons and one page at a time. for browsing forwards or backwards through the manual •A button that displays the table of
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 28
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • Printing the Full Manual. Use the Complete PDF Manual link at the top left of any page. - Click the Complete PDF Manual link at the top left of any page in the manual. The PDF version of the complete manual opens in a browser
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 29
    2.1 Scope 7300 Series Managed Switch software encompasses both hardware and software support. It software is partitioned to run in the using a remote logical connection with telnet or SSH. This section describes the CLI syntax, conventions, and modes. It contains the following topics: • Section
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 30
    ProSafe 7300 Series Layer-3 Switches, Software Ver- • Section 2.2.4 "Using the "No" Form of a Command" on page 2-5 • Section 2.2.5 "Command Modes" on page 2-6 • Section 2.2.6 "Entering CLI Commands" on page 2-8 • Section 2.2.7 "Using CLI the command. • Default shows the default value, if any,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 31
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.2 Command Conventions In this document, the command name is in bold font. Parameters are in italic font. You must replace the parameter name with an appropriate value, which might be a name or number.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 32
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.2.1 Common Parameter Values IP address. You can enter the IP address in the following formats: a (32 bits) a.b (8.24 bits) a.b.c (8.8.16 bits) a.b.c.d (8.8.8.8) In addition to these formats, the CLI
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 33
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.3 Slot-Port Naming Convention 7300 Series Managed Switch software references physical entities such as cards and ports by using a Slot-Port (SP) naming convention. The software functions. VLAN routing or reset a value back to the default. For
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 34
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.5 Command Modes The CLI groups commands into modes according to the command function. Each of the command modes supports specific 7300 Series Managed Switch software commands. The commands in one mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 35
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Table 2-5. CLI Command Modes (continued) Command Mode Prompt Policy Class Config Switch (Config policy-class-map)# Class Map Config Switch (Config class-map)# Router OSPF Config Router RIP Config
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 36
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- Table 2-6. CLI Mode access-list extended . From the Global Config mode, enter ip dhcp pool . Exit or Access Previous Mode To exit to Ctrl-Z. 2.2.6 Entering CLI Commands The 7300 Series Managed Switch supports several features to
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 37
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2.2.6.2 CLI Error Messages If you enter a command and the system is unable to execute it, an error message appears. Table 2-7 describes the most common CLI error messages. Table 2-7. CLI Error Messages Message Text
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 38
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Table 2-8. CLI Editing Conventions Key VLAN ID of the switch. If the help output shows a parameter in angle brackets, you must replace the parameter with a value. (switch) #network parms ? Enter the IP Address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 39
    ProSafe 7300 Series Layer-3 Switches, Software Ver- You can also enter a question mark (?) after typing one or more characters of a word to list the available command or parameters that begin with the letters, as shown in the following example: (switch) #show m? mac-addr-table mac-address-table
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 40
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 2-12 v1.0, February 2007 Overview
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 41
    basic port configuration commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 3.6 "Hypertext Transfer Protocol (HTTP) Commands" on page 3-17 • Section 3.7 "User Account Commands" on page 3-20 The commands in this section are divided into two
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 42
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.1.2 network parms (parameter) This command sets the IP Address, subnet mask and gateway of the device. The IP Address Management VLAN ID to the default. the network information for the switch manually. Default none Format network protocol
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 43
    switched or routed. Format show network Modes Privileged EXEC User EXEC IP Address The IP address of the interface. The factory default value is 0.0.0.0 Subnet Mask The IP subnet mask for this interface. The factory default value is 0.0.0.0 Default Gateway The default gateway for this IP
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 44
    . The options are bootp | dhcp | none. Specifies if the switch should allow access to the Java applet in the header frame. Enabled means the applet can be viewed. The factory default is disabled. Specifies if the switch should allow access to the Web Interface. 3-4 Administrative Access Commands
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 45
    are CLI commands that can be used to do this, ezconfig simplifies the task. The tool is applicable to all NETGEAR 7000-series managed switches, and allows you to configure the following parameters: 1. The administrator's user password and administrator-enable password 2. Management CPU IP address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 46
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The following is an example of an ezconfig session. NETGEAR EZ Configuration Utility Hello and Welcome! This utility will walk you thru assigning the IP address for the switch management CPU. It will allow
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 47
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- There are changes detected, do you wish the Global Config mode, you can configure a variety of system settings, including user accounts. From the Global Config mode, you can enter other command modes,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 48
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.3.3 serial baudrate This command specifies the communication rate of the terminal interface. The supported rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. Default 9600 Format serial baudrate
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 49
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.3.5 show serial This command displays serial communication settings for the switch. Format show serial Modes Privileged EXEC User EXEC Serial Port Login 38400,57600, and 115200 baud. The factory default is 9600 baud. Character Size (bits)
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 50
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4 Telnet Commands This section The host value must be a valid IP address. Valid values for port should be a valid decimal integer in the range of 0 to 65535, where the default value is 23. If [debug] is
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 51
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4.3 transport output telnet This command the session is ended or an abnormal network error ends it. Default enabled Format transport output telnet Mode Line Config 3.4.3.1 no transport output
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 52
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4.5 session-timeout This command sets the telnet session timeout value.The timeout value unit of time is minutes. A value of 0 indicates that a session remains active indefinitely. Default timeout value to the default. The timeout value unit
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 53
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.4.7 telnetcon the telnet connection session timeout value to the default. Note: Changing the timeout value for active show telnet Modes Privileged EXEC User EXEC Outbound Telnet Login Timeout Indicates the number of
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 54
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- User EXEC Remote Connection Login Timeout (minutes) This object indicates the number of minutes a remote connection session is allowed to remain inactive before being logged off. May be specified as a number from 1 to 160. The factory default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 55
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.5 Secure Shell (SSH) Command This section describes the commands you use to configure SSH access to the switch. Use SSH to access the switch from a remote management host. Note: The system allows a
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 56
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.5.3 sshcon maxsessions This command specifies the maximum number of SSH connection sessions that can be established. A value of 0 indicates that no ssh connection can be established. The range is 0 to 5. Default 5 Format sshcon
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 57
    section describes the commands you use to configure HTTP access to the switch. Access to the switch by using a Web browser is enabled by default. Everything you can view and configure by using the CLI is also available by using the Web. 3.6.1 ip http secure-port This command is used to set the SSL
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 58
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.6.2 ip http secure-protocol This command is used to set protocol levels (versions). The protocol level can be set to TLS1, SSL3 or to both TLS1 and SSL3. Default SSL3 and TLS1 Format ip http secure-protocol [SSL3
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 59
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.6.5 network javamode This command specifies whether or not the switch should allow access to the Java applet in the header frame of the Web interface. When access is enabled, the Java applet can be
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 60
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7 User Account Commands This section describes the commands you use to add, manage, and delete system users. The 7300 Series Managed Switch has two default users: admin and guest. The admin user can view and configure
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 61
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7.2 users passwd Use this command to change a password. Passwords are a maximum of eight alphanumeric characters. If a user is authorized for authentication or encryption is enabled, the password length must be at
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 62
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7.4 users snmpv3 authentication This command specifies the authentication protocol to be used for the specified user. The valid authentication protocols are none, md5 or sha. If you specify md5 or sha, the login password is also
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 63
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.7.5.1 no users snmpv3 encryption This command sets the encryption protocol to none. The is the login user name for which the specified encryption protocol will be used. Format no users snmpv3 encryption Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 64
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- SNMPv3 Access Mode SNMPv3 Authentication SNMPv3 Encryption This field displays the SNMPv3 Access Mode. If the value is set to ReadWrite, the SNMPv3 user is able to set and retrieve parameters on the system
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 65
    general port and system setup commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 4.1 "Port Configuration Commands" on page 4-1 • Section 4.2 "Pre-login Banner and System Prompt Commands" on page 4-9 • Section 4.3 "Simple Network Time
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 66
    interface. The interface must be put under a VLAN group and an IP address assigned to the VLAN group. Format Mode interface lag Global Config 4.1.5 auto-negotiate This command enables automatic negotiation on a port. Default enabled Format auto-negotiate Mode Interface Config
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 67
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.5.1 no auto-negotiate This command To configure the IP MTU size, which is the maximum size of the IP packet (IP Header + IP payload), see Section 14.2.9 "ip mtu" on page 14-11. Default Format Mode 1518
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 68
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.7.1 no mtu This command sets the default MTU size (in physical and port-channel (LAG) interfaces, but not on VLAN routing interfaces. Default Format Mode enabled shutdown Interface Config 4.1.8.1 no shutdown This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 69
