NordicTrack C 950 Pro Treadmill English Manual - Page 13

Remove and discard the four indicated

Get NordicTrack C 950 Pro Treadmill PDF manuals and user guides View all NordicTrack C 950 Pro Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

8. Attach a Handrail (86) to the Right Upright (90) with two 5/16" x 2 1/2" Screws (28) and two 5/16" Star Washers (11). Be careful not to pinch the Upright Wire (81). Do not fully tighten the Screws yet. Attach the other Handrail (86) to the Left Upright (89) in the same way. Note: There is no wire on the left side. Remove and discard the four indicated screws (C). 8 28 11 C 86 89 28 86 11 C 90 81 9. Position the Pulse Crossbar (93) with the pulse wire (D) on the left side as shown. Start four #10 x 3/4" Screws (9) with four #10 Star Washers (5) into the Pulse Crossbar and the Handrails (86). Insert the pulse wire (D) through the looped Cable Tie (99) on the left Handrail (86). Next, slide the Pulse Crossbar (93) as far in the direction shown as possible, and then tighten the 9 9 86 28 D 5 99 93 Wire Tie 81 86 9 #10 x 3/4" Screws (9). Do not overtighten the Screws. 5 28 Remove the wire tie from the Upright Wire (81). Tighten all four 5/16" x 2 1/2" Screws (28). 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
13
8.
Attach a Handrail (86) to the Right Upright
(90) with two 5/16" x 2 1/2" Screws (28) and
two 5/16" Star Washers (11).
Be careful not
to pinch the Upright Wire (81). Do not fully
tighten the Screws yet.
Attach the other Handrail (86) to the Left
Upright (89) in the same way.
Note: There is no
wire on the left side.
Remove and discard the four indicated
screws (C).
8
89
86
28
11
86
C
C
9.
Position the Pulse Crossbar (93) with the pulse
wire (D) on the left side as shown. Start four #10
x 3/4" Screws (9) with four #10 Star Washers (5)
into the Pulse Crossbar and the Handrails (86).
Insert the pulse wire (D) through the looped
Cable Tie (99) on the left Handrail (86).
Next, slide the Pulse Crossbar (93) as far in the
direction shown as possible, and then tighten the
#10 x 3/4" Screws (9).
Do not overtighten the
Screws.
Remove the wire tie from the Upright Wire (81).
Tighten all four 5/16" x 2 1/2" Screws (28).
9
5
Wire
Tie
5
9
9
93
81
28
11
90
28
28
86
86
D
81
99