Netgear WG311v1 WG311 Installation Guide - Page 52

Shared Key Authentication, 11b Authentication, Open System Steps

Get Netgear WG311v1 - 54 Mbps Wireless PCI Adapter PDF manuals and user guides View all Netgear WG311v1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WG311 802.11b Authentication Open System Steps 1) Authentication request sent to AP Access Point Client attempting to connect 2) AP authenticates 3) Client connects to network Cable/DSL ProSafeWirelessVPN Security Firewall PWR TEST IN TER N ET LNK W LA N LO CA L MODEL FVM318 100 ACT Enable LNK/ACT 1 2 3 4 5 6 7 8 CSU/DSU or DLS modem Figure 3-8: 802.11 open system authentication Shared Key Authentication The following steps occur when two devices use Shared Key Authentication: 1. The station sends an authentication request to the access point. 2. The access point sends challenge text to the station. 3. The station uses its configured 64-bit or 128-bit default key to encrypt the challenge text, and sends the encrypted text to the access point. 4. The access point decrypts the encrypted text using its configured WEP Key that corresponds to the station's default key. The access point compares the decrypted text with the original challenge text. If the decrypted text matches the original challenge text, then the access point and the station share the same WEP Key and the access point authenticates the station. 5. The station connects to the network. If the decrypted text does not match the original challenge text (i.e., the access point and station do not share the same WEP Key), then the access point will refuse to authenticate the station and the station will be unable to communicate with either the 802.11 network or Ethernet network. This process is illustrated in below. B-4 Wireless Networking Basics

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Installation Guide for the NETGEAR 54 Mbps Wireless PCI Adapter WG311
B-4
Wireless Networking Basics
Figure 3-8:
802.11 open system authentication
Shared Key Authentication
The following steps occur when two devices use Shared Key Authentication:
1.
The station sends an authentication request to the access point.
2.
The access point sends challenge text to the station.
3.
The station uses its configured 64-bit or 128-bit default key to encrypt the challenge text, and
sends the encrypted text to the access point.
4.
The access point decrypts the encrypted text using its configured WEP Key that corresponds
to the station’s default key. The access point compares the decrypted text with the original
challenge text. If the decrypted text matches the original challenge text, then the access point
and the station share the same WEP Key and the access point authenticates the station.
5.
The station connects to the network.
If the decrypted text does not match the original challenge text (i.e., the access point and station do
not share the same WEP Key), then the access point will refuse to authenticate the station and the
station will be unable to communicate with either the 802.11 network or Ethernet network.
This process is illustrated in below.
FVM318
Access Point
1) Authentication request sent to AP
2) AP authenticates
3) Client connects to network
802.11b Authentication
Open System Steps
CSU/DSU
or DLS modem
Client
attempting
to connect