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.9 shutdown all This command disables all ports. Note: You can use the shutdown command on physical and port-channel (LAG) interfaces, but not on VLAN routing interfaces. Default Format Mode enabled shutdown
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 70
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.11 speed all This command sets the destination monitored port and all VLANs. Once the port is removed from the VLAN, the user must manually add the port to any desired VLANs. Note: This command sets
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 71
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.1.13 no monitor This command removes all the source ports and a destination port and restores the default value for mirroring session mode for all the configured sessions. Note: This is a stand-alone "no"
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 72
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- or disabled. The factory default is enabled. Selects the desired port speed and duplex mode. If auto-negotiation support is selected, then group name of an entry in the Protocol-based VLAN table. Group ID This field displays the group
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 73
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interface Media login at the User: prompt. 4.2.1 copy The copy command includes the option to upload or download the CLI Banner to or from the switch. You can specify local URLs by using TFTP, Xmodem, Ymodem, or Zmodem. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 74
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3 Simple Network Time Protocol (SNTP) sntp broadcast client poll-interval This command resets the poll interval for SNTP broadcast client back to the default value. Format no sntp broadcast client poll
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 75
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3.3 sntp client port This command sets the SNTP client port id to a value from 1-65535. Default 123 Format sntp client port Mode Global Config 4.3.3.1 no sntp client port This command resets the SNTP client
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 76
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3.5.1 no sntp unicast client poll-timeout This command resets the poll timeout for SNTP unicast clients to its default value. Format no sntp unicast client poll-timeout Mode Global Config 4.3.6 sntp
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 77
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.3.8 sntp server This command configures an SNTP server (a maximum of three). The optional priority can be a value of 1-3, the version a value of 1-4, and the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 78
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Client Supported Modes SNTP Version Port Client Mode Poll Interval Poll Timeout Poll Retry Supported SNTP Modes (Broadcast, Unicast, or Multicast). The highest SNTP version the client supports SNTP Client Port Configured
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 79
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Port Last Attempt Time Last offset Number of minutes difference with UTC Mode Global Config Default [no] clock timezone 4.4 MAC Address and MAC Database Commands This section describes the commands you
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 80
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.1 network mac-address This command sets locally administered MAC addresses. The following rules apply: • Bit 6 of byte 0 (called the U/L bit) indicates whether the address is universally administered (b'0') or
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 81
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.3 bridge aging-time This command configures the forwarding database address aging timeout in seconds. In an IVL system, the [fdbid | all] parameter is required. Default 300 Format bridge aging-time
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 82
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.4 show forwardingdb agetime This command displays the timeout for address aging. In an IVL system, the [fdbid | all] parameter is required. Default all Format show forwardingdb agetime [fdbid | all
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 83
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interfaces Forwarding address and VLAN. Format show mac-address-table static { | all} Mode Privileged EXEC MAC Address Is the MAC Address of the static MAC filter entry. VLAN ID Is the VLAN
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 84
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.4.7 show mac-address-table staticfiltering This command displays the Static Filtering entries in the Multicast Forwarding Database (MFDB) table. Format show mac-address-table staticfiltering Mode Privileged
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 85
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.5 DNS Client Commands The Domain Name System (DNS) is an Internet directory service. DNS is used to translate domain names to IP addresses. A DNS Client (often referred to as a resolver) uses a defined
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 86
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4.5.1 ip domain-lookup To enable the IP Domain Naming System (DNS)-based host name-to-address translation, use the ip domain-lookup global configuration command. To disable the DNS, use the no form of this
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 87
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode [no] ip host name address Global Config 4.5.5 clear host To delete entries from the host name-to-address display the default domain name, a list of name server hosts, the static and the cached list of host names and addresses, use
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 88
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 4-24 Port and System Setup Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 89
    protocol (STP) commands available in the 7300 Series Managed Switch CLI. STP helps prevent network loops, duplicate messages, and default. If STP is disabled, the system does not generate BPDU messages. 5.1.1 spanning-tree This command sets the spanning-tree operational mode to enabled. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 90
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.1.1 no spanning-tree This command sets the configuration that this switch is currently using. The is a string of up to 32 characters. Default base MAC address in hexadecimal notation Format
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 91
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.4 spanning-tree configuration revision This command sets the Configuration Identifier Revision Level for use in identifying the configuration that this switch the configuration that this switch is currently using to the default value, i.e. 0.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 92
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.6.1 no spanning-tree than MST BPDUs (IEEE 802.1w functionality supported) • 802.1s - MST BPDUs are transmitted (IEEE 802.1s functionality supported) Default 802.1s Format spanning-tree forceversion
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 93
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.8.1 no spanning-tree forward-time This command sets the Bridge Forward Delay parameter for the common and internal spanning tree to the default value of 15. Format no spanning-tree forward-time Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 94
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.11 spanning-tree max-hops This command sets the MSTP Max Hops parameter to a new value for the common and internal spanning tree. The max-hops value is a range from 1 to 127. Default 20 Format spanning-tree
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 95
    ProSafe 7300 Series Layer-3 Switches, Software for this port for mst '0' instance, to the default value, i.e. a path cost value based on The maximum number of multiple instances supported by the switch is 4. Format spanning-tree instance from the switch and reallocates all VLANs allocated to the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 96
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Global Config 5.1.14 spanning-tree mst tree to the default value, i.e. 32768. Format spanning-tree mst priority Mode Global Config 5.1.15 spanning-tree mst vlan This command adds
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 97
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.15.1 no spanning-tree mst vlan This command removes an association between a multiple spanning tree instance and a VLAN so that the VLAN sets the Administrative Switch Port State for all ports to enabled. Default disabled Format spanning-
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 98
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.1.18 spanning-tree bpduforwarding Normally a switch will not forward Spanning Tree Protocol (STP) BPDU packets if STP is disabled. However, if in some network setup, the user wishes to forward BDPU packets
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 99
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- Associated VLANs Time in seconds. Number of times changed. Boolean value of the Topology Change parameter for the switch indicating up using the bridge priority and the base MAC address of the bridge. Path Cost to the CST Regional Root. List
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 100
    ProSafe 7300 Series Layer-3 Switches, Software switch. The following details are displayed on execution of the command. Format show spanning-tree summary Modes Privileged EXEC User EXEC Spanning Tree Adminmode Enabled or disabled. Spanning Tree Version Version of 802.1 currently supported
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 101
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Configuration Digest Key MST Instances Identifier used to identify the configuration currently being used. List of all multiple spanning tree instances configured on the switch 5.2.3 show spanning-tree interface
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 102
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 5.2.4 show spanning-tree mst port detailed This command displays the detailed settings and parameters for a specific switch desired switch port. Format show spanning-tree mst port detailed Mode Privileged EXEC User EXEC
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 103
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Designated Bridge Designated Port Identifier Bridge Identifier of the bridge with the Designated Port. Port on the Designated Bridge that offers the lowest cost to the LAN. If you specify 0 (defined as the default CIST ID) as
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 104
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- CST default CIST ID) as the , the status summary displays for one or all ports within the common and internal spanning tree. Format show spanning-tree mst port summary { | all} Modes Privileged EXEC User
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 105
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Associated FIDs Associated VLANs List of forwarding database identifiers associated with this instance. List of VLAN IDs associated with this instance. 5.2.7 show spanning-tree vlan This command displays the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 106
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 5-18 Spanning Tree Protocol Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 107
    in the 7300 Series Managed Switch CLI. VLANs allow users located on different physical networks to be on the same logical network. The VLAN Commands section includes the following topics: • Section 6.1 "VLAN Configuration Commands" on page 6-1 • Section 6.2 "VLAN Show Commands" on page 6-11
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 108
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.2 network mgmt_vlan This command configures the Management VLAN ID. Default 1 Format network mgmt_vlan Mode Privileged EXEC 6.1.2.1 no network mgmt_vlan This command sets the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 109
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.4.1 no vlan acceptframe This command sets the are members of that VLAN. Default disabled Format vlan ingressfilter Mode Interface Config 6.1.5.1 no vlan ingressfilter This command disables
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 110
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.7 vlan name This command changes the name of a VLAN. The name is an alphanumeric string of up to 32 characters, and the ID is a valid VLAN identification number. ID range is 1-4094. Default VLAN ID 1 - default; other VLANS - blank
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 111
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.9 vlan participation all This command configures the degree of participation for all interfaces in a VLAN. The ID is a valid VLAN identification number. Format vlan participation all {exclude | include
