Netgear WG102 WG102 Reference Manual - Page 34

EPLOY, CCESS, Understanding Basic Wireless Settings, Advanced Configuration - setup

Get Netgear WG102 - ProSafe Wireless Access Point PDF manuals and user guides
UPC - 606449037678
View all Netgear WG102 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Reference Manual for the NETGEAR WG102 ProSafe 802.11g Wireless Access Point b. Click the Wireless Settings link in the Setup section of the main menu to view the Wireless Settings menu. Figure 3-5: Basic Wireless Settings menu c. Configure the wireless interface for wireless access. See the online help or the Understanding Basic Wireless Settings topic of this Reference Manual for full instructions. Note: You must set the Country/Region. It may not be legal to operate the wireless access point in a region other than one of those identified in this field. Now that you have finished the setup steps, you are ready to deploy the WG102 in your network. If needed, you can now reconfigure the computer you used in step 1 back to its original TCP/IP settings. 3 DEPLOY THE WG102 ACCESS POINT a. Disconnect the WG102 and position it where you will deploy it. The best location is elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless coverage area, and within line of sight of all the mobile devices. b. Lift the antenna on either side so that they are vertical. Note: Consult the antenna positioning and wireless mode configuration information in the Advanced Configuration chapter of the Reference Manual. c. Connect an Ethernet cable from your WG102 Access Point to a LAN port on your router, switch, or hub. 3-9 Basic Installation and Configuration October 2004

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Reference Manual for the NETGEAR WG102 ProSafe 802.11g Wireless Access Point
3-9
Basic Installation and Configuration
October 2004
b.
Click the Wireless Settings link in the Setup section of the main menu to view the Wireless
Settings menu.
Figure 3-5: Basic Wireless Settings menu
c.
Configure the wireless interface for wireless access. See the online help or the
Understanding Basic Wireless Settings
topic of this Reference Manual for full
instructions.
Note:
You must set the Country/Region. It may not be legal to operate the wireless access
point in a region other than one of those identified in this field.
Now that you have finished the setup steps, you are ready to deploy the WG102 in your
network. If needed, you can now reconfigure the computer you used in step 1 back to its
original TCP/IP settings.
3
D
EPLOY
THE
WG102 A
CCESS
P
OINT
a.
Disconnect the WG102 and position it where you will deploy it. The best location is
elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless
coverage area, and within line of sight of all the mobile devices.
b.
Lift the antenna on either side so that they are vertical.
Note:
Consult the antenna positioning and wireless mode configuration information in the
Advanced Configuration
chapter of the Reference Manual.
c.
Connect an Ethernet cable from your WG102 Access Point to a LAN port on your router,
switch, or hub.