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 112
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.10.1 no vlan port acceptframe all VLAN Specification. Format no vlan port acceptframe all Mode Global Config 6.1.11 vlan port pvid all This command changes the VLAN ID for all interface. Default 1 Format vlan
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 113
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.13 vlan port ingressfilter all This command enables ingress filtering for all ports. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 114
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.16.1 no vlan protocol group add protocol This command removes the from this protocol-based VLAN group that is identified by this . The possible values for protocol are ip, arp, and ipx. Format
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 115
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.19 protocol vlan group This command adds the physical interface to the protocol-based VLAN identified by . You can associate multiple interfaces with a group, but you can only associate each
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 116
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.1.21 vlan pvid This command changes the VLAN ID per interface. When an untagged packet comes to the switch, it will be tagged with the PVID value as the VLAN ID for further processing. By default, every port belongs to VLAN 1 and the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 117
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.2 VLAN Show Commands This section describes the commands you use to view VLAN settings. 6.2.1 show vlan This command displays a list of all configured VLANs. Format show vlan Modes Privileged EXEC User EXEC VLAN ID There
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 118
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interface Current Configured Tagging to allow the port to be dynamically registered in this VLAN via GVRP. The port will not participate in this VLAN unless a join request is received on this port. This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 119
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.2.3 show vlan port This command displays VLAN port information. Format show vlan port { | all} Modes Privileged EXEC User VLAN bridge specification. The factory default is disabled. GVRP May be enabled or disabled. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 120
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 6.3 Provisioning (IEEE 802.1p) Commands This section describes the commands you use to configure provisioning, which allows you to prioritize ports. 6.3.1 vlan port priority all This command configures
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 121
    commands available in the 7300 Series Managed Switch CLI. DHCP automatically allocates and manages client TCP/ IP configurations. DHCP uses UDP as its transport protocol and supports a number of features that facilitate in administration address allocations. The DHCP Server Commands section includes
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 122
    to configure the DHCP server settings for the switch. 7.1.1 ip dhcp pool This command configures a DHCP address pool name on a DHCP server and enters DHCP pool configuration mode. Default none Format ip dhcp pool Mode Global Config Note: The CLI mode changes to DHCP Pool Config mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 123
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.2.1 IP address 0.0.0.0 is invalid. Default none Format default-router [....] Mode DHCP Pool Config 7.1.4.1 no default-router This command removes the default router list. Format no default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 124
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.5 dns-server This command specifies the IP servers available to a DHCP client. Address parameters are valid IP addresses; each made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid. Default none Format
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 125
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode host [mask | prefix-length] DHCP Pool Config 7.1.7.1 no host This command removes the IP address of the DHCP client. Format no host Mode DHCP Pool Config 7.1.8 lease This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 126
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.9 network Use this command to configure the subnet number and mask for a DHCP address pool on the server. Network-number is a valid IP address, made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 127
    Switches, Software Ver- 7.1.11.1 no domain-name This command removes the domain name. Format no domain-name Mode DHCP Pool Config 7.1.12 netbios-name-server This command configures NetBIOS Windows Internet Naming Service (WINS) name servers that are available to DHCP clients. One IP address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 128
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.1.13.1 no netbios-node-type This command removes the NetBIOS node Type. Format no netbios-node-type Mode DHCP Pool Config 7.1.14 next-server This command configures the next server in the boot process of a DHCP client. Address is the IP
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 129
    255. IP address 0.0.0.0 is invalid. Default none Format ip dhcp excluded-address [highaddress] Mode Global Config 7.2.1.1 no ip dhcp excluded-address This command removes the excluded IP addresses for a DHCP client. Low-address and high-address are valid IP addresses; each made
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 130
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.2.2 ip dhcp ping packets This command is used to specify the number, in a range from 2-10, of packets a DHCP server sends to a pool address as part of a ping operation. By default the number of packets sent
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 131
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.2.4 ip dhcp bootp automatic This command enables the allocation of the addresses to the bootp client. The addresses are from the automatic address pool. Default disabled Format ip dhcp bootp automatic Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 132
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.3 DHCP Server Clear and Show Commands This section describes the commands you to delete various DHCP information and the commands you use to view DHCP configuration information and statistics. 7.3.1 clear ip dhcp binding This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 133
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- IP address Hardware Address Lease expiration Type The IP address of the client. The MAC Address or the client identifier. The lease expiration time of the IP Address assigned to the client. The manner in which IP Address was assigned
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 134
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The following additional field is displayed for Dynamic pool type: Network The network number and the mask for the DHCP address pool. The following additional fields are displayed for Manual pool type: Client Name
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 135
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- DHCP RELEASE DHCP INFORM no IP address is specified, all the conflicting addresses are displayed. Format show ip dhcp conflict [ip-address] Modes Privileged EXEC User EXEC IP address The IP address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 136
    client request originated. The remote ID option contains the MAC address of the relay agent (the switch management CPU's own MAC address). Default disabled Format ip dhcp relay information option Mode Global Config 7.4.1.1 no ip dhcp relay information option This command disables the relay
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 137
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.4.3 bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The parameter has a range of 1 to 16. Default 4 Format bootpdhcprelay maxhopcount
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 138
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7.4.5 bootpdhcprelay serverip This command configures the server IP Address for BootP/DHCP Relay on the system. The parameter is an IP address in a 4-digit dotted decimal format. Default 0.0.0.0 Format bootpdhcprelay
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 139
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Discarded Is the number of packets discarded. 7.4.7 bootpdhcprelay backup-serverip To configure the IP address no bootpdhcprelay backup-serverip Mode Global Config Default no bootpdhcprelay backup-serverip DHCP Commands v1.0, February
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 140
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 7-20 v1.0, February 2007 DHCP Commands
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 141
    GVRP), and Garp Multicast Registration Protocol (GVMP) commands available in the 7300 Series Managed Switch CLI. GARP is a protocol that allows client stations to register with the switch for membership in VLANS (by using GVMP) or multicast groups (by using GMRP). This section contains the following
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 142
    the ProSafe 7300 Series Layer-3 Switches, Software Data Units (PDUs) registering (or reregistering) membership for a VLAN or multicast group. This command has an effect only when GVRP time (for one or all ports and per GARP) to the default. Note: This command has an effect only when GVRP is enabled
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 143
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.1.2 set garp timer leave This command sets the GVRP leave time. Leave time is the time to wait after receiving an unregister request for a VLAN or a multicast group before deleting the VLAN entry. This can be
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 144
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.1.3 set garp timer leaveall This 10 seconds. Note: This command has an effect only when GVRP is enabled. Default Format Modes 1000 set garp timer leaveall Interface Config Global Config
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 145
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.1.4 show garp This command displays GARP information. Format show garp Modes Privileged EXEC User EXEC GMRP Admin Mode This displays the administrative mode of GMRP for the system. GVRP Admin Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 146
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.2.2 set gvrp interfacemode This command enables GVRP. Default User EXEC VLAN or multicast group. This may be considered a buffer time for another station to assert registration for the same attribute in order to maintain uninterrupted service
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 147
    ProSafe 7300 Series Layer-3 Switches, Software Ver- LeaveAll Timer Port GMRP Mode GARP participant basis. Permissible values are 20 to 600 centiseconds (0.2 to 6.0 seconds). The factory default devices in the bridged LAN that support Extended Filtering Services. Note: If GMRP is disabled,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 148
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 8.3.1.1 no an interface that has GARP enabled. Default disabled Format set gmrp interfacemode Modes configuration { | all} Modes Privileged EXEC User EXEC Interface This displays the slot/port of the interface
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 149
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Join Timer Leave Timer LeaveAll Timer Port GMRP Mode Specifies the interval between the transmission of GARP PDUs registering (or re-registering) membership for an attribute. Current attributes are a VLAN or multicast group
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 150
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Type Description Interfaces hexadecimal numbers that are separated by colons, for example 01:23:45:67:89:AB. In an IVL system the MAC address is displayed as 8 bytes. Displays the type of the entry. Static
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 151
    commands available in the 7300 Series Managed Switch CLI. This section includes the following topics: switch. Port security, which is also known as port MAC locking, allows you to secure the network by locking allowable MAC addresses on a given port. Packets with a matching source MAC address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 152
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.1 port-security This command enables port locking at the system level (Global Config) or port level (Interface Config) Default command resets the maximum of dynamically locked MAC addresses allowed on a specific port to its default value.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 153
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.3 port-security max-static This command sets the maximum number of statically locked MAC addresses allowed on a specific port. Default 20 Format port-security max-static Mode Interface
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 154
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.6 show port-security This command . Dynamic Limit Maximum dynamically allocated MAC Addresses. Static Limit Maximum statically allocated MAC Addresses. Violation Trap Mode Whether violation traps
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 155
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.1.10 show port-security violation This command displays the source MAC address of the Speed High Low 10M 20 10 100M 5 2 1000M 5 2 Default Format Mode enabled storm-control broadcast Config Port-Based Traffic Control
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 156
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.1.1 no storm-control broadcast This command The thresholds are defined in the same way as for broadcast. Default disable Format storm-control multicast all Mode Config 9.2.2.1 no storm-control
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 157
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.3.1 no storm-control unicast all the same as the ones for broadcast storm control in Global mode. Default enable Format storm-contol broadcast [] Mode Interface Config 9.2.4.1 no storm
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 158
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.5.1 no storm-control multicast This the same as the ones for broadcast storm control in Global mode. Default enable Format storm-control unicast [] Mode Interface Config 9.2.6.1 no storm
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 159
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9.2.7.1 no storm-control flowcontrol This command disables 802.3x flow control for the switch. Note or disabled. The factory default is disabled. 802.3x Flow Control Mode May be enabled or disabled. The factory default is disabled. Port-
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 160
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 9-10 Port-Based Traffic Control Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 161
    SNMP commands available in the 7300 Series Managed Switch CLI. You can configure the switch to act as a Simple Network Management Protocol the switch, and the organization responsible for the network. The range for , and is from 1 to 31 alphanumeric characters. Default none
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 162
    to access the device. A value of 0.0.0.0 allows access from any IP address. Otherwise, this value is ANDed with the mask to determine the range of allowed client IP addresses. The name is the applicable community name. Default 0.0.0.0 Format snmp-server community ipaddr Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 163
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.3.1 no snmp-server community ipaddr This command sets a client IP address for an 's IP address for the client IP Address. A value of 0.0.0.0 will allow access from any IP address. The name is the applicable community name. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 164
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.5.1 no snmp-server community disallowed MAC address is received on a locked port. Note: For other port security commands, see Section 9.1 "Port Security Commands" on page 9-1. Default Format Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 165
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.8.1 no snmp-server traps violation This command disables the sending of new violation traps. Format no snmp-server traps violation Mode Interface Config 10.1.9 snmp-server traps This command enables the Authentication Flag. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 166
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.11 snmp-server traps linkmode This command enables Link Up/Down traps for the entire switch. When enabled, link traps are sent only if the Link Trap flag setting associated with the port is enabled.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 167
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.13.1 no snmp-server more information, see Section 10.1.2 "snmp-server community" on page 10-2. Default snmpv2 Format snmptrap [snmpversion ] Mode Global Config 10
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 168
    > can be snmpv1 or snmpv2. Note: This command does not support a "no" form. Default Format Mode snmpv2 snmptrap snmpversion Global Config 10.1.16 snmptrap ipaddr This command assigns an IP address to a specified community name. The maximum length of name is
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 169
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 10.1.18 snmp trap link-status This command enables link status traps by interface. Note: This command is valid only when the Link Up/
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 170
    ProSafe 7300 Series Layer-3 Switches, Software supported. You can add, change, or delete communities. The switch does not have to be reset for changes to take effect. The SNMP agent of the switch contain a unique community name. Client IP Address An IP address (or portion thereof) from which this
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 171
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- Client IP Mask Access Mode Status Subnet Mask is set to 0.0.0.0, an IP Address of 0.0.0.0 matches all IP addresses. The default value is 0.0.0.0 A mask to be ANDed with the requesting entity's IP address before comparison with IP Address. If
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 172
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Authentication Flag Link Up/Down Flag Multiple Users Flag Spanning Tree Flag Broadcast Storm Flag DVMRP Traps OSPF Traps PIM Traps Can be enabled or disabled. The factory default is enabled. Indicates whether
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 173
    and authentication commands available in the 7300 Series Managed Switch CLI. The Port-Based Access and Authentication Commands section to network services only to and devices that are authorized and authenticated. 11.1.1 authentication login This command creates an authentication login list. The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 174
    authentication method in the user's login (authentication login list) is attempted. The 7300 Series Managed Switch software does not utilize multiple entries in the user's login. If the first entry returns a timeout, the user authentication attempt fails. Note: The default login list included with
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 175
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.2 clear dot1x statistics This command resets the 802.1x statistics for the authentication login list assigned to a specific user if the user is configured locally. If this value is not configured, users will be
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 176
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.7 dot1x max-req This authentication exchanges between the supplicant, authenticator and the authentication server. Default auto Format dot1x port-control {force-unauthorized | forceauthorized |
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 177
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.8.1 no dot1x port- the authentication exchanges between the supplicant, authenticator and the authentication server. Default auto Format dot1x port-control all {force-unauthorized | force-authorized
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 178
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.11 dot1x re-authentication This command enables re-authentication of the supplicant for the specified port. Default timeout configurable parameters are set. The following tokens are supported. reauth-period: Sets the value, in seconds, of
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 179
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- quiet default values are set. Format no dot1x timeout {reauth-period | quiet-period | tx-period | supp-timeout | server-timeout} Mode Interface Config 11.1.14 dot1x user This command adds the specified user to the list of users
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 180
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.14.1 no dot1x user This command removes the user from the list of users with access to the specified port or all ports. Format no dot1x user { | all} Mode Global Config 11.1.15
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 181
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Method 1 Method 2 Method 3 This displays the first method in the specified authentication login list, if any. This displays the second method in the specified authentication login list, if any. This displays
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 182
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Control Mode Operating Control Mode Reauthentication Enabled Key Transmission Enabled The configured control mode for this port. Possible values are force-unauthorized | force-authorized |
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 183
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Supplicant Timeout Server Timeout Maximum Requests Reauthentication Period Reauthentication Enabled Key Transmission Enabled Control Direction The timer used by the authenticator state machine on
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 184
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- EAPOL Logoff Frames Received Last version number carried in the most recently received EAPOL frame. The source MAC address carried in the most recently received EAPOL frame. The number of EAP response/
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 185
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.1.20 show dot1x users This command displays 802.1x port security user information for locally configured users. Format show dot1x users Mode Privileged EXEC User Users configured locally to have
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 186
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.1.1 no default value. Note: To re-configure a RADIUS authentication server to use the default UDP , set the parameter to 1812. If you use the parameter, the command configures the IP address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 187
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.2.1 no radius server shared secret is configured for the RADIUS authentication or RADIUS accounting server. The IP address provided must match a previously configured server. When this command is executed, the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 188
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.5 radius server primary This command is used to configure the primary RADIUS authentication server for this RADIUS client. The primary server is the one that is used by default for handling RADIUS requests
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 189
    default value. Format no radius server timeout Mode Global Config 11.2.8 show radius This command is used to display the various RADIUS configuration items for the switch as well as the configured RADIUS servers. Format show radius [servers] Mode Privileged EXEC Primary Server IP Address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 190
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 11.2.9 show radius accounting the RADIUS accounting server details are displayed. Mode Enabled or disabled IP Address The configured IP address of the RADIUS accounting server. Port The port in use by
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 191
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Bad Authenticators Pending Requests or configured server. To show the configured RADIUS server statistic, the IP Address specified must match that of a previously configured RADIUS server. On execution
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 192
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Access Accepts Access Rejects Access Challenges Malformed Access Responses Bad Authenticators Pending Requests Timeouts Unknown Types Packets Dropped The number of RADIUS Access-Accept
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 193
    in the 7300 Series Managed Switch CLI. Port channels are also the source and destination MAC address. The Port-Channel/LAG switch. For every configuration command, there is a show command that displays the configuration setting. • Clear commands clear some or all of the settings to factory defaults
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 194
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1 Port-Channel Configuration Commands This section describes the commands you use to configure port-channels. Assign the LAG VLAN membership after you create a LAG. If you do not assign VLAN membership, the LAG might
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 195
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1.4 port-channel This command configures a new port- support of port-channels (static link aggregations) on the device. By default, the static capability for all port-channels is disabled. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 196
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1.6.1 no port-channel staticcapability This command disables the support of static port-channels on the device. Format no port-channel staticcapability Mode Global Config 12.1.7 port lacpmode This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 197
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12.1.9.1 no port-channel adminmode all sets every configured port-channel with the same administrative mode setting. Default enabled Format port-channel linktrap { | all} Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 198
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12 port-channels. Format show port-channel Modes Privileged EXEC User EXEC Static Capability This field displays whether or not the factory default is enabled. 12-6 Port-Channel/LAG (802.3ad) Commands v1.0,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 199
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Link Trap Mode STP Mode Mbr Ports Port Speed Type Active Ports This object determines whether or not to send a trap when link status changes. The factory default is enabled. The Spanning Tree Protocol
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 200
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 12-8 Port-Channel/LAG (802.3ad) Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 201
    Service (QoS) commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 13.1 "Class of Service (CoS) Commands" on page 13-1 • Section 13.2 "Differentiated Services " on page 13-31 • Section 13.8 "IP Access Control List (ACL) Commands" on page
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 202
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.1 ip-precedence-mapping This command maps an IP precedence value to a default internal traffic class value Format no classofservice ip-precedence-mapping Modes Global Config Interface Config 13-2 Quality of Service
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 203
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.3 classofservice ip-dscp-mapping This command maps an IP DSCP value to an internal traffic class. The value is specified as either an integer from 0 to 63, or symbolically through one of the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 204
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.5 cos-queue min-bandwidth This command specifies the minimum transmission bandwidth guarantee for each interface queue. The total number of queues supported queue strict This command restores the default weighted scheduler mode for each
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 205
    ProSafe 7300 Series Layer-3 Switches, Software shaping rate to the default value. Format no traffic user priority value is mapped. 13.1.9 show classofservice ip-precedence-mapping This command displays the current IP that support independent per-port class of service mappings. If specified, the IP
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 206
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode show classofservice ip-precedence-mapping [slot/ port] Privileged EXEC The following information is repeated for each user priority. IP Precedence The IP Precedence value. Traffic Class The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 207
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.1.11 show classofservice trust This command displays the current trust mode setting for a specific interface. The slot/port parameter is optional and is only valid on platforms that support independent per-port class of service mappings
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 208
    ProSafe 7300 Series Layer-3 Switches, Software Ver- If you specify the interface, the following information also appears: Interface This displays the slot/port of the interface. If displaying the global configuration, this output line is replaced policy/class combination 3. Service • Adding and
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 209
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • Class definitions do not support hierarchical service policies A given class definition can contain a maximum of one reference to another class. You can combine the reference with other match criteria.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 210
    ProSafe 7300 Series Layer-3 Switches, Software delete and re-create the entire class. The CLI command root is class-map. 13.3.1 class- DiffServ class. Note: The class-map-name 'default' is reserved and must not be used. a member of the class. Note: The CLI mode is changed to Class-Map Config when
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 211
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.1.1 no class-map This command eliminates an existing DiffServ class. The is the name of an existing DiffServ class ( The class name 'default Mode Class-Map Config Quality of Service (QoS) Commands v1.0, February 2007 13-11
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 212
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.5 match class-map This command adds to the specified class definition the set no match class-map Mode Class-Map Config 13-12 Quality of Service (QoS) Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 213
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.6 match cos This command adds to the specified class definition a match condition for the Class of Service value (the only tag in a single tagged packet or the first or outer 802.1Q tag of a double VLAN tagged packet). The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 214
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- To specify the match condition as a single keyword, the value for is one of the supported port name keywords. The currently supported values are: domain, echo, ftp, ftpdata, http, smtp,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 215
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.11 match ip precedence This command adds to the specified class definition a match condition based on the value of the IP Precedence field in a packet, which is defined as the high-order three bits of the Service Type octet
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 216
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.13 match protocol This command adds to the specified class definition a match condition based on the value of the IP ). Default none Format match source-address mac Mode Class-Map Config 13-16 Quality of Service (QoS
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 217
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.3.15 match srcip This command adds to the specified class definition a match condition based on the source IP address of a packet. The parameter specifies an IP address. The parameter specifies an IP address bit mask
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 218
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Use the policy commands to associate a traffic class that you define by using the class command set with one or more QoS policy attributes. Assign the class/policy association to an interface to form a service class instance. The CLI command root is
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 219
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.4.1.1 no from 0 to n-1, where n is the number of egress queues supported by the device. Format assign-queue Mode Policy-Class-Map Quality of Service (QoS) Commands v1.0, February 2007 13-19
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 220
    ProSafe 7300 Series Layer-3 Switches, Software to the class definition. Note: The CLI mode is changed to Policy-Class- associated traffic stream with the specified class of service value in the priority field of the or outer 802.1Q tag of a double VLAN tagged packet). If the packet does not already
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 221
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Default Format Mode Incompatibilities 1 mark-cos Policy-Class-Map Config Drop, Mark IP DSCP, IP Precedence, Police 13.4.7 mark ip defaults to transmit and the violate action defaults to drop. Quality of Service (QoS) Commands v1.0,
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 222
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- For set- cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef. For set-prec-transmit, an IP Precedence value is required. It is an integer from 0-7. For set-cos-transmit an 802.1p Quality of Service (QoS) Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 223
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.5 DiffServ Service Commands Use the DiffServ service commands to assign This set of commands consists of service addition/removal. The CLI command root is service-policy. 13.5.1 service-policy This command attaches a policy to
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 224
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.5.1.1 no service-policy This command detaches existing DiffServ class. Format show class-map Modes Privileged EXEC User EXEC If the class-name is specified the following fields are displayed: Class
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 225
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Values the user. The fields are evaluated in accordance with the class type. The possible Match Criteria fields are: Destination IP Address, Destination Layer 4 Port, Every, IP DSCP, IP Precedence, IP TOS, Protocol Keyword
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 226
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Policy Instance Table Size Policy Instance Table Max Policy Attribute Table Size Policy Attribute Table Max Service Table Size Service traffic classifier to specify which one of the supported hardware queues are used for handling packets belonging
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 227
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Committed Burst Size (KB) Committed Rate (Kbps) Conform Action Conform COS Conform DSCP Value Conform IP Precedence Value Drop Mark CoS Mark IP DSCP Mark IP on the same interface. Denotes the class of service value that is set in the 802.1p header
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 228
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Non-Conform COS Non-Conform DSCP Value Non-Conform IP Precedence Value Policing supported). Class Members List of all class names associated with this policy. 13.6.4 show diffserv service This command displays policy service
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 229
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Operational Status Policy Name Policy Details The current operational status of this DiffServ service interface. The name of the policy attached to the interface in the indicated direction. Attached policy
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 230
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Interface Direction Operational Status Policy Name Privileged EXEC Valid slot and port number separated by forward slashes. The traffic direction of this interface service. The current operational status of
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 231
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.6.7 show service-policy This command displays a summary of policy-oriented statistics information for all interfaces in the specified direction. Format show service-policy in Mode Privileged EXEC
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 232
    ProSafe 7300 Series Layer-3 Switches, Software Ver- If a MAC ACL by this name already exists, this command enters Mac-Access-List config mode to allow updating the existing MAC ACL. Note: The CLI Note: The 'no' form of this command is not supported since the rules within a MAC ACL cannot be deleted
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 233
    the ProSafe 7300 Series Layer-3 Switches, Software vlan and cos parameters refer to the VLAN identifier and 802.1p user priority fields, respectively, of the VLAN tag. For packets containing a double VLAN IP access list "match every" rule. Quality of Service (QoS) Commands v1.0, February 2007 13-33
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 234
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode {deny|permit} { | any} { | any} [ | ] [vlan the specified mac access list replaces the currently attached mac access platforms that support independent per-port class of service queue
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 235
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode Rule Number Action Source MAC Address Destination MAC Address Ethertype VLAN ID COS Assign Queue Redirect Interface show mac access-lists [name] Privileged EXEC The ordered rule number
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 236
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • Wildcard masking for ACLs operates differently from a subnet mask. A wildcard mask is in essence the inverse of a subnet mask. With a subnet mask, the mask has ones (1's) in the bit positions that are used for the network address, and
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 237
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- IP Extended ACL: Format Mode access-list {deny | permit} {every | {{icmp | igmp | ip | tcp | udp | } [{eq { | } [{eq {| <
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 238
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13.8.3 show ip access-lists This command displays an IP ACL is the number used to identify the IP ACL. Format show ip access-lists Mode Privileged EXEC Rule
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 239
    ProSafe 7300 Series Layer-3 Switches, Software Ver- ACL ID Sequence Number Access List name for a MAC access list or the numeric identifier for an IP access list replaces the currently attached access list using that sequence number. If the sequence number is not specified by the user, a sequence
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 240
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 13-40 Quality of Service (QoS) Commands v1.0, February 2007
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 241
    section describes the routing commands available in the 7300 Series Managed Switch CLI. This section contains the following topics: • Section 14.1 "Address Resolution Protocol (ARP) Commands" on page 14-1 • Section 14.2 "IP Routing Commands" on page 14-7 • Section 14.3 "Router Discovery Protocol
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 242
    Layer-3 Switches, Software Ver- The format is 6 two-digit hexadecimal numbers that are separated by colons, for example 00:06:29:32:81:40. Format arp Mode Global Config 14.1.1.1 no arp This command deletes an ARP entry. The value for is the IP address of the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 243
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.1.3.1 no arp cachesize This command configures the default ARP cache dynamicrenew Mode Privileged EXEC 14.1.5 arp purge This command causes the specified IP address to be removed from the ARP cache. Only entries of type dynamic or
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 244
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Global Config 14 valid positive integer, which represents the IP ARP entry ageout time in seconds. The range for is between 15-21600 seconds. Default 1200 Format arp timeout
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 245
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Mode Privileged EXEC 14.1.10 each ARP entry. IP Address Is the IP address of a device on a subnet attached to an existing routing interface. MAC Address Is the hardware MAC address of that device.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 246
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Type Age Is the type that was configured into the unit. The possible values are Local, Gateway, Dynamic and Static. This field displays the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 247
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2 IP Routing Commands This section describes the commands you use to enable and configure IP routing on the switch. 14.2.1 routing This command enables routing for an interface. You can view the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 248
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.3 ip address This command configures an IP address on an interface. You can also use this command to configure one or more secondary IP addresses on the interface. The value for is the IP Address route, the user controls whether a
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 249
    value of the static route is reset to its default. Format no ip route [{ | }] Mode Global Config 14.2.5 ip route default This command configures the default route. The value for is a valid IP address of the next hop router. The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 250
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.6 ip route distance This command sets the default distance for static routes. Lower route preference values are preferred when determining the best route. The ip route and ip route default commands allow you to
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 251
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.8 ip netdirbcast This command enables the forwarding of network-directed broadcasts. When enabled, network directed broadcasts are forwarded. When disabled they are dropped. Default disabled Format ip netdirbcast Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 252
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The minimum IP MTU is 68 bytes.The maximum IP MTU is 1500 bytes. Default 1500 bytes Format ip mtu Mode Interface Config 14.2.9.1 no ip mtu This command resets the ip mtu to the default value. Format no ip mtu
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 253
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.13 clear ip route mpls This command removes only the MPLS route entries associated with from the route table. Format clear ip route mpls Mode Privileged EXEC 14.2.14 clear ip route ospf
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 254
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.16 clear ip route rip This command removes all the route entries learned over the network from OSPF protocol. Format clear ip route rip Mode Privileged EXEC 14.2.17 clear ip route rip This command removes
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 255
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.19 show ip interface This command displays all pertinent information about the IP interface. Format show ip interface Modes Privileged EXEC User EXEC Primary IP Address Displays the primary IP address and subnet
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 256
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Encapsulation Type IP MTU Is the encapsulation type for the specified interface. The types are: Ethernet or SNAP. Displays the maximum transmission unit (MTU) size of a frame, in bytes. 14.2.20 show ip interface This command
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 257
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- For each Next Hop Next Hop Intf Next Hop IP Address The outgoing router interface to use when forwarding traffic to the next destination. The outgoing router IP address to use when forwarding traffic to
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 258
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Network Address Is a valid network address identifying the network on the specified interface. Subnet Mask Protocol Is a mask of the network and host portion of the IP address show ip route preferences Modes Privileged EXEC User EXEC Local
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 259
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.2.25 show ip stats This command displays IP statistical information. Refer to RFC 1213 for more information about the fields that are displayed. Format show ip stats Modes Privileged EXEC User EXEC 14.3 Router
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 260
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.3.2.1 no ip irdp address This command configures the default address to be used to advertise the router for the interface. Format no ip irdp address Mode Interface Config 14.3.3 ip irdp holdtime This command
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 261
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.3.5 ip irdp minadvertinterval This command configures the minimum time, in seconds, allowed between sending router advertisements from the interface. The range for minadvertinterval is three to the value of maxadvertinterval. Default 0.75
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 262
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Interface Ad Mode Advertise Address Max Int Min Int Hold Time Preference Shows the . Displays the advertise mode, which indicates whether router discovery is enabled or disabled on this interface. Displays the IP address to
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 263
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.4.2 show ip vlan This command displays the VLAN routing information for all VLANs with routing enabled. Format show ip vlan Modes Privileged EXEC User EXEC MAC Address used by Routing VLANs Is the MAC Address associated with
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 264
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.1.1 no ip vrrp This command disables the VRRP protocol on an interface. This command also removes a virtual router IP address as a secondary IP address on an interface. The parameter is the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 265
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.3.1 no ip vrrp mode This command disables the virtual router configured on the specified interface. Disabling the status field stops a virtual router. Format no ip vrrp mode Mode Interface
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 266
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.6 ip vrrp preempt This command sets the preemption mode value for the virtual router configured on a specified interface. The parameter is the virtual router ID, which is an integer from 1 to 255 Default enabled Format ip vrrp
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 267
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.5.8 ip vrrp timers advertise This command sets the frequency, in seconds, that an interface on the specified virtual router sends a virtual router advertisement. Default 1 Format ip vrrp timers advertise
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 268
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- IP TTL errors Zero Priority Packets Received Zero Priority Packets Sent Invalid Type Packets Received Address List Errors Invalid Authentication Type Authentication Type Mismatch Packet Length Errors
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 269
    Managed Switch. This command takes no options. It displays information about each virtual router. Format show ip vrrp interface Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. VRID Represents the router ID of the virtual router. IP Address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 270
    Switches, Software Ver- 14.5.12 show ip vrrp interface This command displays all configuration information and VRRP router statistics of a virtual router configured on a specific interface. Format show ip vrrp interface Modes Privileged EXEC User EXEC IP Address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 271
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.2 enable (OSPF) This command resets the default administrative mode of OSPF in the router (active). Default ip ospf This command enables OSPF on a router interface. Default disabled Format ip ospf Mode Interface Config 14.6.3.1 no ip
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 272
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.4.1 no 1583compatibility This command disables OSPF 1583 compatibility. Format no 1583compatibility Mode Router OSPF Config 14.6.5 area default-cost This command configures the monetary default cost for the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 273
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.8 area nssa no-redistribute (OSPF) This command configures the NSSA ABR so that learned external routes will not be redistributed to the NSSA.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 274
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.12 area range This command creates a specified area range for a specified NSSA. The is a valid IP address. The is a valid subnet mask. The LSDB type must be specified by either
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 275
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.13.1 no area stub This command area identified by . The Summary LSA mode is configured as enabled. Default disabled Format area stub summarylsa Mode Router OSPF Config 14.6.14.1
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 276
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.16 area virtual and 255 must be specified.The default value for authentication type is none. Neither the default password key nor the default key id are configured. Default none Format area virtual
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 277
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.17.1 no area virtual-link dead-interval This command configures the default dead interval for the OSPF virtual interface on the virtual interface identified by and . The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 278
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.19.1 no area virtual-link retransmit-interval This command configures the default retransmit interval for the OSPF virtual interface on the virtual interface identified by and . The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 279
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.21.1 no default-information originate (OSPF) This command is used to control the advertisement of default routes. Format no default-information originate [metric] [metrictype] Mode Router OSPF
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 280
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.24 distribute-list before attempting to leave the Overflow State. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow State until
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 281
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.26 external-lsdb-limit This command configures the external LSDB limit for OSPF. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 282
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.28 ip ospf authentication This command Default 10 Format ip ospf cost Mode Interface Config 14.6.29.1 no ip ospf cost This command configures the default cost on an OSPF interface. Format no ip
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 283
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.30 ip ospf dead-interval This command be some multiple of the Hello Interval (i.e. 4). Default 40 Format ip ospf dead-interval Mode Interface Config Routing Commands v1.0, February
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 284
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.30.1 no ip ospf dead-interval This command sets the default OSPF dead interval for the specified interface. Format no ip ospf dead-interval Mode Interface Config 14.6.31 ip ospf hello-interval This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 285
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.33 ip ospf retransmit-interval This command hour). Default 1 Format ip ospf transmit-delay Mode Interface Config 14.6.34.1 no ip ospf transmit-delay This command sets the default OSPF Transit
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 286
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.35 ip ospf mtu-ignore This command disables OSPF maximum transmission unit (MTU) mismatch detection. OSPF Database Description packets specify the size of the largest IP packet that can be sent
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 287
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.37.1 no redistribute This command 38.1 no maximum-paths This command resets the number of paths that OSPF can report for a given destination back to its default value. Format no maximum-paths Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 288
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.40 show ip ospf This command displays information relevant to the OSPF router. Format show ip ospf Mode Privileged EXEC Note: Some of the information below displays only if you enable OSPF and
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 289
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- New LSAs Originated LSAs Received External LSDB Limit Default Metric Default Route Advertise Always Metric Metric Type Maximum Paths Redistributing Source Metric Metric Type Tag Subnets Distribute-List
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 290
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.41 show ip ospf area This command displays information about the area. The identifies the OSPF area that is being displayed. Format show ip ospf area Modes Privileged EXEC User Type Is the Default Metric Type for the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 291
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.42 show ip ospf database This command The AS-Externals are not grouped by area. Format show ip ospf database Modes Privileged EXEC User EXEC Note: The information below is only displayed if OSPF
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 292
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.43 show ip ospf interface This command displays brief information for the IFO object or virtual interface tables. Format show ip ospf interface Modes Privileged EXEC User EXEC Interface Valid slot and
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 293
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.6.44 show ip ospf interface This command displays the information for the IFO object or virtual interface tables. Format show ip ospf interface Modes Privileged EXEC User EXEC IP Address Represents the IP address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 294
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- OSPF is enabled. Format show ip ospf interface stats Modes Privileged EXEC User EXEC OSPF Area ID The -state database, excluding AS External LSAs. IP Address The IP address associated with this OSPF interface. OSPF Interface
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 295
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Neighbor Events External LSA ip ospf neighbor { | all} Modes Privileged EXEC User EXEC Router ID A 4 digit dotted decimal number representing the neighbor interface. IP Address An IP address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 296
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- which router is the . The parameter is the IP address of the neighbor. Format show ip ospf neighbor Modes Privileged EXEC User EXEC Interface Valid slot and port number
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 297
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Events Permanence Hellos Suppressed Retransmission Queue Length Attempt - no recent information has been received from the neighbor but a more concerted effort should be made
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 298
    Privileged EXEC User EXEC Area ID Is a 32-bit identifier for the created stub area. Type of Service Is the type of service associated with the stub metric. The 7300 Series Managed Switch only supports Normal TOS. Metric Val The metric value is applied based on the TOS. It defaults to the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 299
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Modes Area Id Neighbor Hello Interval Dead Interval Retransmit Interval Transit Delay show ip ospf virtual-link Privileged EXEC User EXEC The area id of the requested OSPF area. The neighbor
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 300
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- State ) This command resets the default administrative mode of RIP in the router (active). Default enabled Format enable Config 14.7.3 ip rip This command enables RIP on a router interface. Default disabled Format ip rip Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 301
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.3.1 no ip rip This command disables RIP on a router interface. Format no ip rip Mode Interface Config 14.7.4 auto-summary This command enables the RIP auto-summarization mode. Default disabled Format auto
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 302
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.6.1 no default-metric (RIP) This command is used to reset the default metric of distributed routes to its default value. Format no default-metric Mode Router RIP Config 14.7.7 distance rip This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 303
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.8.2 no default-information originate This command is used to control the advertisement of default routes. Format no default-information originate Mode Router RIP Config 14.7.9 ip rip authentication This command
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 304
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.10.1 no ip rip receive version This command configures the interface to allow RIP control packets of the default version(s) to be received. Format no ip rip receive version Mode Interface Config
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 305
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.13 split-horizon This command sets the RIP split horizon mode. Default simple Format split-horizon {none | simple | poison} Mode Router RIP Config 14.7.13.1 no split-horizon This command sets
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 306
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.15 show ip rip This command displays information relevant to the RIP router. Format show ip rip Modes Privileged EXEC User , but the metric will be set to infinity. The default is simple Auto Summary Mode Enable or disable. If enabled
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 307
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 14.7.16 show ip rip interface This command displays general information for each RIP interface. For this command to display successful results routing must be enabled per interface (i.e. ip rip). Format show ip rip interface
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 308
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Link State Indicates whether the RIP interface is up or down. This is a configured value. Authentication Type The RIP Authentication Type for the specified interface. The types are none, simple, and encrypt. This is a configured value. Default
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 309
    the 7300 Series Managed Switch CLI. The 7300 Series Managed Switch supports IGMP Versions 1, 2, use to configure IGMP snooping. 15.1.1 ip igmpsnooping This command enables IGMP Snooping on the on a particular VLAN and can enable IGMP snooping on all interfaces participating in a VLAN. IGMP Snooping
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 310
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- If address versus the IP address. • Flooding of unregistered multicast data packets to all ports in the VLAN. Default disabled Format ip igmpsnooping Modes Global Config Interface Config VLAN Mode 15.1.1.1 no ip
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 311
    Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.2.1 no ip igmpsnooping interfacemode This command disables IGMP Snooping on all interfaces. Format no ip igmpsnooping interfacemode Mode Global Config 15.1.3 ip igmpsnooping groupmembership-interval This
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 312
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.4 ip igmpsnooping maxresponse This command sets the IGMP Maximum Response time for the system, on a particular interface or VLAN. The Maximum Response time is the amount of time in seconds that a
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 313
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.5.1 no ip igmpsnooping mcrtexpiretime This command sets the Multicast Router Present Expiration time to 0. The time is set for the system, on a particular interface or a VLAN. Format no ip igmpsnooping mcrtexpiretime
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 314
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.1.7.1 no ip igmp mrouter interface This command disables the forwarding of IGMP packets to a multicast router via this interface. Format no ip igmp mrouter interface Mode Interface Config 15.1.8 ip igmpsnooping unknown
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 315
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Admin Mode Interfaces Enabled for IGMP Snooping Multicast Control Frame Count VLANS Enabled for IGMP Snooping This indicates whether or not IGMP Snooping is active on the switch. This is the list of
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 316
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- When you specify a value for , the following additional information appears: VLAN Admin Mode Indicates whether IGMP Snooping is active on the VLAN. 15.2.2 show ip igmp mrouter interface This command
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 317
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Type Description Interfaces displayed as a MAC address and VLAN ID combination of 8 bytes. Displays the type of the entry, which is either static (added by the user) or dynamic (added to the table as a
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 318
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- • IGMP Snooping Querier Address (a configurable globally) 'or' • Switch Management Interface Address 'or' • First configured interface address (for L3 switches only) The switch will check for each of these IP addresses not being
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 319
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15.3.3 ip igmpsnooping querier query-interval To configure the IGMP querier query interval for a VLAN , use the ip igmpsnooping querier query-interval command. Valid range for
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 320
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 15-12 v1.0, February 2007 IGMP Snooping Commands
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 321
    Ethernet Commands available in the FSM7326P Switch software. The IEEE 802.3 Ethernet PoE) is a technology that can integrate data, voice and power on a LAN. PoE supplies reliable, uninterrupted power to Internet Protocol (IP power-data network solves that problem and allows greater flexibility and
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 322
    of service (QoS) where key users are given higher priority to power in the event of a outage. Voice-over IP (VoIP), is the transmission of telephone calls over a data network like one of the many networks that make up the Internet. Other NETGEAR products that work with the 7300 Series Managed Switch
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 323
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.1 poe This command enables or disables the Power over Ethernet function on the specified port(s). Default enable Format poe Mode Global Config 16.1.2 poe priority This command sets the
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 324
    for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.4 poe usagethreshold This command Default 80 Format poe usagethreshold Mode Global Config 16.1.5 show poe port info This command displays a summary for the ports that support the PoE function. Format show poe
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 325
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16.1.5.3 Limit The LIMIT field is the preset limit defined by the "config poe port POE device • Fault-the POE device is not IEEE compliance, no power is provided • Test-the port is in testing state • Other Fault-the port has experience problems
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 326
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 16-6 v1.0, February 2007 Power Over Ethernet Commands
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 327
    17-17 • Section 17.3 "Logging Commands" on page 17-22 • Section 17.4 "CLI Command Logging Command" on page 17-27 • Section 17.5 "Configuration Scripting Commands" on page to and from the switch. • Clear commands clear some or all of the settings to factory defaults. System Maintenance Commands v1
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 328
    Format show arp switch Mode Privileged EXEC MAC Address A unicast MAC address for which the switch has forwarding and/or filtering information. The format is 6 two-digit hexadecimal numbers that are separated by colons, for example 01:23:45:67:89:AB IP Address The IP address assigned to each
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 329
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Switch Description Machine Type Machine Model Serial Number FRU Number Part Number Maintenance Level Manufacturer Burned in MAC Address Software Version Operating System Network Processing Device Additional
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 330
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- The display parameters, when the argument is < The total number of packets received that were directed to the broadcast address. Note that this does not include multicast packets. Packets Received With
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 331
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Transmitted Without Error Broadcast Packets Transmitted Transmit Packet Errors Address Entries Currently In Use VLAN Entries Currently In Use Time Since Counters Last Cleared Total number of
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 332
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- before and after a common interval. The result of this equation is the value Utilization which is the percent utilization of the Ethernet segment on a
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 333
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- multicast address. Note that this number does not include packets directed to the broadcast address. Broadcast section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 334
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Received Packets Not Forwarded VLAN occurs while that tree is being modified. Reserved Address Discards - The number of frames discarded that are destined to an IEEE 802.1 reserved address and are not supported
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 335
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Transmitted Octets Upstream Threshold - The number of frames discarded due to lack of cell descriptors available for that packet's priority level. Total Bytes -
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 336
    Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Packets Transmitted Successfully Transmit number of packets that higher-level protocols requested be transmitted to the Broadcast address, including those that were discarded or not sent. Total Errors - The
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 337
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Protocol Statistics Multiple Collision this port when a lookup on a particular VLAN occurs while that entry in the VLAN table is being modified, or if the VLAN has not been configured. BPDU's received -
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 338
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Dot1x Statistics Time Since Counters Last that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address. Broadcast Packets Received - The total
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 339
    ProSafe 7300 Series Layer-3 Switches, Software Address Table for this switch. Maximum VLAN Entries - The maximum number of Virtual LANs (VLANs) allowed on this switch. Most VLAN Entries Ever Used - The largest number of VLANs that have been active on this switch since the last reboot. Static VLAN
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 340
    ProSafe 7300 Series Layer-3 Switches, Software Ver- Time Since Counters Last Cleared VLAN Deletes - The number of VLANs on this switch occurred since the last reset. The number of Address to display the table entry for the requested MAC address and all entries following the requested MAC address
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 341
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode Mac Address Interface Interface Index Status Static Learned Management Self GMRP Learned Other show mac-addr-table [ | all] Privileged EXEC A unicast MAC address for which the switch has forwarding and
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 342
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.1.9 show running-config Use this command to display/capture the current setting of different protocol packages supported on the switch. This command displays/captures commands with settings/ configurations that differ from the default value
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 343
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- System Name System Location System Contact System ObjectID System Up Time MIBs Supported Name used to identify the switch.The factory default is blank. To configure the system name, see Section 10.1.1 "
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 344
    Format clear igmpsnooping Mode Privileged EXEC 17.2.5 clear pass This command resets all user passwords to the factory defaults without powering off the switch. You are prompted to confirm that the password reset should proceed. Format clear pass Mode Privileged EXEC 17.2.6 enable passwd
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 345
    the ProSafe 7300 Series Layer-3 Switches, Software Ver- Format Mode clear traplog Privileged EXEC 17.2.9 clear vlan This command resets VLAN configuration parameters to the factory defaults. Format clear vlan Mode Privileged EXEC 17.2.10 copy The copy command uploads and downloads files
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 346
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Table 17-1. Copy Parameters (continued) Source Destination < (SSH) Command" on page 3-15. Downloads an SSH key file. Downloads an SSH key file. Downloads an HTTP secure-server certificate. For more
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 347
    default VLAN (VLAN 1), as long as there is a physical path between the switch and the workstation. The terminal interface sends three pings to the target station. Format ping Modes Privileged EXEC, User EXEC 17.2.13 reload This command resets the switch without powering it off. Reset
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 348
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3 Logging Commands This section capacity. Otherwise when the log file reaches full capacity, logging stops. Default enabled Format logging buffered wrap Mode Privileged EXEC 17.3.2.1 no logging
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 349
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17 You can configure up to eight hosts. The is the IP address of the logging host. The value is a port number from (4), notice (5), informational (6), or debug (7). Default port - 514; level - critical; Format
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 350
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3.6 logging port This command sets the local port number of the LOG client for logging messages. The can be in the range from 1 to 65535. Default 514 Format logging port Mode
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 351
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- Console Logging Severity Filter Buffered Logging Administrative Mode Buffered Logging Severity Filter Historical Logging Administrative Mode Historical Logging Severity Filter Syslog Logging Administrative
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 352
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.3.9 show logging buffered This (Used for deleting hosts) Severity Level The minimum severity to log to the specified address. Port Displays the server port number, which is the port on the local host
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 353
    the 7300 Series Managed Switch software to log all CLI commands issued on the system. Default enabled Format logging cli-command Mode Global Config 17.4.1.1 no logging cli-command This command disables the CLI command Logging feature. Format no logging cli-command Mode Global Config
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 354
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.5 Configuration Scripting Commands . Then, you can download the edited files to the system and apply the new configuration. You can apply configuration scripts to one or more switches with no or minor
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 355
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.5.2 script delete This command deletes a specified script where the parameter is the name of the script to delete. The option deletes all the scripts present on the switch problems. It might not identify all problems
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 356
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.6 Packet Capture Packet capture commands assist in troubleshooting protocol-related problems with the management CPU. The packets to and from the management CPU can be captured in an internally allocated
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 357
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.6.3 capture all packets This around to allow continuous packet caputure. Format capture wrap Mode Global Config Default Enabled 17.6.4.1 no capture all packets This command disables the Buffer
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 358
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.6.5 show capture packets This command displays packets being captured from the buffer. The output of the show command can be redirected to a text
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 359
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17.8.2 terminal no length This command resets the number of lines displayed by the show running-config command before pausing to the default value of 18. Format terminal no length Mode Global Config
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 360
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 17-34 v1.0, February 2007 System Maintenance Commands
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 361
    138) • TACACS Server (port 49) • Time Service (port 37) The system supports a maximum of 128 interface address-port pairs. For example, you can have a single routing interface. When the switch receives a broadcast UDP packet on a routing interface, the UDP port to IP address mapping table is checked.
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 362
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 18.1 UDP Relay Configuration Commands This section describes configuration commands for setting up UDP relay service. 18.1.1 ip helper-address (global config mode) Use the Global Configuration ip helper-address command to have
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 363
    ProSafe 7300 Series Layer-3 Switches, Software Ver- 18.1.2 ip helper-address (interface config mode) The ip helper-address interface configuration command enables forwarding User not specified, packets for the default services are forwarded to the helper address. Mode Interface Config 18.2 UDP
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 364
    Command Line Interface Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 18-4 v1.0, February 2007 UDP Relay Commands
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 365
    brief show ip ospf virtual-link show ip vrrp interface brief show ip vrrp interface show monitor show monitor session shiow msglog show logging buferred show port-channel brief show port-channel show remotecon show telnet show service-policy show service-policy in show vlan brief show
  • Netgear GSM7324 | FSM7326P Command line reference manual - Page 366
    Reference for the ProSafe 7300 Series Layer-3 Switches, Software Ver- 3.0.3.4 Command ip igmpsnooping minresponse snmp-server traps snmp-server traps bcaststorm snmp-server traps linkmode snmp-server traps multiusers snmp-server traps stpmode (replaced by interface range command) ip
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
202-10236-01
February 2007
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Command Line Interface
Reference for the ProSafe
7300 Series Layer-3
Switches, Software
Version 6.0